RESUMEN
In this study, sodium alginate/chitosan/halloysite nanotube composites were prepared by three-dimensional printing and characterized in terms of morphology, viscosity, thermal properties, and methylene blue (MB) adsorption performance. The high specific surface area and extensively microporous structure of these composites allowed for effective MB removal from wastewater; specifically, a removal efficiency of 80% was obtained after a 60 min treatment at an adsorbent loading of 1 g L-1 and an MB concentration of 80 mg L-1, while the maximum MB adsorption capacity equaled 376.3 mg g-1. Adsorption kinetics and isotherms were well described by quasi-second-order and Langmuir models, respectively. The composites largely retained their adsorption performance after five adsorption-desorption cycles and were concluded to hold great promise for MB removal from wastewater.
RESUMEN
Many experimental studies have proved that ion dynamics in a single-digit nanopore with dimensions comparable to the Debye length deviate from the bulk values, but we still have critical knowledge gaps in our understanding of ion transport in nanoconfinement. For many energy devices and sensor designs of nanoporous materials, ion mobility is a key parameter for the performance of nanofluidic equipment. However, investigating ion mobility remains an experimental challenge. This study experimentally investigated the monovalent ion dynamics of single-digit nanopores from the perspective of ionic conductance. In this article, we present a theory that is sufficient for a basic understanding of ion transport through a single-digit nanopore, and we subdivided and separately analyzed the contribution of each conductance component. These conclusions will be useful not only in understanding the behavior of ion migration but also in the design of high-performance nanofluidic devices.
RESUMEN
In this study, a bilayer antibacterial chromogenic material was prepared using chitosan (CS) and hydroxyethyl cellulose (HEC) as inner substrate, mulberry anthocyanins (MA) as a natural tracer, and titanium dioxide nanoparticles (nano-TiO2)/CS:HEC as a bacteriostatic agent for the outer layer. By investigating their apparent viscosity and suitability for 3D printing links, the optimal ratio of the substrates was determined to be CS:HEC = 3:3. Viscosity of the CH was moderate. The printing process was consistent and exhibited no breakage or clogging. The printed image was highly stable and not susceptible to collapse and diffusion. Scanning electron microscopy and infrared spectroscopy indicated that intermolecular binding between the substances exhibited good compatibility. Titanium dioxide nanoparticles (nano-TiO2) were evenly distributed in the CH and no agglomeration was observed. The inner film fill rates affected the overall performance of the chromogenic material, with strong inhibitory effects against Escherichia coli and Staphylococcus aureus at different temperatures, as well as strong color stability. The experimental results indicated that the double-layer antibacterial chromogenic material can, to a certain extent, extend the shelf life of litchi fruit and determine the extent of its freshness. Therefore, from this study, we can infer that the research and development of active materials have a certain reference value.
RESUMEN
As an advanced manufacturing technology that has been developed in recent years, three-dimensional (3D) printing of macromolecular materials can create complex-shaped components that cannot be realized by traditional processing. However, only a few types of macromolecular materials are suitable for 3D printing: the structure must have a single function, and manufacturing macromolecular functional devices is difficult. In this study, using poly lactic acid (PLA) as a matrix, conductive composites were prepared by adding various contents of multi-walled carbon nanotubes (MWCNTs). The printability and properties of MWCNT/PLA composites with different MWCNT proportions were studied by using the fused deposition modeling (FDM) processing technology of 3D printing. The experimental results showed that high conductivity can be realized in 3D-printed products with a composite material containing 5% MWCNTs; its conductivity was 0.4 ± 0.2 S/cm, its tensile strength was 78.4 ± 12.4 MPa, and its elongation at break was 94.4% ± 14.3%. It had a good melt flow rate and thermal properties, and it enabled smooth printing, thus meeting all the requirements for the 3D printing of consumables.