Experimental Requirements for High-Temperature Solid-State Electrochemical TEM Experiments.

The ability to perform both electrochemical and structural/elemental characterization in the same experiment and at the nanoscale allows to directly link electrochemical performance to the material properties and their evolution over time and operating conditions. Such experiments can be important for the further development of solid oxide cells, solid-state batteries, thermal electrical devices, and other solid-state electrochemical devices. The experimental requirements for conducting solid-state electrochemical TEM experiments in general, including sample preparation, electrochemical measurements, failure factors, and possibilities for optimization, are presented and discussed. Particularly, the methodology of performing reliable electrochemical impedance spectroscopy measurements in reactive gases and at elevated temperatures for both single materials and solid oxide cells is described. The presented results include impedance measurements of electronic conductors, an ionic conductor, and a mixed ionic and electronic conductor, all materials typically applied in solid oxide fuel and electrolysis cells. It is shown that how TEM and impedance spectroscopy can be synergically integrated to measure the transport and surface exchange properties of materials with nanoscale dimensions and to visualize their structural and elemental evolution via TEM/STEM imaging and spectroscopy.

Thermal dynamics of few-layer-graphene seals.

Being of atomic thickness, graphene is the thinnest imaginable membrane. While graphene's basal plane is highly impermeable at the molecular level, the impermeability is, in practice, compromised by leakage pathways located at the graphene-substrate interface. Here, we provide a kinetic analysis of such interface-mediated leakage by probing gas trapped in graphene-sealed SiO2 cavities versus time and temperature using electron energy loss spectroscopy. The results show that gas leakage exhibits an Arrhenius-type temperature dependency with apparent activation energies between 0.2 and 0.7 eV. Surprisingly, the interface leak rate can be improved by several orders of magnitude by thermal processing, which alters the kinetic parameters of the temperature dependency. The present study thus provides fundamental insight into the leakage mechanism while simultaneously demonstrating thermal processing as a generic approach for tightening graphene-based-seals with applications within chemistry and biology.

Ion-beam deposited platinum as electrical contacting material in operando electron microscopy experiments at elevated temperatures.

Establishing a stable and well conducting contacting material is critical for operando electron microscopy experiments of electrical and electrochemical devices at elevated temperatures. In this contribution, the nanostructure and electrical conductivity of ion beam deposited Pt are investigated both in vacuum and in oxygen as a function of temperature. Its microstructure is relatively stable up to a temperature of approx. 800°C and up to an applied current density of approx. 100 kA/cm2 . Its conductivity increases with temperature, attributed to densification, with changes in the hydrocarbon matrix being less important. Recommendations are provided with respect to the Pt deposition parameters in terms of maximizing stability and minimizing electrical resistance. RESEARCH HIGHLIGHTS: It is feasible to use ion beam deposited Pt as electrical contacting material in operando electron microscopy. The deposited Pt is relatively stable up to 800°C and approx. 100 kA/cm2 . The resistivity can be reduced by increasing the applied ion current during deposition and by thermal annealing at a temperature of 500°C in a few mbar of oxygen.

Electrochemical Impedance Spectroscopy Integrated with Environmental Transmission Electron Microscopy.

The concept of combining electrical impedance spectroscopy (EIS) with environmental transmission electron microscopy (ETEM) is demonstrated by testing a specially designed micro gadolinia-doped ceria (CGO) sample in reactive gasses (O2 and H2 /H2 O), at elevated temperatures (room temperature-800 °C) and with applied electrical potentials. The EIS-TEM method provides structural and compositional information with direct correlation to the electrochemical performance. It is demonstrated that reliable EIS measurements can be achieved in the TEM for a sample with nanoscale dimensions. Specifically, the ionic and electronic conductivity, the surface exchange resistivity, and the volume-specific chemical capacitance are in good agreement with results from more standardized electrochemical tests on macroscopic samples. CGO is chosen as a test material due to its relevance for solid oxide electrochemical reactions where its electrochemical performance depends on temperature and gas environment. As expected, the results show increased conductivity and lower surface exchange resistance in H2 /H2 O gas mixtures where the oxygen partial pressure is low compared to experiments in pure O2 . The developed EIS-TEM platform is an important tool in promoting the understanding of nanoscale processes for green energy technologies, e.g., solid oxide electrolysis/fuel cells, batteries, thermoelectric devices, etc.

In situoff-axis electron holography of real-time dopant diffusion in GaAs nanowires.

Off-axis electron holography was used to reveal remote doping in GaAs nanowires occurring duringin situannealing in a transmission electron microscope. Dynamic changes to the electrostatic potential caused by carbon dopant diffusion upon annealing were measured across GaAs nanowires with radial p-p+ core-shell junctions. Electrostatic potential profiles were extracted from holographic phase maps and built-in potentials (Vbi) and depletion layer widths (DLWs) were estimated as function of temperature over 300-873 K. Simulations in absence of remote doping predict a significant increase ofVbiand DLWs with temperature. In contrast, we measured experimentally a nearly constantVbiand a weak increase of DLWs. Moreover, we observed the appearance of a depression in the potential profile of the core upon annealing. We attribute these deviations from the predicted behavior to carbon diffusion from the shell to the core through the nanowire sidewalls, i.e. to remote doping, becoming significant at 673 K. The DLW in the p and p+ regions are in the 10-30 nm range.

Spatial Image Resolution Assessment by Fourier Analysis (SIRAF).

Determining spatial resolution from images is crucial when optimizing focus, determining smallest resolvable object, and assessing size measurement uncertainties. However, no standard algorithm exists to measure resolution from electron microscopy (EM) images, though several have been proposed, where most require user decisions. We present the Spatial Image Resolution Assessment by Fourier analysis (SIRAF) algorithm that uses fast Fourier transform analysis to estimate resolution directly from a single image without user inputs. The method is derived from the underlying assumption that objects display intensity transitions, resembling a step function blurred by a Gaussian point spread function. This hypothesis is tested and verified on simulated EM images with known resolution. To identify potential pitfalls, the algorithm is also tested on simulated images with a variety of settings, and on real SEM images acquired at different magnification and defocus settings. Finally, the versatility of the method is investigated by assessing resolution in images from several microscopy techniques. It is concluded that the algorithm can assess resolution from a large selection of image types, thereby providing a measure of this fundamental image parameter. It may also improve autofocus methods and guide the optimization of magnification settings when balancing spatial resolution and field of view.

Advanced Materials for Energy-Water Systems: The Central Role of Water/Solid Interfaces in Adsorption, Reactivity, and Transport.

The structure, chemistry, and charge of interfaces between materials and aqueous fluids play a central role in determining properties and performance of numerous water systems. Sensors, membranes, sorbents, and heterogeneous catalysts almost uniformly rely on specific interactions between their surfaces and components dissolved or suspended in the water-and often the water molecules themselves-to detect and mitigate contaminants. Deleterious processes in these systems such as fouling, scaling (inorganic deposits), and corrosion are also governed by interfacial phenomena. Despite the importance of these interfaces, much remains to be learned about their multiscale interactions. Developing a deeper understanding of the molecular- and mesoscale phenomena at water/solid interfaces will be essential to driving innovation to address grand challenges in supplying sufficient fit-for-purpose water in the future. In this Review, we examine the current state of knowledge surrounding adsorption, reactivity, and transport in several key classes of water/solid interfaces, drawing on a synergistic combination of theory, simulation, and experiments, and provide an outlook for prioritizing strategic research directions.

In situ TEM modification of individual silicon nanowires and their charge transport mechanisms.

Correlating the structure and composition of nanowires grown by the vapour-liquid-solid (VLS) mechanism with their electrical properties is essential for designing nanowire devices. In situ transmission electron microscopy (TEM) that can image while simultaneously measuring the current-voltage (I-V) characteristics of individual isolated nanowires is a unique tool for linking changes in structure with electronic transport. Here we grow and electrically connect silicon nanowires inside a TEM to perform in situ electrical measurements on individual nanowires both at high temperature and upon surface oxidation, as well as under ambient conditions. As-grown, the oxide-free nanowires have nonlinear I-V characteristics. We analyse the I-V measurements in terms of both bulk and injection limited transport models, finding Joule heating effects, bulk-limiting effects for thin nanowires and an injection-limiting effect for thick wires when high voltages are applied. When the nanowire surface is modified by in situ oxidation, drastic changes occur in the electronic properties. We investigate the relation between the observed geometry, changes in the surface structure and changes in electronic transport, obtaining information for individual nanowires that is inaccessible to other measuring techniques.

Unhindered Brownian Motion of Individual Nanoparticles in Liquid-Phase Scanning Transmission Electron Microscopy.

Liquid-phase transmission electron microscopy (LPTEM) offers label-free imaging of nanoparticle (NP) processes in liquid with sub-nanometer spatial and millisecond temporal resolution. However, LPTEM studies have reported only on NPs moving orders of magnitude slower than expected from bulk aqueous liquid conditions, likely due to strong interactions with the LPTEM liquid-enclosing membranes. We demonstrate how scanning transmission electron microscope (STEM) imaging can be used to measure the motion of individual NPs and agglomerates, which are not hindered by such interactions. Only at low electron flux do we find that individual NPs exhibit Brownian motion consistent with optical control experiments and theoretical predictions for unhindered passive diffusive motion in bulk liquids. For increasing electron flux, we find increasingly faster than passive motion that still appears effectively Brownian. We discuss the possible origins of this beam-sample interaction. This establishes conditions for the use of STEM as a reliable tool for imaging nanoscale hydrodynamics in situ TEM.

Electron inelastic mean free path in water.

Liquid phase transmission electron microscopy (LPTEM) is rapidly developing as a powerful tool for probing processes in liquid environments with close to atomic resolution. Knowledge of the water thickness is needed for reliable interpretation and modelling of analytical studies in LPTEM, and is particularly essential when using thin liquid layers, required for achieving the highest spatial resolutions. The log-ratio method in electron energy-loss spectroscopy (EELS) is often applied in TEM to quantify the sample thickness, which is measured relative to the inelastic mean free path (λIMFP). However, λIMFP itself is dependent on sample material, the electron energy, and the convergence and divergence angles of the microscope electronoptics. Here, we present a detailed quantitative analysis of the λIMFP of water as functions of the EELS collection angle (ß) at 120 keV and 300 keV in a novel nanochannel liquid cell. We observe good agreement with earlier studies conducted on ice, but find that the most widely used theoretical models significantly underestimate λIMFP of water. We determine an adjusted average energy-loss term Em, water, and characteristic scattering angle θE, water that improve the accuracy. The results provide a comprehensive knowledge of the λIMFP of water (or ice) for reliable interpretation and quantification of observations in LPTEM and cryo-TEM studies.

Complex Aerosol Characterization by Scanning Electron Microscopy Coupled with Energy Dispersive X-ray Spectroscopy.

Particulate matter (PM) air pollution is a central concern for public health. Current legislation relies on a mass concentration basis, despite broad acceptance that mass alone is insufficient to capture the complexity and toxicity of airborne PM, calling for additional and more comprehensive measurement techniques. We study to what extent scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM/EDS) can be applied for physicochemical characterization of complex aerosols, and investigate its potential for separating particle properties on a single particle basis, even for nanosized particles. SEM/EDS analysis is performed on impactor samples of laboratory generated aerosols, consisting of either NaCl, Halloysite fibers, soot-like Printex90 agglomerates, or their combination. The analysis is automated and performed as EDS maps, covering a statistically relevant number of particles, with analysis times of approximately one hour/sample. Derived size distributions are compared to scanning mobility particle sizer (SMPS) and electric low-pressure impactor (ELPI) results. A method is presented to estimate airborne number concentrations and size distributions directly from SEM results, within a factor 10 of SMPS and ELPI outcomes. A classification scheme is developed based on elemental composition, providing class-specific information with individual particle statistics on shape, size, and mixing state. This can identify primary particles for source apportionment and enables easy distinction between fibrous and dense particle classes, e.g. for targeted risk assessments. Overall, the SEM/EDS analysis provides a more detailed physicochemical characterization of PM than online measurements, e.g. SMPS and ELPI. The method has the potential to improve assessments of PM exposure and risk, and facilitates source identification, even without prior knowledge at sampling.

Analysis of Electron Transparent Beam-Sensitive Samples Using Scanning Electron Microscopy Coupled With Energy-Dispersive X-ray Spectroscopy.

Scanning electron microscopy, coupled with energy-dispersive X-ray spectroscopy (EDS), is a powerful tool used in many scientific fields. It can provide nanoscale images, allowing size and morphology measurements, as well as provide information on the spatial distribution of elements in a sample. This study compares the capabilities of a traditional EDS detector with a recently developed annular EDS detector when analyzing electron transparent and beam-sensitive NaCl particles on a TEM grid. The optimal settings for single particle analysis are identified in order to minimize beam damage and optimize sample throughput via the choice of acceleration voltage, EDS acquisition time, and quantification model. Here, a linear combination of two models is used to bridge results for particle sizes, which are neither bulk nor sufficiently thin to assume electron transparent. Additionally, we show that the increased count rate obtainable with the annular detector enables mapping as a viable analysis strategy compared with feature detection methods, which only scan segmented regions. Finally, we discuss advantages and disadvantages of the two analysis strategies.

Mean Inner Potential of Liquid Water.

Improving our experimental and theoretical knowledge of electric potentials at liquid-solid boundaries is essential to achieve a deeper understanding of the driving forces behind interfacial processes. Electron holography has proved successful in probing solid-solid interfaces but requires knowledge of the materials' mean inner potential (MIP, V_{0}), which is a fundamental bulk material property. Combining off-axis electron holography with liquid phase transmission electron microscopy (LPTEM), we provide the first quantitative MIP determination of liquid water V_{0}=+4.48±0.19 V. This value is larger than most theoretical predictions, and to explain the disagreement we assess the dominant factors needed in quantum simulations of liquid water. A precise MIP lays the foundations for nanoscale holographic potential measurements in liquids, and provides a benchmark to improve quantum mechanical descriptions of aqueous systems and their interfaces in, e.g., electrochemistry, solvation processes, and spectroscopy.

Methods for Calibration of Specimen Temperature During In Situ Transmission Electron Microscopy Experiments.

One of the biggest challenges for in situ heating transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM) is the ability to measure the local temperature of the specimen accurately. Despite technological improvements in the construction of TEM/STEM heating holders, the problem of being able to measure the real sample temperature is still the subject of considerable discussion. In this study, we review the present literature on methodologies for temperature calibration. We analyze calibration methods that require the use of a thermometric material in addition to the specimen under study, as well as methods that can be performed directly on the specimen of interest without the need for a previous calibration. Finally, an overview of the most important characteristics of all the treated techniques, including temperature ranges and uncertainties, is provided in order to provide an accessory database to consult before an in situ TEM/STEM temperature calibration experiment.

Improving the foundation for particulate matter risk assessment by individual nanoparticle statistics from electron microscopy analysis.

Air pollution is one of the major contributors to the global burden of disease, with particulate matter (PM) as one of its central concerns. Thus, there is a great need for exposure and risk assessments associated with PM pollution. However, current standard measurement techniques bring no knowledge of particle composition or shape, which have been identified among the crucial parameters for toxicology of inhaled particles. We present a method for collecting aerosols via impaction directly onto Transmission Electron Microscopy (TEM) grids, and based on the measured impactor collection efficiency and observed impact patterns we establish a reproducible imaging routine for automated Scanning Electron Microscopy (SEM) analysis. The method is validated by comparison to scanning mobility particle sizer (SMPS) measurements, where a good agreement is found between the particle size distributions (PSD), ensuring a representative description of the sampled aerosol. We furthermore determine sampling conditions for achieving optimal particle coverage on the TEM grids, allowing for a statistical analysis. In summary, the presented method can provide not only a representative PSD, but also detailed statistics on individual particle geometries. If coupled with Energy-dispersive X-ray spectroscopy (EDS) analysis elemental compositions can be assessed as well. This makes it possible to categorize particles both according to size and shape e.g. round and fibres, or agglomerates, as well as classify them based on their elemental composition e.g. salt, soot, or metals. Combined this method brings crucial knowledge for improving the foundation for PM risk assessments on workplaces and in ambient conditions with complex aerosol pollution.

Three-dimensional iron sulfide-carbon interlocked graphene composites for high-performance sodium-ion storage.

Three-dimensional (3D) carbon-wrapped iron sulfide interlocked graphene (Fe7S8@C-G) composites for high-performance sodium-ion storage are designed and produced through electrostatic interactions and subsequent sulfurization. The iron-based metal-organic frameworks (MOFs, MIL-88-Fe) interact with graphene oxide sheets to form 3D networks, and carbon-wrapped iron sulfide (Fe7S8@C) nanoparticles with high individual-particle conductivity are prepared following a sulfurization process, surrounded by interlocked graphene sheets to enhance the interparticle conductivity. The prepared Fe7S8@C-G composites exhibit not only improved individual-particle and interparticle conductivity to shorten electron/ion diffusion pathways, but also enhanced structural stability to prevent the aggregation of active materials and buffer large volume changes during sodiation/desodiation. As a sodium-ion storage material, the Fe7S8@C-G composites exhibit a reversible capacity of 449 mA h g-1 at 500 mA g-1 after 150 cycles and a retention capacity of 306 mA h g-1 under a current density of 2000 mA g-1. The crucial factors related to the structural changes and stability during cycles have been further investigated. These results demonstrate that the high-performance sodium-ion storage properties are mainly attributed to the uniquely designed three-dimensional configuration.

Engineering the Surface/Interface Structures of Titanium Dioxide Micro and Nano Architectures towards Environmental and Electrochemical Applications.

Titanium dioxide (TiO2) materials have been intensively studied in the past years because of many varied applications. This mini review article focuses on TiO2 micro and nano architectures with the prevalent crystal structures (anatase, rutile, brookite, and TiO2(B)), and summarizes the major advances in the surface and interface engineering and applications in environmental and electrochemical applications. We analyze the advantages of surface/interface engineered TiO2 micro and nano structures, and present the principles and growth mechanisms of TiO2 nanostructures via different strategies, with an emphasis on rational control of the surface and interface structures. We further discuss the applications of TiO2 micro and nano architectures in photocatalysis, lithium/sodium ion batteries, and Li-S batteries. Throughout the discussion, the relationship between the device performance and the surface/interface structures of TiO2 micro and nano structures will be highlighted. Then, we discuss the phase transitions of TiO2 nanostructures and possible strategies of improving the phase stability. The review concludes with a perspective on the current challenges and future research directions.