Selective Direct Laser Writing of Pyrolytic Carbon Microelectrodes in Absorber-Modified SU-8.

Pyrolytic carbon microelectrodes (PCMEs) are a promising alternative to their conventional metallic counterparts for various applications. Thus, methods for the simple and inexpensive patterning of PCMEs are highly sought after. Here, we demonstrate the fabrication of PCMEs through the selective pyrolysis of SU-8 photoresist by irradiation with a low-power, 806 nm, continuous wave, semiconductor-diode laser. The SU-8 was modified by adding Pro-Jet 800NP (FujiFilm) in order to ensure absorbance in the 800 nm range. The SU-8 precursor with absorber was successfully converted into pyrolytic carbon upon laser irradiation, which was not possible without an absorber. We demonstrated that the local laser pyrolysis (LLP) process in an inert nitrogen atmosphere with higher laser power and lower scan speed resulted in higher electrical conductance. The maximum conductivity achieved for a laser-pyrolyzed line was 14.2 ± 3.3 S/cm, with a line width and thickness of 28.3 ± 2.9 µm and 6.0 ± 1.0 µm, respectively, while the narrowest conductive line was just 13.5 ± 0.4 µm wide and 4.9 ± 0.5 µm thick. The LLP process seemed to be self-limiting, as multiple repetitive laser scans did not alter the properties of the carbonized lines. The direct laser writing of adjacent lines with an insulating gap down to ≤5 µm was achieved. Finally, multiple lines were seamlessly joined and intersected, enabling the writing of more complex designs with branching electrodes and the porosity of the carbon lines could be controlled by the scan speed.

Direct evidence for eoarchean iron metabolism?

Metasedimentary rocks from Isua, West Greenland (> 3,700 million years old) contain carbonaceous compounds, compatible with a biogenic origin (Hassenkam, Andersson, Dalby, Mackenzie, & Rosing, 2017; Ohtomo, Kakegawa, Ishida, Nagase, & Rosing, 2014; Rosing, 1999). The metamorphic mineral assemblage with garnet and quartz intergrowths contains layers of carbonaceous inclusions contiguous with carbon-rich sedimentary beds in the host rock. Previous studies (Hassenkam et al., 2017; Ohtomo et al., 2014; Rosing, 1999) on Isua rocks focused on testing the biogenic origin of the carbonaceous material, but here we searched for evidence which could provide new insights into the nature of the life that generated this carbonaceous material. We studied material trapped in inclusions armoured within quartz grains inside garnet porphyroblasts by non-destructive ptychographic X-ray nanotomography (PXCT). The 3D electron density maps generated by PXCT were correlated with maps from X-ray fluorescence tomography and micro-Raman spectroscopy. We found that the material trapped inside inclusions in the quartz grains consist of disordered carbon material encasing domains of iron-rich carbonaceous material. These results corroborate earlier claims (Hassenkam et al., 2017; Ohtomo et al., 2014; Rosing, 1999) for biogenic origins and are compatible with relics of metamorphosed biological material originally containing high iron/carbon ratios, comparable to ratios found in most extant organisms. These iron-rich domains represent the oldest evidence for organic iron complexes in the geologic record and are consistent with Fe-isotopic evidence for metabolic iron fractionation in > 3,700 Ma Isua banded iron formation (Czaja et al., 2013; Whitehouse & Fedo, 2007).

Wafer-scale graphene quality assessment using micro four-point probe mapping.

Micro four-point probes (M4PP) provide rapid and automated lithography-free transport properties of planar surfaces including two-dimensional materials. We perform sheet conductance wafer maps of graphene directly grown on a 100 mm diameter SiC wafer using a multiplexed seven-point probe with minor additional measurement time compared to a four-point probe. Comparing the results of three subprobes we find that compared to a single-probe result, our measurement yield increases from 72%-84% to 97%. The additional data allows for correlation analysis between adjacent subprobes, that must measure the same values in case the sample is uniform on the scale of the electrode pitch. We observe that the relative difference in measured sheet conductance between two adjacent subprobes increase in the transition between large and low conductance regions. We mapped sheet conductance of graphene as it changed over several weeks. Terahertz time-domain spectroscopy conductivity maps both before and after M4PP mapping showed no significant change due to M4PP measurement, with both methods showing the same qualitative changes over time.

Review of fabrication methods of large-area transparent graphene electrodes for industry.

Graphene is a two-dimensional material showing excellent properties for utilization in transparent electrodes; it has low sheet resistance, high optical transmission and is flexible. Whereas the most common transparent electrode material, tin-doped indium-oxide (ITO) is brittle, less transparent and expensive, which limit its compatibility in flexible electronics as well as in low-cost devices. Here we review two large-area fabrication methods for graphene based transparent electrodes for industry: liquid exfoliation and low-pressure chemical vapor deposition (CVD). We discuss the basic methodologies behind the technologies with an emphasis on optical and electrical properties of recent results. State-of-the-art methods for liquid exfoliation have as a figure of merit an electrical and optical conductivity ratio of 43.5, slightly over the minimum required for industry of 35, while CVD reaches as high as 419.

A universal approach for the synthesis of two-dimensional binary compounds.

Only a few of the vast range of potential two-dimensional materials (2D) have been isolated or synthesised to date. Typically, 2D materials are discovered by mechanically exfoliating naturally occurring bulk crystals to produce atomically thin layers, after which a material-specific vapour synthesis method must be developed to grow interesting candidates in a scalable manner. Here we show a general approach for synthesising thin layers of two-dimensional binary compounds. We apply the method to obtain high quality, epitaxial MoS2 films, and extend the principle to the synthesis of a wide range of other materials-both well-known and never-before isolated-including transition metal sulphides, selenides, tellurides, and nitrides. This approach greatly simplifies the synthesis of currently known materials, and provides a general framework for synthesising both predicted and unexpected new 2D compounds.

Lithographic band structure engineering of graphene.

Two-dimensional materials such as graphene allow direct access to the entirety of atoms constituting the crystal. While this makes shaping by lithography particularly attractive as a tool for band structure engineering through quantum confinement effects, edge disorder and contamination have so far limited progress towards experimental realization. Here, we define a superlattice in graphene encapsulated in hexagonal boron nitride, by etching an array of holes through the heterostructure with minimum feature sizes of 12-15 nm. We observe a magnetotransport regime that is distinctly different from the characteristic Landau fan of graphene, with a sizeable bandgap that can be tuned by a magnetic field. The measurements are accurately described by transport simulations and analytical calculations. Finally, we observe strong indications that the lithographically engineered band structure at the main Dirac point is cloned to a satellite peak that appears due to moiré interactions between the graphene and the encapsulating material.

Oxidation of Suspended Graphene: Etch Dynamics and Stability Beyond 1000 °C.

We study the oxidation of clean suspended mono- and few-layer graphene in real time by in situ environmental transmission electron microscopy. At an oxygen pressure below 0.1 mbar, we observe anisotropic oxidation in which armchair-oriented hexagonal holes are formed with a sharp edge roughness below 1 nm. At a higher pressure, we observe an increasingly isotropic oxidation, eventually leading to irregular holes at a pressure of 6 mbar. In addition, we find that few-layer flakes are stable against oxidation at temperatures up to at least 1000 °C in the absence of impurities and electron-beam-induced defects. These findings show, first, that the oxidation behavior of mono- and few-layer graphene depends critically on the intrinsic roughness, cleanliness and any imposed roughness or additional reactivity from a supporting substrate and, second, that the activation energy for oxidation of pristine suspended few-layer graphene is up to 43% higher than previously reported for graphite. In addition, we have developed a cleaning scheme that results in the near-complete removal of hydrocarbon residues over the entire visible sample area. These results have implications for applications of graphene where edge roughness can critically affect the performance of devices and more generally highlight the surprising (meta)stability of the basal plane of suspended bilayer and thicker graphene toward oxidative environments at high temperature.

Scalable and Tunable Periodic Graphene Nanohole Arrays for Mid-Infrared Plasmonics.

Despite its great potential for a wide variety of devices, especially mid-infrared biosensors and photodetectors, graphene plasmonics is still confined to academic research. A major reason is the fact that, so far, expensive and low-throughput lithography techniques are needed to fabricate graphene nanostructures. Here, we report for the first time a detailed experimental study on electrostatically tunable graphene nanohole array surfaces with periods down to 100 nm, showing clear plasmonic response in the range ∼1300-1600 cm-1, which can be fabricated by a scalable nanoimprint technique. Such large area plasmonic nanostructures are suitable for industrial applications, for example, surface-enhanced infrared absorption (SEIRA) sensing, as they combine easy design, extreme field confinement, and the possibility to excite multiple plasmon modes enabling multiband sensing, a feature not readily available in nanoribbons or other localized resonant structures.

Electrical Homogeneity Mapping of Epitaxial Graphene on Silicon Carbide.

Epitaxial graphene is a promising route to wafer-scale production of electronic graphene devices. Chemical vapor deposition of graphene on silicon carbide offers epitaxial growth with layer control but is subject to significant spatial and wafer-to-wafer variability. We use terahertz time-domain spectroscopy and micro four-point probes to analyze the spatial variations of quasi-freestanding bilayer graphene grown on 4 in. silicon carbide (SiC) wafers and find significant variations in electrical properties across large regions, which are even reproduced across graphene on different SiC wafers cut from the same ingot. The dc sheet conductivity of epitaxial graphene was found to vary more than 1 order of magnitude across a 4 in. SiC wafer. To determine the origin of the variations, we compare different optical and scanning probe microscopies with the electrical measurements from nano- to millimeter scale and identify three distinct qualities of graphene, which can be attributed to the microstructure of the SiC surface.

Quality assessment of terahertz time-domain spectroscopy transmission and reflection modes for graphene conductivity mapping.

We present a comparative study of electrical measurements of graphene using terahertz time-domain spectroscopy in transmission and reflection mode, and compare the measured sheet conductivity values to electrical van der Pauw measurements made independently in three different laboratories. Overall median conductivity variations of up to 15% were observed between laboratories, which are attributed mainly to the well-known temperature and humidity dependence of non-encapsulated graphene devices. We conclude that terahertz time-domain spectroscopy performed in either reflection mode or transmission modes are indeed very accurate methods for mapping electrical conductivity of graphene, and that both methods are interchangeable within measurement uncertainties. The conductivity obtained via terahertz time-domain spectroscopy were consistently in agreement with electrical van der Pauw measurements, while offering the additional advantages associated with contactless mapping, such as high throughput, no lithography requirement, and with the spatial mapping directly revealing the presence of any inhomogeneities or isolating defects. The confirmation of the accuracy of reflection-mode removes the requirement of a specialized THz-transparent substrate to accurately measure the conductivity.

Quantitative optical mapping of two-dimensional materials.

The pace of two-dimensional materials (2DM) research has been greatly accelerated by the ability to identify exfoliated thicknesses down to a monolayer from their optical contrast. Since this process requires time-consuming and error-prone manual assignment to avoid false-positives from image features with similar contrast, efforts towards fast and reliable automated assignments schemes is essential. We show that by modelling the expected 2DM contrast in digitally captured images, we can automatically identify candidate regions of 2DM. More importantly, we show a computationally-light machine vision strategy for eliminating false-positives from this set of 2DM candidates through the combined use of binary thresholding, opening and closing filters, and shape-analysis from edge detection. Calculation of data pyramids for arbitrarily high-resolution optical coverage maps of two-dimensional materials produced in this way allows the real-time presentation and processing of this image data in a zoomable interface, enabling large datasets to be explored and analysed with ease. The result is that a standard optical microscope with CCD camera can be used as an analysis tool able to accurately determine the coverage, residue/contamination concentration, and layer number for a wide range of presented 2DMs.

Terahertz wafer-scale mobility mapping of graphene on insulating substrates without a gate.

We demonstrate wafer-scale, non-contact mapping of essential carrier transport parameters, carrier mobility (µdrift), carrier density (Ns), DC sheet conductance (σdc), and carrier scattering time (τsc) in CVD graphene, using spatially resolved terahertz time-domain conductance spectroscopy. σdc and τsc are directly extracted from Drude model fits to terahertz conductance spectra obtained in each pixel of 10 × 10 cm2 maps with a 400 µm step size. σdc- and τsc-maps are translated into µdrift and Ns maps through Boltzmann transport theory for graphene charge carriers and these parameters are directly compared to van der Pauw device measurements on the same wafer. The technique is compatible with all substrate materials that exhibit a reasonably low absorption coefficient for terahertz radiation. This includes many materials used for transferring CVD graphene in production facilities as well as in envisioned products, such as polymer films, glass substrates, cloth, or paper substrates.

A critical assessment of visual identification of marine microplastic using Raman spectroscopy for analysis improvement.

Identification and characterisation of microplastic (MP) is a necessary step to evaluate their concentrations, chemical composition and interactions with biota. MP ≥10µm diameter filtered from below the sea surface in the European and subtropical North Atlantic were simultaneously identified by visual microscopy and Raman micro-spectroscopy. Visually identified particles below 100µm had a significantly lower percentage confirmed by Raman than larger ones indicating that visual identification alone is inappropriate for studies on small microplastics. Sixty-eight percent of visually counted MP (n=1279) were spectroscopically confirmed being plastic. The percentage varied with type, colour and size of the MP. Fibres had a higher success rate (75%) than particles (64%). We tested Raman micro-spectroscopy applicability for MP identification with respect to varying chemical composition (additives), degradation state and organic matter coating. Partially UV-degraded post-consumer plastics provided identifiable Raman spectra for polymers most common among marine MP, i.e. polyethylene and polypropylene.

Defect/oxygen assisted direct write technique for nanopatterning graphene.

High resolution nanopatterning of graphene enables manipulation of electronic, optical and sensing properties of graphene. In this work we present a straightforward technique that does not require any lithographic mask to etch nanopatterns into graphene. The technique relies on the damaged graphene to be etched selectively in an oxygen rich environment with respect to non-damaged graphene. Sub-40 nm features were etched into graphene by selectively exposing it to a 100 keV electron beam and then etching the damaged areas away in a conventional oven. Raman spectroscopy was used to evaluate the extent of damage induced by the electron beam as well as the effects of the selective oxidative etching on the remaining graphene.