Suppression of the plasmon-quenching effect on light amplification in 20-µm-diameter plasmonic whispering gallery mode resonators fabricated from bowl-shaped organic/metal thin films.

Bowl-shaped plasmonic whispering gallery mode (WGM) resonators were fabricated from a 10-nm-thick metal (Al, Ag, or Au) plasmonic layer that was covered with a 100-nm-thick 4,4'-bis(N-carbazolyl)-1,1'-biphenyl spacer layer and a 250-nm-thick 2,7-bis[9,9-di(4-methylphenyl)-fluoren-2-yl]-9,9-di(4-methylphenyl)fluorene light-emitting layer; the layer structure was grown on a 20-µm-diameter silica microsphere. When compared with a reference structure without the plasmonic layer, the resonators, which included either Al or Ag, showed almost the same threshold excitation intensities for generation of amplified spontaneous emission (ASE). This result indicates that the ease of light amplification in the plasmonic resonators was comparable to that in the reference structure. Excitons that exist in the vicinity of metal thin films are generally easy to quench because propagating surface plasmon polaritons (SPPs) absorb the exciton energy. Therefore, the observed comparability demonstrates that the plasmonic WGM resonators overcome this quenching effect on ASE via localization of the SPPs in the vicinity of the excitons.

Characteristics of Sputtered Lead Zirconate Titanate Thin Films With Different Layer Configurations and Large Thickness.

To evaluate the characteristics of Pb(Zr,Ti)O3 (PZT) thin films (about [Formula: see text] thick) with three different sputtering configurations-single-layer (SL) deposition, multilayer (ML) deposition with internal electrodes, and multistep (MS) deposition-were prepared. The SL films exhibited poorer dielectric characteristics than the ML and MS films. The reliability and piezoelectric characteristics were especially high in the MS film, with an [Formula: see text] constant of -9.5 C · m-2. To investigate the porosity of the films, reconstructed 3-D SEM technique is employed. Reconstructed 3-D SEM images revealed decreased void densities in the ML and MS films, which improved their performance. The MS configuration provided the best dielectric and piezoelectric performance of PZT films.

Real-time in vivo dosimetry system based on an optical fiber-coupled microsized photostimulable phosphor for stereotactic body radiation therapy.

PURPOSE: To develop an in vivo dosimeter system for stereotactic body radiation therapy (SBRT) that can perform accurate and precise real-time measurements, using a microsized amount of a photostimulable phosphor (PSP), BaFBr:Eu2+ . METHODS: The sensitive volume of the PSP was 1.26 × 10-5  cm3 . The dosimeter system was designed to apply photostimulation to the PSP after the decay of noise signals, in synchronization with the photon beam pulse of a linear accelerator (LINAC), to eliminate the noise signals completely using a time separation technique. The noise signals included stem signals, and radioluminescence signals generated by the PSP. In addition, the dosimeter system was built on a storage-type dosimeter that could read out a signal after an arbitrary preset number of photon beam pulses were incident. First, the noise and photostimulated luminescence (PSL) signal decay times were measured. Subsequently, we confirmed that the PSL signals could be exclusively read out within the photon beam pulse interval. Finally, using a water phantom, the basic characteristics of the dosimeter system were demonstrated under SBRT conditions, and the feasibility for clinical application was investigated. The reproducibility, dose linearity, dose-rate dependence, temperature dependence, and angular dependence were evaluated. The feasibility was confirmed by measurements at various dose gradients and using a representative treatment plan for a metastatic liver tumor. A clinical plan was created with a two-arc beam volumetric modulated arc therapy using a 10 MV flattening filter-free photon beam. For the water phantom measurements, the clinical plan was compiled into a plan with a fixed gantry angle of 0°. To evaluate the energy dependence during SBRT, the percent depth dose (PDD) was measured and compared with those calculated via Monte Carlo (MC) simulations. RESULTS: All the PSL signals could be read out while eliminating the noise signals within the minimum pulse interval of the LINAC. Stable real-time measurements could be performed with a time resolution of 56 ms (i.e., number of pulses = 20). The dose linearity was good in the dose range of 0.01-100 Gy. The measurements agreed within 1% at dose rates of 40-2400 cGy/min. The temperature and angular dependence were also acceptable since these dependencies had only a negligible effect on the measurements in SBRT. At a dose gradient of 2.21 Gy/mm, the measured dose agreed with that calculated using a treatment planning system (TPS) within the measurement uncertainties due to the probe position. For measurements using a representative treatment plan, the measured dose agreed with that calculated using the TPS within 0.5% at the center of the beam axis. The PDD measurements agreed with the MC calculations to within 1% for field sizes <5 × 5 cm2 . CONCLUSION: The in vivo dosimeter system developed using BaFBr:Eu2+ is capable of real-time, accurate, and precise measurement under SBRT conditions. The probe is smaller than a conventional dosimeter, has excellent spatial resolution, and can be valuable in SBRT with a steep dose distribution over a small field. The developed PSP dosimeter system appears to be suitable for in vivo SBRT dosimetry.

Large displacement haptic stimulus actuator using piezoelectric pump for wearable devices.

Recently, given Japan's aging society background, wearable healthcare devices have increasingly attracted attention. Many devices have been developed, but most devices have only a sensing function. To expand the application area of wearable healthcare devices, an interactive communication function with the human body is required using an actuator. For example, a device must be useful for medication assistance, predictive alerts of a disease such as arrhythmia, and exercise. In this work, a haptic stimulus actuator using a piezoelectric pump is proposed to realize a large displacement in wearable devices. The proposed actuator drives tactile sensation of the human body. The measurement results obtained using a sensory examination demonstrate that the proposed actuator can generate sufficient stimuli even if adhered to the chest, which has fewer tactile receptors than either the fingertip or wrist.

Influence of parasitic capacitance on output voltage for series-connected thin-film piezoelectric devices.

Series-connected thin film piezoelectric elements can generate large output voltages. The output voltage ideally is proportional to the number of connections. However, parasitic capacitances formed by the insulation layers and derived from peripheral circuitry degrade the output voltage. Conventional circuit models are not suitable for predicting the influence of the parasitic capacitance. Therefore we proposed the simplest model of piezoelectric elements to perform simulation program with integrated circuit emphasis (SPICE) circuit simulations). The effects of the parasitic capacitances on the thin-film Pb(Zr, Ti)O(3), (PZT) elements connected in series on a SiO(2) insulator are demonstrated. The results reveal the negative effect on the output voltage caused by the parasitic capacitances of the insulation layers. The design guidelines for the devices using series-connected piezoelectric elements are explained.

An annular mechanical temperature compensation structure for gas-sealed capacitive pressure sensor.

A novel gas-sealed capacitive pressure sensor with a temperature compensation structure is reported. The pressure sensor is sealed by Au-Au diffusion bonding under a nitrogen ambient with a pressure of 100 kPa and integrated with a platinum resistor-based temperature sensor for human activity monitoring applications. The capacitance-pressure and capacitance-temperature characteristics of the gas-sealed capacitive pressure sensor without temperature compensation structure are calculated. It is found by simulation that a ring-shaped structure on the diaphragm of the pressure sensor can mechanically suppress the thermal expansion effect of the sealed gas in the cavity. Pressure sensors without/with temperature compensation structures are fabricated and measured. Through measured results, it is verified that the calculation model is accurate. Using the compensation structures with a 900 µm inner radius, the measured temperature coefficient is much reduced as compared to that of the pressure sensor without compensation. The sensitivities of the pressure sensor before and after compensation are almost the same in the pressure range from 80 kPa to 100 kPa.

Self-calibrated humidity sensor in CMOS without post-processing.

A 1.1 µW power dissipation, voltage-output humidity sensor with 10% relative humidity accuracy was developed in the LFoundry 0.15 µm CMOS technology without post-processing. The sensor consists of a woven lateral array of electrodes implemented in CMOS top metal, a humidity-sensitive layer of Intervia Photodielectric 8023D-10, a CMOS capacitance to voltage converter, and the self-calibration circuitry.

A standard CMOS humidity sensor without post-processing.

A 2 µW power dissipation, voltage-output, humidity sensor accurate to 5% relative humidity was developed using the LFoundry 0.15 µm CMOS technology without post-processing. The sensor consists of a woven lateral array of electrodes implemented in CMOS top metal, a Intervia Photodielectric 8023-10 humidity-sensitive layer, and a CMOS capacitance to voltage converter.