Highly Porous Particles of Cellulose Derivatives for Advanced Applications.

А chemical modification of cellulose diacetate by phthalate and nitrate was performed to increase solubility in organic solvents and change the electrical properties. The role of substituents on the conductivity, permittivity, and polarizability of cellulose films is revealed. It has been shown that highly porous micro particles can be obtained from cellulose derivatives by a simple and technological freeze-drying method. The resulting micro sized aerogels have a predominantly spherical morphology and amorphous structure. Suspensions of porous particles of nitro- and phthalylated cellulose derivatives in silicone oil have an increased dielectric permittivity compared to cellulose diacetate particles. Produced particles are novel promising material with tunable electrical properties for advanced applications in composites, including for electrorheological fluids.

Effect of photoconversion conditions on the spectral and cytotoxic properties of photoconvertible fluorescent polymer markers.

Fluorescence labeling of cells is a versatile tool used to study cell behavior, which is of significant importance in biomedical sciences. Fluorescent photoconvertible markers based on polymer microcapsules have been recently considered as efficient and perspective ones for long-term tracking of individual cells. However, the dependence of photoconversion conditions on the polymeric capsule structure is still not sufficiently clear. Here, we have studied the structural and spectral properties of fluorescent photoconvertible polymeric microcapsules doped with Rhodamine B and irradiated using a pulsed laser in various regimes, and shown the dependence between the photoconversion degree and laser irradiation intensity. The effect of microcapsule composition on the photoconversion process was studied by monitoring structural changes in the initial and photoconverted microcapsules using X-ray diffraction analysis with synchrotron radiation source, and Fourier transform infrared, Raman and fluorescence spectroscopy. We demonstrated good biocompatibility of free-administered initial and photoconverted microcapsules through long-term monitoring of the RAW 264.7 monocyte/macrophage cells with unchanged viability. These data open new perspectives for using the developed markers as safe and precise cell labels with switchable fluorescent properties.

Porous Polylactide Microparticles as Effective Fillers for Hydrogels.

High-strength composite hydrogels based on collagen or chitosan-genipin were obtained via mixing using highly porous polylactide (PLA) microparticles with diameters of 50-75 µm and porosity values of over 98%. The elastic modulus of hydrogels depended on the filler concentration. The modulus increased from 80 kPa to 400-600 kPa at a concentration of porous particles of 12-15 wt.% and up to 1.8 MPa at a filling of 20-25 wt.% for collagen hydrogels. The elastic modulus of the chitosan-genipin hydrogel increases from 75 kPa to 900 kPa at a fraction of particles of 20 wt.%. These elastic modulus values cover a range of strength properties from connective tissue to cartilage tissue. It is important to note that the increase in strength in this case is accompanied by a decrease in the density of the material, that is, an increase in porosity. PLA particles were loaded with C-phycocyanin and showed an advanced release profile up to 48 h. Thus, composite hydrogels mimic the structure, biomechanics and release of biomolecules in the tissues of a living organism.

Chitosan Sponges for Efficient Accumulation and Controlled Release of C-Phycocyanin.

The paper proposed a new porous material for wound healing based on chitosan and C-phycocyanin (C-PC). In this work, C-PC was extracted from the cyanobacteria Arthrospira platensis biomass and purified through ammonium sulfate precipitation. The obtained C-PC with a purity index (PI) of 3.36 ± 0.24 was loaded into a chitosan sponge from aqueous solutions of various concentrations (250, 500, and 1000 mg/L). According to the FTIR study, chitosan did not form new bonds with C-PC, but acted as a carrier. The encapsulation efficiency value exceeded 90%, and the maximum loading capacity was 172.67 ± 0.47 mg/g. The release of C-PC from the polymer matrix into the saline medium was estimated, and it was found 50% of C-PC was released in the first hour and the maximum concentration was reached in 5-7 h after the sponge immersion. The PI of the released C-PC was 3.79 and 4.43 depending on the concentration of the initial solution.

Effect of Recombinant Spidroins Self-Assembly on Rheological Behavior of Their Dispersions and Structure of Electrospun Nanofibrous Materials.

The effect of primary amino acid sequence in recombinant spidroins on their spatial organization is crucial for the fabrication of artificial fibers and fibrous materials. This study focuses on the rheological properties of aqueous and alcoholic solutions of recombinant analogs of natural spidroins (rS1/9 and rS2/12), as well as the structure of their films and nanofibrous materials. Non-Newtonian flow behavior of aqueous solutions of these proteins was observed at certain concentrations in contrast to their solutions in hexafluoroisopropanol. The secondary structure of recombinant spidroins was addressed by IR spectroscopy, whereas their self-organization in various solvents was studied by AFM and cryo-TEM. The influence of the solvent on the structure and properties of the films and nanofibrous materials produced by electrospinning has been established.

Nonwoven Materials Produced by Melt Electrospinning of Polypropylene Filled with Calcium Carbonate.

Nowadays, polypropylene-based nonwovens are used in many areas, from filtration to medicine. One of the methods for obtaining such materials is melt electrospinning. In some cases, it is especially interesting to produce composite fibers with a high degree of filling. In this work, the influence of the filling degree of isotactic polypropylene with calcium carbonate on the structure and properties of nonwoven materials obtained by melt electrospinning was studied. It was shown that electrospinning is possible, even at a filler content of 50%, while the average diameter of the fibers increases with the growth in the content of calcium carbonate. The addition of sodium stearate significantly reduces the diameter of the fibers (from 10-65 to 2-10 microns) due to reducing viscosity and increasing the electrical conductivity of the melt. Wide-angle X-ray diffraction analysis and IR spectroscopy reveal that the initial polymer and composites are characterized by the presence of stable α-form crystals, while nonwovens show a predominance of smectic mesophase. The addition of calcium carbonate leads to an increase in the hydrophobicity of the composite films, the addition of sodium stearate results in a decrease of hydrophobicity, while all nonwovens demonstrate superhydrophobic properties.

Planar and 3D fibrous polyaniline-based materials for memristive elements.

The memristive elements constructed using polymers - polyaniline (PANI) and polyethyleneoxide (PEO) - could be assembled on planar thin films or on 3D fibrous materials. Planar conductive PANI-based materials were made using the Langmuir-Schaefer (LS) method, and the 3D materials - using the electrospinning method which is a scalable technique. We have analyzed the influence of PANI molar mass, natures of solvent and subphase on the crystalline structure, thickness and conductivity of planar LS films, and the influence of PANI molar mass and the PANI-PEO ratio on the morphological and structural characteristics of 3D fibrous materials.