RESUMEN
Turning waste into valuable products is one of the main challenges of the chemical industry. In this work, chitosan (CS), an abundant, low-cost, and non-toxic biopolymer derived from chitin, was reshaped into beads of ~3â mm. Their suitability as a support material for active phase catalyst materials was tested for a zirconium-based Metal-Organic Framework (MOF) with incorporated Pt, namely UiO-67-Pt. Its incorporation was investigated via two procedures: a one-pot synthesis (OPS) and a post-synthetic functionalization (PSF) synthesis method. Scanning electron microscopy (SEM) images show good UiO-67-Pt dispersion throughout the CS beads for the one-pot synthesized material (UiO-67-Pt-OPS@CS). However, this uniform dispersion was not observed for the post-synthetically functionalized material (UiO-67-Pt-PSF@CS). The success of the implementation of UiO-67-Pt was evaluated with ultraviolet-visible and infrared spectroscopy for both composite materials. Thermogravimetric analysis (TGA) reveals higher thermal stabilities for UiO-67-Pt-OPS@CS composite beads in comparison to pure CS beads, but not for UiO-67-Pt-PSF@CS. The study provides valuable insights into the potential of chitosan as a green, bead-shaped support material for MOFs, offering flexibility in their incorporation through different synthesis routes. It further contributes to the broader goal of the sustainable and eco-friendly design of a new generation of catalysts made from waste materials, which will be the topic of future studies.
RESUMEN
The strong metal-support interaction (SMSI) is a phenomenon observed in supported metal catalyst systems in which reducible metal oxide supports can form overlayers over the surface of active metal nanoparticles (NPs) under a hydrogen (H2) environment at elevated temperatures. SMSI has been shown to affect catalyst performance in many reactions by changing the type and number of active sites on the catalyst surface. Laboratory methods for the analysis of SMSI at the nanoparticle-ensemble level are lacking and mostly based on indirect evidence, such as gas chemisorption. Here, we demonstrate the possibility to detect and characterize SMSIs in Co/TiOx model catalysts using the laboratory X-ray standing wave (XSW) technique for a large ensemble of NPs at the bulk scale. We designed a thermally stable MoNx/SiNx periodic multilayer to retain XSW generation after reduction with H2 gas at 600°C. The model catalyst system was synthesized here by deposition of a thin TiOx layer on top of the periodic multilayer, followed by Co NP deposition via spare ablation. A partial encapsulation of Co NPs by TiOx was identified by analyzing the change in Ti atomic distribution. This novel methodological approach can be extended to observe surface restructuring of model catalysts in situ at high temperature (up to 1000°C) and pressure (≤3â mbar), and can also be relevant for fundamental studies in the thermal stability of membranes, as well as metallurgy.
RESUMEN
Although biomass-based alternatives for the manufacturing of bioplastic films are an important aspect of a more sustainable future, their physicochemical properties need to be able to compete with the existing market to establish them as a viable alternative. One important factor that is often neglected is the long-term stability of renewables-based functional materials, as they should neither degrade after a day or week, nor last forever. One material showing high potential in this regard, also due to its intrinsic biodegradability and antibacterial properties, is chitosan, which can form stable, self-standing films. We previously showed that green additives introduce a broad tunability of the chitosan-based material properties. In this work, we investigate the long-term stability and related degradation processes of chitosan-based bioplastics by assessing their physicochemical properties over 400â days. It was found that the film properties change similarly for samples stored in the fridge (4 °C, dark) as at ambient conditions (20 °C, light/dark cycles of the day). Additives with high vapor pressure, such as glycerol, evaporate and degrade, causing both brittleness and discoloration. In contrast, films with the addition of crosslinking additives, such as citric acid, show high stability also over a long time, bearing great preconditions for practical applications. This knowledge serves as a stepping-stone to utilizing chitosan as an alternative material for renewable-resourced bioplastic products.
RESUMEN
To switch to alternatives for fossil-fuel-based polymer materials, renewable raw materials from green resources should be utilized. Chitosan is such a material that is a strong, but workable derivative from chitin, obtained from crustaceans. However, various applications ask for specific plastic properties, such as certain flexibility, hardness and transparency. With different additives, also obtainable from green resources, chitosan-based composites in the form of self-supporting films, ranging from very hard and brittle to soft and flexible were successfully produced. The additives turned out to belong to one of three categories, namely linear, non-linear, or crosslinking additives. The non-linear additives could only be taken up to a certain relative amount, whereas the uptake of linear additives was not limited within the range of our experiments. Additives with multiple functional groups tend to crosslink chitosan even at room temperature in an acidic medium. Finally, it was shown that dissolving the chitosan in acetic acid and subsequently drying the matrix as a film results in reacetylation compared to the starting chitosan source, resulting in a harder material. With these findings, it is possible to tune the properties of chitosan-based polymer materials, making a big step towards application of this renewable polymer within consumer goods.
RESUMEN
Nanoplastics (NPs), small (<1â µm) polymer particles formed from bulk plastics, are a potential threat to human health and the environment. Orders of magnitude smaller than microplastics (MPs), they might behave differently due to their larger surface area and small size, which allows them to diffuse through organic barriers. However, detecting NPs in the environment and organic matrices has proven to be difficult, as their chemical nature is similar to these matrices. Furthermore, as their size is smaller than the (spatial) detection limit of common analytical tools, they are hard to find and quantify. We highlight different micro-spectroscopic techniques utilized for NP detection and argue that an analysis procedure should involve both particle imaging and correlative or direct chemical characterization of the same particles or samples. Finally, we highlight methods that can do both simultaneously, but with the downside that large particle numbers and statistics cannot be obtained.
Asunto(s)
Plásticos , Contaminantes Químicos del Agua , Humanos , Plásticos/análisis , Microplásticos , Contaminantes Químicos del Agua/químicaRESUMEN
Polyolefin catalysts are characterized by their hierarchically complex nature, which complicates studies on the interplay between the catalyst and formed polymer phases. Here, the missing link in the morphology gap between planar model systems and industrially relevant spherical catalyst particles is introduced through the use of a spherical cap Ziegler-type catalyst model system for the polymerization of ethylene. More specifically, a moisture-stable LaOCl framework with enhanced imaging contrast has been designed to support the TiCl4 pre-active site, which could mimic the behaviour of the highly hygroscopic and industrially used MgCl2 framework. As a function of polymerization time, the fragmentation behaviour of the LaOCl framework changed from a mixture of the shrinking core (i.e., peeling off small polyethylene fragments at the surface) and continuous bisection (i.e., internal cleavage of the framework) into dominantly a continuous bisection model, which is linked to the evolution of the estimated polyethylene volume and the fraction of crystalline polyethylene formed. The combination of the spherical cap model system and the used advanced micro-spectroscopy toolbox, opens the route for high-throughput screening of catalyst functions with industrially relevant morphologies on the nano-scale.
RESUMEN
The development of improved zeolite materials for applications in separation and catalysis requires understanding of mass transport. Herein, diffusion of single molecules is tracked in the straight and sinusoidal channels of the industrially relevant ZSM-5 zeolites using a combination of single-molecule localization microscopy and uniformly oriented zeolite thin films. Distinct motion behaviors are observed in zeolite channels with the same geometry, suggesting heterogeneous guest-host interactions. Quantification of the diffusion heterogeneities in the sinusoidal and straight channels suggests that the geometry of zeolite channels dictates the mobility and motion behavior of the guest molecules, resulting in diffusion anisotropy. The study of hierarchical zeolites shows that the addition of secondary pore networks primarily enhances the diffusivity of sinusoidal zeolite channels, and thus alleviating the diffusion limitations of microporous zeolites.
RESUMEN
The electrocatalytic carbon dioxide (CO2 ) reduction reaction (CO2 RR) into hydrocarbons is a promising approach for greenhouse gas mitigation, but many details of this dynamic reaction remain elusive. Here, time-resolved surface-enhanced Raman spectroscopy (TR-SERS) is employed to successfully monitor the dynamics of CO2 RR intermediates and Cu surfaces with sub-second time resolution. Anodic treatment at 1.55â V vs. RHE and subsequent surface oxide reduction (below -0.4â V vs. RHE) induced roughening of the Cu electrode surface, which resulted in hotspots for TR-SERS, enhanced time resolution (down to ≈0.7â s) and fourfold improved CO2 RR efficiency toward ethylene. With TR-SERS, the initial restructuring of the Cu surface was followed (<7â s), after which a stable surface surrounded by increased local alkalinity was formed. Our measurements revealed that a highly dynamic CO intermediate, with a characteristic vibration below 2060â cm-1 , is related to C-C coupling and ethylene production (-0.9â V vs. RHE), whereas lower cathodic bias (-0.7â V vs. RHE) resulted in gaseous CO production from isolated and static CO surface species with a distinct vibration at 2092â cm-1 .
RESUMEN
Metal-organic frameworks (MOFs) are a class of porous crystalline materials showing great potential for applications such as catalysis, gas storage, molecular separations, energy storage and drug delivery. The properties that render them interesting stem from their structure (e.g. morphology, porosity or metal coordination and geometry). Thus, gaining a deeper understanding strongly relies on the availability and adequate use of advanced characterization tools, which can interrogate MOFs under realistic synthesis as well as catalysis (or sorption) conditions. Herein, we present an overview of the various characterization techniques specifically suitable for the study on the underlying chemistry of the formation mechanisms and adsorption properties of three archetypal MOFs, namely MIL-100, ZIF-8 and HKUST-1. A section on using MOFs as supports for metal atoms or complexes that can be used for catalysis on the robust Zr6 nodes of UiO-66 or NU-1000, and the characterization techniques used thereof, is presented as well. In addition, we discuss recent developments on the application of nano-spectroscopic characterization for MOF thin-films and explore the potential of MOFs as model systems in catalysis. The conclusions and outlook provide future research possibilities in the field of MOF characterization.
RESUMEN
Surface-mounted metal-organic frameworks (SURMOFs) show promising behavior for a manifold of applications. As MOF thin films are often unsuitable for conventional characterization techniques, understanding their advantageous properties over their bulk counterparts presents a great analytical challenge. In this work, we demonstrate that MOFs can be grown on calcium fluoride (CaF2 ) windows after proper functionalization. As CaF2 is optically (in the IR and UV/Vis range of the spectrum) transparent, this makes it possible to study SURMOFs using conventional spectroscopic tools typically used during catalysis or gas sorption. Hence, we have measured HKUST-1 during the adsorption of CO and NO. We show that no copper oxide impurities are observed and also confirm that SURMOFs grown by a layer-by-layer (LbL) approach possess Cu+ species in paddlewheel confirmation, but 1.9 times less than in bulk HKUST-1. The developed methodology paves the way for studying the interaction of any adsorbed gases with thin films, not limited to MOFs, low temperatures, or these specific probe molecules, pushing the boundaries of our current understanding of functional porous materials.
RESUMEN
Nickel-molybdenum (Ni-Mo) alloys are well studied as highly effective electrocatalyst cathodes for water splitting. Understanding deactivation pathways is a key to improving the performance of these catalysts. In this study, inâ situ characterization by UV/Vis spectroscopy and AFM of the morphology and Mo leaching of an Ni-Mo electrocatalyst was performed with the goal of understanding the stability and related Mo leaching mechanism. Switching the potential towards higher overpotentials results in a nonlinear change in Mo leaching. Multiple processes are proposed to take place, such as a decrease in the extent of Mo oxidation at the cathode induced by more strongly reducing potentials, while simultaneously the increase in the local pH at the cathode due to the hydrogen evolution reaction causes more Mo leaching. The change in capacitance of these materials depends strongly on the change in surface composition and not only on the surface area. Inâ situ UV/Vis spectroscopy showed that Mo leaching is a continuous process over the course of 4â h of operation. Finally, the material was deposited on different substrates and the effect on Ni-Mo stability was studied. The substrate has a significant, albeit complex, influence on the stability and activity of Ni-Mo cathodes. In terms of stability in 1 m KOH, Ni-Mo was found to be best deposited on stainless steel substrates operated at low overpotentials, on which it showed nearly no change in capacitance and exhibited low Mo leaching.
RESUMEN
Self-assembling peptides are an exemplary class of supramolecular biomaterials of broad biomedical utility. Mechanistic studies on the peptide self-assembly demonstrated the importance of the oligomeric intermediates towards the properties of the supramolecular biomaterials being formed. In this study, we demonstrate how the overall yield of the supramolecular assemblies are moderated through subtle molecular changes in the peptide monomers. This strategy is exemplified with a set of surfactant-like peptides (SLPs) with different ß-sheet propensities and charged residues flanking the aggregation domains. By integrating different techniques, we show that these molecular changes can alter both the nucleation propensity of the oligomeric intermediates and the thermodynamic stability of the fibril structures. We demonstrate that the amount of assembled nanofibers are critically defined by the oligomeric nucleation propensities. Our findings offer guidance on designing self-assembling peptides for different biomedical applications, as well as insights into the role of protein gatekeeper sequences in preventing amyloidosis.
RESUMEN
Microporous polymer frameworks have attracted considerable attention to make novel separation layers owing to their highly porous structure, high permeability, and excellent molecular separation. This study concerns the fabrication and properties of thin melamine-based microporous polymer networks with a layer thickness of around 400â nm, supported on an α-alumina support and their potential use in organic solvent nanofiltration. The modified membranes show excellent solvent purification performances, such as n-heptane permeability as high as 9.2â L m-2 h-1 bar -1 in combination with a very high rejection of approximately 99 % for organic dyes with molecular weight of ≥457â Da. These values are higher than for the majority of the state-of-the-art membranes. The membranes further exhibit outstanding long-term operation stability. This work significantly expands the possibilities of using ceramic membranes in organic solvent nanofiltration.
RESUMEN
Metal-organic frameworks (MOFs) are a promising class of materials for many applications, due to their high chemical tunability and superb porosity. By growing MOFs as (thin-)films, additional properties and potential applications become available. Here, copper (II) 1,3,5-benzenetricarboxylate (Cu-BTC) metal-organic framework (MOF) thin-films are reported, which were synthesized by spin-coating, resulting in "nanowebs", that is, fiber-like structures. These surface-mounted MOFs (SURMOFs) were studied by using photoinduced force microscopy (PiFM) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). The optimal concentration of precursors (10â mm) was determined that resulted in chemically homogeneous, pure nanowebs. Furthermore, the morphology and (un)coordinated Cu sites in the web were tuned by varying the rotation speed of the spin-coating process. X-ray diffraction (XRD) analysis showed that rotation speeds ≥2000â rpm (with precursors in a water/ethanol solution) generate the catena-triaqua-µ-(1,3,5-benzenetricarboxylate)-copper(II), or Cu(BTC)(H2 O)3 coordination polymer. X-ray photoelectron spectroscopy (XPS) highlighted the strong decrease in number of (defective) Cu+ sites, as the nanowebs mainly consist of coordinated Cu2+ Lewis acid sites (LAS) and organic linker-linker, for example, hydrogen-bonding, interactions. Finally, the Lewis-acidic character of the Cu sites is illustrated by testing the films as catalysts in the isomerization of α-pinene oxide. The higher number of LAS (≥3000â rpm), result in higher campholenic aldehyde selectivity reaching up to 87.7 %. Furthermore, the strength of a combined micro- and spectroscopic approach in understanding the nature of MOF thin-films in a spatially resolved manner is highlighted.
RESUMEN
Water electrolysis to form hydrogen as a solar fuel requires highly effective catalysts. In this work, theoretical and experimental studies are performed on the activity and stability of Ni-Mo cathodes for this reaction. Density functional theory studies show various Ni-Mo facets to be active for the hydrogen evolution reaction, Ni segregation to be thermodynamically favorable, and Mo vacancy formation to be favorable even without an applied potential. Electrolyte effects on the long-term stability of Ni-Mo cathodes are determined. Ni-Mo is compared before and after up to 100â h of continuous operation. It is shown that Ni-Mo is unstable in alkaline media, owing to Mo leaching in the form of MoO4 2- , ultimately leading to a decrease in absolute overpotential. It is found that the electrolyte, the alkali cations, and the pH all influence Mo leaching. Changing the cation in the electrolyte from Li to Na to K influences the surface segregation of Mo and pushes the reaction towards Mo dissolution. Decreasing the pH decreases the OH- concentration and in this manner inhibits Mo leaching. Of the electrolytes studied, in terms of stability, the best to use is LiOH at pHâ 13. Thus, a mechanism for Mo leaching is presented alongside ways to influence the stability and make the Ni-Mo material more viable for renewable energy storage in chemical bonds.
RESUMEN
Facile fabrication of well-intergrown, oriented zeolite membranes with tunable chemical properties on commercially proven substrates is crucial to broadening their applications for separation and catalysis. Rationally determined electrostatic adsorption can enable the direct attachment of a b-oriented silicalite-1 monolayer on a commercial porous ceramic substrate. Homoepitaxially oriented, well-intergrown zeolite ZSM-5 membranes with a tunable composition of Si/Al=25-∞ were obtained by secondary growth of the monolayer. Intercrystallite defects can be eliminated by using Na+ as the mineralizer to promote lateral crystal growth and suppress surface nucleation in the direction of the straight channels, as evidenced by atomic force microscopy measurements. Water permeation testing shows tunable wettability from hydrophobic to highly hydrophilic, giving the potential for a wide range of applications.
RESUMEN
Bridging the gap in studying surface reactions, processes, and morphology and measuring at (catalytic) relevant conditions is crucial for our understanding of the working principles of porous crystalline materials. Scanning tunneling microscopy is limited because of the required conductivity of the sample, whereas atomic force microscopy (AFM) is often challenging in use owing to the physical mechanism underlying the technique. Herein, we report a tailor-made autoclave-inserted AFM, able to measure at â¼20â bar and â¼110 °C. First, we show the ability to obtain nanometer resolution on well-defined test samples at before-mentioned conditions. Second, to demonstrate the possibilities of analyzing morphological evolutions at elevated temperatures and pressures, we use this setup to measure the stability of a surface-anchored metal-organic framework (SURMOF) in-situ at pressures of 1-20â bar in the temperature range between 20 and 60 °C. It was found that the showcase HKUST-1 material has a good physical stability, as it is hardly damaged from exposure to pressures up to 20â bar. However, its thermal stability is weaker, as exposure to elevated T damaged the material by influencing the interaction between organic linker and metal cluster. In-situ measurements at elevated T also showed an increased mobility of the material when working at such conditions. Combining the strength of AFM at elevated T and p with ex-situ AFM and spectroscopic measurements on this MOF showcases an example of how porous materials can be studied at (industrially) relevant conditions using the autoclave-inserted AFM.
RESUMEN
Metal-organic framework (MOF) thin films show unmatched promise as smart membranes and photocatalytic coatings. However, their nucleation and growth resulting from intricate molecular assembly processes are not well understood yet are crucial to control the thin film properties. Here, we directly observe the nucleation and growth behavior of HKUST-1 thin films by real-time in situ AFM at different temperatures in a Cu-BTC solution. In combination with ex situ infrared (nano)spectroscopy, synthesis at 25 °C reveals initial nucleation of rapidly growing HKUST-1 islands surrounded by a continuously nucleating but slowly growing HKUST-1 carpet. Monitoring at 13 and 50 °C shows the strong impact of temperature on thin film formation, resulting in (partial) nucleation and growth inhibition. The nucleation and growth mechanisms as well as their kinetics provide insights to aid in future rational design of MOF thin films.
RESUMEN
Control over assembly, orientation, and defect-free growth of metal-organic framework (MOF) films is crucial for their future applications. A layer-by-layer approach is considered a suitable method to synthesize highly oriented films of numerous MOF topologies, but the initial stages of the film growth remain poorly understood. Here we use a combination of infrared (IR) reflection absorption spectroscopy and atomic force microscopy (AFM)-IR imaging to investigate the assembly and growth of a surface mounted MOF (SURMOF) film, specifically HKUST-1. IR spectra of the films were measured with monolayer sensitivity and <10â nm spatial resolution. In contrast to the common knowledge of LbL SURMOF synthesis, we find evidence for the surface-hindered growth and large presence of copper acetate precursor species in the produced MOF thin-films. The growth proceeds via a solution-mediated mechanism where the presence of weakly adsorbed copper acetate species leads to the formation of crystalline agglomerates with a size that largely exceeds theoretical growth limits. We report the spectroscopic characterization of physisorbed copper acetate surface species and find evidence for the large presence of unexchanged and mixed copper-paddle-wheels. Based on these insights, we were able to optimize and automatize synthesis methods and produce (100) oriented HKUST-1 thin-films with significantly shorter synthesis times, and additionally use copper nitrate as an effective synthesis precursor.