Protecting soymilk flavor and nutrients from photodegradation.

Five different packaging treatments were studied over a 36-day period to determine if they protected soymilk from photo-oxidation. Soymilk was packaged in high-density polyethylene (HDPE) bottles with and without light protective additives (LPA). Two controls [(1) no LPA (translucent appearance); (2) a light-protected control (foil overwrap over no LPA control)] and three LPA-containing treatments, Low (0.6% TiO2), Medium (1.3% TiO2), High (4.3% TiO2) were studied. Bottles were stored in a lighted refrigerated display case (average light intensity between 800 to 2200 lux; 3°C) for 36 days and evaluated weekly. Soymilk packaged in high LPA bottles was protected from developing light-oxidized off-flavors and odors for a minimum of 15 days. High LPA bottles provided protection for riboflavin and controlled development of photooxidative products for approximately 29 days.

Shelf Life Determination of Fresh Blueberries (Vaccinium corymbosum) Stored under Controlled Atmosphere and Ozone.

Fresh blueberries are commonly stored and transported by refrigeration in controlled atmospheres to protect shelf life for long periods of storage. Ozone is an antimicrobial gas that can extend shelf life and protect fruit from microbial contamination. Shelf life of fresh highbush blueberries was determined over 10-day storage in isolated cabinets at 4°C or 12°C under different atmosphere conditions, including air (control); 5% O2 : 15% CO2 : 80% N2 (controlled atmosphere storage (CAS)); and ozone gas (O3) 4 ppm at 4°C or 2.5 ppm at 12°C, at high relative humidity (90-95%). Samples were evaluated for yeast and molds growth, weight loss, and firmness. CAS and O3 did not delay or inhibit yeast and molds growth in blueberries after 10 days at both temperatures. Fruit stored at 4°C showed lower weight loss values compared with 12°C. Blueberries stored under O3 atmosphere showed reduced weight loss at 12°C by day 10 and loss of firmness when compared to the other treatments. Low concentrations of ozone gas together with proper refrigeration temperature can help protect fresh blueberries quality during storage.

Survival of Listeria monocytogenes on fresh blueberries (Vaccinium corymbosum) stored under controlled atmosphere and ozone.

Listeria monocytogenes is a foodborne pathogen that represents a high risk for consumers because it can grow under refrigeration conditions and can also develop acid tolerance. Fresh blueberries are hand-picked, packed, and transported under refrigeration without receiving a microbial inactivation treatment. The aim of this work was to study the survival of L. monocytogenes in fresh highbush blueberries stored at 4 or 12 °C under different controlled atmosphere conditions, including air (control); 5% O2, 15% CO2, 80% N2 (controlled atmosphere storage [CAS]); or ozone gas (O3), 4 ppm at 4 °C or 2.5 ppm at 12 °C, at high relative humidity (90 to 95%) for a total of 10 days. Fresh blueberries inside a plastic clamshell were spot inoculated with the bacteria and were stored at 4 or 12 °C in isolated cabinets under air, CAS, and O3 atmospheric conditions. Samples were evaluated on days 0, 1, 4, 7, and 10 for microbial growth using modified Oxford agar. CAS did not delay or inhibit L. monocytogenes growth in fresh blueberries after 10 days. O3 achieved 3- and 2-log reductions when compared with air treatment at 4 and 12 °C, respectively. Low concentrations of O3 together with proper refrigeration temperature can ensure product safety throughout transportation. O3 is a strong antimicrobial that safely decomposes to oxygen and water without leaving residues and can be used as an alternative method to prevent bacterial growth during a long transport period.

Enhancement of plant essential oils' aqueous solubility and stability using alpha and beta cyclodextrin.

Sodium benzoate has been shown to produce benzene in combination with ascorbic acid. This has led to research for safe alternatives from plant essential oils and parabens that have shown some antimicrobial activity, but many of these compounds exhibit poor solubility in aqueous solutions. Cyclodextrins can increase the solubility of many compounds. This work aimed to investigate the solubility of 23 plant essential oils and 4 parabens in water and an apple juice medium. Four of these compounds were chosen for their low aqueous solubility to determine if complexing the compound with α- and ß-cyclodextrin would increase solubility. Three of the complexes were dissolved in an acidified aqueous solution and then studied in glass and polyethylene terephthalate (PET) to determine if storage material would affect the stability. Solubility of the 27 compounds in distilled water ranged from 1.6 mg/L to 2460.6 mg/L and the solubility of 18 of the compounds decreased from 2.5 to 84.7% in apple juice medium (pH = 3.4, 12-13 °Brix). Complexation with cyclodextrin dramatically increased the solubility of the compounds, up to 10-fold. Packaging material had no effect on concentration of compounds present over 7 days. Cyclodextrins were able to increase solubility of these compounds to more suitable concentrations, and may lead to viable natural alternatives to sodium benzoate.

Cyclodextrin inclusion complex formation and solid-state characterization of the natural antioxidants alpha-tocopherol and quercetin.

Cyclodextrin (CD) complexation procedures are relatively simple processes, but these techniques often require very specific conditions for each individual guest molecule. Variations of the coprecipitation from aqueous solution technique were optimized for the CD complexation of the natural antioxidants alpha-tocopherol and quercetin. Solid inclusion complex products of alpha-tocopherol/beta-CD and quercetin/gamma-CD had molar ratios of 1.7:1, which were equivalent to 18.1% (w/w) alpha-tocopherol and 13.0% (w/w) quercetin. The molar reactant ratios of CD/antioxidant were optimized at 8:1 to improve the yield of complexation. The product yields of alpha-tocopherol/beta-CD and quercetin/gamma-CD complexes from their individual reactants were calculated as 24 and 21% (w/w), respectively. ATR/FT-IR, 13C CP/MAS NMR, TGA, and DSC provided evidence of antioxidant interaction with CD at the molecular level, which indicated true CD inclusion complexation in the solid state. Natural antioxidant/CD inclusion complexes may serve as novel additives in controlled-release active packaging to extend the oxidative stability of foods.

High pressures in combination with antimicrobials to reduce Escherichia coli O157:H7 and Salmonella Agona in apple juice and orange juice.

The effect of high pressure processing in conjunction with the chemical antimicrobials, dimethyl dicarbonate (DMDC), hydrogen peroxide, cinnamic acid, potassium sorbate, and sodium benzoate (NaB) on E. coli O157:H7 strain E009 and Salmonella enterica serovar Agona was investigated in apple juice and orange juice, respectively. Juices were inoculated with approximately 10(6) CFU/ml and subjected to pressures of 550 MPa (E. coli O157:H7 samples) and 400 MPa (Salmonella Agona samples) for 2 min at 6 degrees C (initial temperature). Populations of each pathogen were determined before pressurization, immediately after pressurization, and after samples had been held after treatment for 24 h at 4 degrees C. The most effective treatment for E. coli O157:H7, as determined by plating immediately after pressurization, was 125 ppm of DMDC, which caused a >4.98-log reduction. Other treatments that were significantly different from the sample with no added antimicrobial were 62.5 ppm of DMDC, 300 ppm of hydrogen peroxide, and 500 ppm of NaB, which produced 4.97-, 5.79-, and 3.91-log total reductions, respectively. After 24 h at 4 degrees C, E. coli O157:H7 was undetectable in all treatment groups (and controls). In samples inoculated with Salmonella, the most effective treatment was 62.5 ppm of DMDC, which produced a 5.96-log decrease immediately after pressure treatment. The results for 1,000 ppm of NaB, which produced a 3.26-log decrease, also were significantly different from those for the sample containing no antimicrobials. After 24 h at 4 degrees C, all samples with added antimicrobials had near or more than a 5-log total reduction of Salmonella Agona.

High-pressure resistance variation of Escherichia coli O157:H7 strains and Salmonella serovars in tryptic soy broth, distilled water, and fruit juice.

The effect of high pressure on the log reduction of six strains of Escherichia coli O157:H7 and five serovars of Salmonella enterica was investigated in tryptic soy broth, sterile distilled water, and commercially sterile orange juice (for Salmonella) and apple cider (for E. coli). Samples were subjected to high-pressure processing treatment at 300 and 550 MPa for 2 min at 6 degrees C. Samples were plated onto tryptic soy agar directly after pressurization and after being held for 24 h at 4 degrees C. At 300 MPa, little effect was seen on E. coli O157:H7 strains, while Salmonella serovars varied in resistance, showing reductions between 0.26 and 3.95 log CFU/ml. At 550 MPa, E. coli O157:H7 strains exhibited a range of reductions (0.28 to 4.39 log CFU/ml), while most Salmonella populations decreased beyond the detection limit (> 5-log CFU/ml reduction). The most resistant strains tested were E. coli E009 and Salmonella Agona. Generally, bacterial populations in fruit juices showed larger decreases than did populations in tryptic soy broth and distilled water. E. coli O157:H7 cultures held for 24 h at 4 degrees C after treatment at 550 MPa showed a significant log decrease as compared with cultures directly after treatment (P < or = 0.05), while Salmonella serovars did not show this significant decrease (P > 0.05). All Salmonella serovars tested in orange juice treated at 550 MPa for 2 min at 6 degrees C and held for 24 h showed a > 5-log decrease, while E. coli O157:H7 strains require a higher pressure, higher temperature, longer pressurization, or a chemical additive to achieve a 5-log decrease.

Effect of antioxidants on oxidative stability of edible fats and oils: thermogravimetric analysis.

Thermogravimetric analysis was used to determine the oxidative stability of various edible oils (olive oil, milkfat) and triacylglycerides (triolein, trilinolein), while the effect of natural (alpha-tocopherol, ascorbic acid) and synthetic antioxidants (butylated hydroxytoluene (BHT), butylated hydroxyanisole (BHA), and tertiary butyl hydroquinone were evaluated by addition to trilinolein. Oil resistance to oxidation was obtained by measuring the increase in sample weight due to the uptake of molecular oxygen, the temperature at maximum sample weight, and the temperature at the onset of oxidation. When comparing sample weight increase, trilinolein proved to be oxidatively less stable than triolein, olive oil, and milk fat, while triolein was less stable than olive oil and milk fat. Olive oil showed significantly higher stability than milkfat when comparing the temperature at the onset of oxidation. When comparing effectiveness of antioxidants, a combination of 0.01% BHA and 0.01% BHT increased trilinolein stability the most.

Inhibition of pathogens on fresh produce by ultraviolet energy.

Ultraviolet energy at a wavelength of 253.7 nm (UVC) was investigated for its bactericidal effects on the surface of Red Delicious apples, leaf lettuce and tomatoes inoculated with cultures of Salmonella spp. or Escherichia coli O157:H7. Inoculated samples were subjected to different doses ranging from 1.5 to 24 mW/cm(2) of UVC and enumerated on tryptic soy agar plus 0.05 g/l nalidixic acid to determine effective log reductions of microbial populations. UVC applied to apples inoculated with E. coli O157:H7 resulted in the highest log reduction of approximately 3.3 logs at 24 mW/cm(2). Lower log reductions were seen on tomatoes inoculated with Salmonella spp. (2.19 logs) and green leaf lettuce inoculated with both Salmonella spp. and E. coli O157:H7 (2.65 and 2.79, respectively). No significant statistical difference (p>0.05) was seen in the ability of UVC to inactivate a higher population of either Salmonella spp. or E. coli O157:H7 on the surface of green leaf lettuce. No significant difference was seen among the use of different doses applied to the surface of fresh produce for reduction of E. coli O157:H7 or Salmonella spp. (p>0.05). The use of UVC may prove to be beneficial in protecting the safety of fruits and vegetables in conjunction with Good Agricultural Practices and Good Manufacturing Practices.

Formation of natamycin:cyclodextrin inclusion complexes and their characterization.

Natamycin is a broad spectrum antimycotic with very low water solubility, which is used to extend the shelf life of shredded cheese products. beta-Cyclodextrin (beta-CD), hydroxypropyl beta-cyclodextrin (HP beta-CD), and gamma-cyclodextrin (gamma-CD) were found to form inclusion complexes with natamycin in aqueous solution. The increase in solubility of natamycin with added beta-CD was observed to be linear (type A(L) phase solubility diagram). The 1:1 stability constant of natamycin:beta-CD complex was estimated from its phase solubility diagram to be 1010 M(-1). The phase solubility diagrams of both gamma-CD and HP beta-CD exhibited negative deviation from linearity (type A(N) diagram) and, therefore, did not allow the estimation of binding constants. The water solubility of natamycin was increased 16-fold, 73-fold, and 152-fold with beta-CD, gamma-CD, and HP beta-CD, respectively. The natamycin:CD inclusion complexes resulted in in vitro antifungal activity nearly equivalent to that of natamycin in its free state.

Stability of natamycin and its cyclodextrin inclusion complexes in aqueous solution.

Aqueous solutions of natamycin and its beta-cyclodextrin (beta-CD), hydroxypropyl beta-cyclodextrin, and gamma-cyclodextrin (gamma-CD) inclusion complexes were completely degraded after 24 h of exposure to 1000 lx fluorescent lighting at 4 degrees C. After 14 days of storage in darkness at 4 degrees C, 92.2% of natamycin remained in active form. The natamycin:beta-CD complex and natamycin:gamma-CD complex were significantly more stable (p < 0.05) than natamycin in its free state in aqueous solutions stored in darkness at 4 degrees C. Clear poly(ethylene terephthalate) packaging with a UV light absorber allowed 85.0% of natamycin to remain after 14 days of storage under 1000 lx fluorescent lighting at 4 degrees C. Natamycin:cyclodextrin complexes can be dissociated for analysis in methanol/water/acetic acid, 60:40:5, v/v/v. Natamycin and its complexes in dissociated form were quantified by reverse phase HPLC with detection by photodiode array at 304 nm.

Effect of microorganism characteristics on leak size critical to predicting package sterility.

The effects of microorganism size and motility on the leak size critical to the sterility of a package, along with the imposed pressure required to initiate liquid flow for the critical leak size, were measured. Pseudomonas fragi Lacy-1052, Bacillus atrophaeus ATCC 49337, and Enterobacter aerogenes ATCC 29007 were employed to assess package sterility. One hundred twenty-six 7-mm-long microtubes with interior diameters of 5, 10, and 20 microm were used to simulate package defects. Forty-two solid microtubes were used as controls. No significant differences were found between sizes or motility statuses of test organisms with respect to loss of sterility as a result of microbial ingress into test cells with microtube interior diameters of 5, 10, and 20 microm (P > 0.05). Interactions between the initiation of liquid flow as a result of applied threshold pressures and sterility loss for test cells were significant (P < 0.05).

Comparative study of a semisynthetic derivative of natamycin and the parent antibiotic on the spoilage of shredded cheddar cheese.

A water-soluble N-alkyl semisynthetic derivative of natamycin was synthesized by the Michael addition reaction of the parent with an N-substituted malemide. A comparative study was carried out to investigate the effectiveness of the semisynthetic derivative and the parent antibiotic in suppressing mold growth on shredded Cheddar cheese stored in modified atmosphere packaging (MAP). The effects of 0-, 10-, and 20-ppm antimycotic treatments were examined. A 20-ppm natamycin treatment effectively suppressed visible mold growth (< 10(4) CFU/g) in MAP samples for up to 30 days after packages were opened. The performance of the 20-ppm semisynthetic derivative was similar to that of the 10-ppm natamycin treatment. For these treatments, visible mold growth did not occur in MAP samples until 20 days after packages were opened. These results indicate that the semisynthetic derivative of natamycin is less effective than the parent compound in suppressing mold growth on shredded Cheddar cheese.

Application of fluid modeling to determine threshold leak size for liquid foods.

In this study, the mechanism by which a package defect converts to a leaker was examined in an effort to develop a relationship between threshold leak size and loss of package sterility. The threshold leak size is the hole size at which the onset of leakage occurs. The threshold pressure is the pressure required to initiate a leak. Leak initiation was studied in terms of the interaction between three components: liquid attributes of liquid food products, defect size, and pressures required to initiate liquid flow. Liquid surface tension, viscosity, and density values were obtained for 16 liquids. The imposed pressures required to initiate flow through microtubes with interior diameters of 0, 2, 5, 7, 10, 20, and 50 microm were measured with the use of 63 test cells filled with safranin red dye, tryptic soy broth, and distilled water with surface tensions of 18.69, 44.09, and 64.67 mN/m, respectively. Significant differences (P<0.05) between threshold pressures observed for safranin red dye, tryptic soy broth, and distilled water were found. Liquids with low surface tensions, such as safranin red dye, required significantly lower threshold imposed pressures than did liquids with high surface tensions, such as distilled water (P<0.05). An equation to quantify the relationship between liquid surface tension, threshold imposed pressure, and defect size was developed. Threshold pressures observed were not significantly different (P>0.05) from those predicted by the equation. Imposed pressures and vacuums generated within packages during random vibration and sweep resonance tests were measured for brick-style aseptic packages (250 ml), metal cans (76.2 by 114.3 mm [425 ml]), 1-qt gable-top packages (946 ml), 0.5-gal gable-top packages (1.89 liters), and 1-gal milk jugs (4.25 liters). Significant differences between packages were found with respect to observed generated pressures during vibration testing (P<0.05). An equation to calculate threshold size on the basis of liquid surface tension and imposed pressure was established.

Response of Salmonella and Escherichia coli O157:H7 to UV energy.

To determine the efficacy of a UV light treatment at 253.7 nm (UVC light) on microbial growth, plates containing tryptic soy agar plus 50 ppm of nalidixic acid (TSAN) were inoculated with known concentrations of five-strain cocktails of Salmonella and Escherichia coli O157:H7 and subjected to different UVC treatments. The concentration of the cocktail inoculum was determined with TSAN prior to inoculation. Serial dilutions were carried out, and inoculation levels of 10(0) to 10(8) CFU/ ml were tested for each pathogen. Multiple replications of doses of UV light ranging from 1.5 to 30 mW/cm2 were applied to different cocktail concentrations, and doses of > 8.4 mW/cm2 resulted in a 5-log reduction of Escherichia coli O157:H7, while a 5-log reduction of Salmonella was observed with doses of > 14.5 mW/cm2. Results for both organisms yielded sigmoidal inactivation curves. UVC light is effective in reducing microbial populations of pathogens on agar surfaces.

Bioaerosol Exposure Method for Package Integrity Testing †.

Test organism motility, concentration, aerosol exposure time, hole diameter and length were evaluated to determine their influence on microbial ingress into a flexible plastic pouch. Microtubes with 10- and 20-µm hole diameters and of 5- and 10-mm lengths were used as defects in 128 flexible pouches. A bioaerosol with a 2.68-µm mean particle size comprised of 102 or 106 CFU/ml source concentrations of motile or nonmotile Pseudomonas fragi TM 849 was introduced into a 119,911-cm3 chamber for exposures of 15 or 30 minutes. Six pouches showed test organism growth after a 72-h incubation period. Microbial ingress was significant (P < .05) for motile test organisms with source concentrations of 106 CFU/ml.

Contamination of Flexible Pouches Challenged by Immersion Biotesting †.

Immersion biotesting has long been used to challenge packages, particularly cans, for pinholes and channel leaks. Such testing for all types of plastic packaging may not be appropriate because some packages (e.g., aseptic, hot fill) are not exposed to water. As the food-packaging industry develops alternative environmental biotests there is a need to benchmark them against traditional immersion testing. The purpose of this research was to examine the threshold of critical-defect dimensions using artifically created channel leaks of 10 and 20 µm and 5- and 10-mm lengths sealed into plastic pouches which were subsequently tested by immersion at 102 and 106 CFU of motile and nonmotile Pseudomonas fragi TM849 per ml. Forty-four percent (44%) of the pouches tested became contaminated, indicating the threshold defect value is below 10 µm. Microbial ingress was significant (P < .05) for motile test organisms with a concentration of 106 CFU/ml. The interaction of concentration and time was also significant at 102 CFU/ml at 30 min exposure and 106 CFU/ml at 15 min. Channel length was not statistically significant. The markedly greater contamination rate using immersion testing versus that of aerosol testing highlights the importance of using test methods that reflect environmental exposure conditions of the packages.