RESUMEN
Hard-facing as a type of the coating depositing is increasingly used today. Physical-chemical-metallurgical characteristics of contact layers in tribo-mechanical systems depend on the operating conditions and the conditions under which the work surfaces were created. That is the reason the influence of the processing procedures and regime, used in the contact surfaces formation, on development of the wear process of contact elements, is being considered ever more. To determine the influence of the hard-facing technology on characteristics of the gears' working surfaces, the experimental investigations were performed on samples hard-faced on the steel for cementation, by varying the filler metals (FM) and the hard-facing regimes. The samples tested were hard-faced by five "hard" and three "soft" filler metals. Experimental investigations included measuring the hard-faced layers' hardness and determination of their microstructure, as well as the wear resistance in the laboratory conditions, on tribometer and on a specially designed device for tests in the real operating conditions of gears. The wear intensity was monitored by the wear trace's width in the laboratory conditions and by the share of the teeth surfaces affected by the destructive pitting in the operating conditions. The results obtained were compared to results of the base metal (BM) tests, which provided the certain conclusions on which filler metal and which welding procedure are the optimal ones for regeneration of the worn teeth surfaces.
RESUMEN
Numerous phenomena that occur during the process of machine parts' regeneration have a significant impact on the loss of their working ability. Therefore, the properties of the working surfaces of the teeth flanks of repaired gears were analyzed in this research. The hereditary properties of the gear teeth are expressed by the interdependence of their geometric and physical-mechanical-metallurgical parameters created during the technological operations of regeneration of worn teeth by welding/hard-facing. The hard-facing was executed with three filler metal types, namely: combination Inox 18/8/6 + EDur 600, Castolin 2 and UTP 670. The tested properties included geometrical accuracy, microstructure and microhardness. Evaluation of the executed regeneration procedures was done by comparing the mentioned parameters of the regenerated gears and the new ones. The tested gears were not withdrawn from production due to damage, but they were newly manufactured and intentionally damaged gears, made of the same materials, subjected to the same manufacturing process. In this way, all influences except for the considered filler metal type were eliminated. Based on results of the conducted experiments, it was possible to establish the influence of the filler metal type on the surface characteristics of the regenerated gears' teeth flanks.
RESUMEN
This paper presents the results of voluminous experimental investigations conducted to analyze the influence of the welding procedure on the performance of regenerated gears. Cylindrical spur gears were tested, both newly manufactured and regenerated, in two fundamentally different ways: by hard facing (surfacing) with the "hard" filler metal (DUR 600-IG) and with the "soft" filler metal (EVB2CrMo) with subsequent cementation and quenching. The regeneration procedures were defined and executed, while, subsequently, the microstructure and microhardness of the hard-faced layers were established and measured, followed by checking the durability of the hard-faced teeth flanks. Finally, techno-economic analysis was performed to establish the rationality of the conducted regenerations, i.e., the costs of regenerated and newly manufactured teeth were compared. Based on the results of the conducted investigations, it was possible to establish the influence of the welding type on the performance characteristics (primarily the service life) of the regenerated gears. For individual reparatory hard facing, the procedure with the "hard" filler metal exhibited better characteristics, while for batch reparation of numerous damaged gears, the reparation with the "soft" filler metal, followed by cementation and heat treatment, might be more convenient.
RESUMEN
AIM: The purpose of this study was to develop a novel thiolated starch polymer with improved mucoadhesive properties by conjugation of cysteamine to starch as a natural polymer of restricted mucoadhesive properties. METHODS: Aldehyde substructures were integrated into starch via oxidative cleavage of vicinal diols by increasing amounts of sodium periodate followed by covalent attachment of cysteamine to oxidized starch via reductive amination. Thiol groups were quantified via Ellman's reaction and their impact on mucoadhesion was analyzed by rheological investigations, the rotating cylinder method and tensile studies on porcine mucosa. RESULTS: The total amount of immobilized thiol groups revealed a correlation between degree of oxidation and thiolation. Modified starch demonstrated an up to 1.66-fold increase in water uptake in comparison to native starch. Modification of starch resulted in greatly improved cohesive properties and improvement in mucoadhesion. Rheological investigations revealed a 2- to 4-fold rise in viscosity of mucus. Tensile studies revealed a linear correlation between degree of oxidation/thiolation and enhancement of maximum detachment force and total work adhesion. CONCLUSION: In terms of these results, thiolated starch is a new, promising, polymer in the field of mucoadhesive drug delivery systems.