RESUMEN
Tilted image series are acquired on liquid suspensions of latex particles supported by a carbon membrane. To do this, a home-made stage fitting in an Environmental Scanning Electron Microscope (ESEM) is optimized to minimize cold losses and thus improve both sample stability and spatial resolution in the images. As latex particles are electron-sensitive materials, sample degradation and stability are taken into account in the choice of the parameters for tilted image series acquisition. Despite the limited number of images, conventional algorithms are used to reconstruct the volume and study the three-dimensional arrangement of latex particles. The packing modes are in good agreement with what can be observed on frozen suspensions, although the domain sizes are smaller. Several quantitative parameters such as latex particle size and distance to first neighbors are extracted from the 3D model. Finally, the spatial resolution in the tomograms is estimated using Crowther criterion and by Fourier Shell Correlation analysis. It is also measured directly by analyzing a suspension containing latex particles and a surfactant of interest for composite formulation.
RESUMEN
Environmental scanning electron microscopy (ESEM) allows the observation of liquids under specific conditions of pressure and temperature. Moreover, when working in the transmission mode, that is in scanning transmission electron microscopy (STEM), nano-objects can be analysed inside a liquid. The contrast in the images is mass-thickness dependent as in STEM-in-TEM (transmission electron microscopy) using closed cells. However, in STEM-in-ESEM, as the liquid-vapour equilibrium is kept dynamically, the thickness of the water droplet remains unknown. In this paper, the contrasts measured in the experimental images are compared with calculations using Monte-Carlo simulations in order to estimate the thickness of water. Two examples are given. On gold nanoparticles, the thickness of a thick film can be estimated thanks to a contrast inversion. On core-shell latex particles, the grey level of the shell compared with those of the core and of the water film gives a relatively precise measurement of the water film thickness.
RESUMEN
For insulation applications, boards thinner than 2 cm are under design with specific thermal conductivities lower than 15 mW m-1 K-1 . This requires binding slightly hydrophobic aerogels which are highly nanoporous granular materials. To reach this step and ensure insulation board durability at the building scale, it is compulsory to design, characterise and analyse the microstructure at the nanoscale. It is indeed necessary to understand how the solid material is formed from a liquid suspension. This issue is addressed in this paper through wet-STEM experiments carried out in an Environmental Scanning Electron Microscope (ESEM). Latex-surfactant binary blends and latex-surfactant-aerogel ternary systems are studied, with two different surfactants of very different chemical structures. Image analysis is used to distinguish the different components and get quantitative morphological parameters which describe the sample architecture. The evolution of such morphological parameters during water evaporation permits a good understanding of the role of the surfactant.
RESUMEN
Intense visible nano-emitters are key objects for many technologies such as single photon source, bio-labels or energy convertors. Chalcogenide nanocrystals have ruled this domain for several decades. However, there is a demand for cheaper and less toxic materials. In this scheme, ZnO nanoparticles have appeared as potential candidates. At the nanoscale, they exhibit crystalline defects which can generate intense visible emission. However, even though photoluminescence quantum yields as high as 60% have been reported, it still remains to get quantum yield of that order of magnitude which remains stable over a long period. In this purpose, we present hybrid ZnO/polyacrylic acid (PAAH) nanocomposites, obtained from the hydrolysis of diethylzinc in presence of PAAH, exhibiting quantum yield systematically larger than 20%. By optimizing the nature and properties of the polymeric acid, the quantum yield is increased up to 70% and remains stable over months. This enhancement is explained by a model based on the hybrid type II heterostructure formed by ZnO/PAAH. The addition of PAAX (X = H or Na) during the hydrolysis of ZnEt2 represents a cost effective method to synthesize scalable amounts of highly luminescent ZnO/PAAX nanocomposites.
RESUMEN
Degenerate metal oxide nanoparticles are promising systems to expand the significant achievements of plasmonics into the infrared (IR) range. Among the possible candidates, Ga-doped ZnO nanocrystals are particularly suited for mid IR, considering their wide range of possible doping levels and thus of plasmon tuning. In the present work, we report on the tunable mid IR plasmon induced in degenerate Ga-doped ZnO nanocrystals. The nanocrystals are produced by a plasma expansion and exhibit unprotected surfaces. Tuning the Ga concentration allows tuning the localized surface plasmon resonance. Moreover, the plasmon resonance is characterized by a large damping. By comparing the plasmon of nanocrystal assemblies to that of nanoparticles dispersed in an alumina matrix, we investigate the possible origins of such damping. We demonstrate that it partially results from the self-organization of the naked particles and also from intrinsic inhomogeneity of dopants.
RESUMEN
Nanoindentation experiments inside a transmission electron microscope are of much interest to characterize specific phenomena occuring in materials, like for instance dislocation movements or phase transformations. The key points of these experiments are (i) the sample preparation and the optimization of its geometry to obtain reliable results and (ii) the choice of the transmission electron microscope observation mode, which will condition the type of information which can be deduced from the experiment. In this paper, we will focus on these two key points in the case of nanoindentation of zirconia, which is a ceramic material well known to be sensitive to stress because it can undergo a phase transformation. In this case, the information sought is the stress localization at the nanometre scale and in real time. As far as the sample preparation is concerned, one major drawback of nanoindentation inside a transmission electron microscope is indeed a possible bending of the sample occurring during compression, which is detrimental to the experiment interpretation (the stress is not uniaxial anymore). In this paper, several sample preparation techniques have been used and compared to optimize the geometry of the sample to avoid bending. The results obtained on sample preparation can be useful for the preparation of ceramics samples but can also give interesting clues and experimental approaches to optimize the preparation of other kinds of materials. The second part of this paper is devoted to the second key point, which is the determination of the stress localization associated to the deformation phenomena observed by nanoindentation experiments. In this paper, the use of convergent beam electron diffraction has been investigated and this technique could have been successfully coupled to nanoindentation experiments. Coupled nanoindentation experiments and convergent beam electron diffraction analyses have finally been applied to characterize the phase transformation of zirconia.
RESUMEN
This paper presents the development and the application of a new electron tomography technique based on STEM (Scanning Transmission Electron Microscopy) configuration in ESEM (Environmental Scanning Electron Microscopy). This combination provides a new approach for the characterization of the 3D structure of materials, as it optimizes a compromise between the resolution level of a few tens of nm and the large tomogram size due to the high thickness of transparency. The method is well adapted for non-conductive samples, and exhibits good contrast even for materials with low atomic number. The paper describes the development of a dedicated stage for this new tomography technique. Taking advantage of the size of the ESEM chamber, the range of tilt angles is not limited by the space around the sample. The performance of this device is illustrated through the three-dimensional characterization of samples issued from materials science and chosen to illustrate the results in resolution, contrast and thickness.
RESUMEN
This paper demonstrates the usefulness of pulsed laser ablation in liquids as a fast screening synthesis method able to prepare even complex compositions at the nanoscale. Nanoparticles of Y2O3:Eu3+, Lu2O2S:Eu3+, Gd2SiO5:Ce3+, Lu3TaO7:Gd3+ and Tb3+ are successfully synthesized by pulsed laser ablation in liquids. The phase and stoichiometries of the original materials are preserved while the sizes are reduced down to 5-10 nm. The optical properties of the materials are also preserved but show some small variations and some additional structures which are attributed to the specificities of the nanoscale (internal pressure, inhomogeneous broadening, surface states, etc).
RESUMEN
Polymer brushes consisting of polystyrene (PS) chains bonded covalently to N-doped multiwalled carbon nanotubes (CNx) were synthesized by a "grafting from" route using nitroxide mediated radical polymerization (NMRP).
