Analysis of naphthenic acids in produced water samples by capillary electrophoresis-mass spectrometry.

A capillary electrophoresis-mass spectrometry method was used to analyze naphthenic acids in produced water samples. It was possible to detect cyclopentanecarboxylic, benzoic, cyclohexanebutyric, 1-naphthoic, decanoic, 3,5-dimethyladamantane-1-carboxylic, 9-anthracenecarboxylic, and pentadecanoic acids within ca. 13 min using a buffer composed of 40 mmol/L ammonium hydroxide, 32 mmol/L acetic acid and 20% v/v isopropyl alcohol, pH 8.6. The proposed method showed good repeatability, with relative standard deviation (RSD) values of 6.6% for the sum of the peak areas and less than 2% for the analysis time. In the interday analysis, the RSD values for the sum of the peak areas and migration time were 10.3% and 10%, respectively. The developed method demonstrated linear behavior in the concentration range between 5 and 50 mg/L for benzoic, decanoic, 3,5-dimethyladamantane-1-carboxylic and 9-anthracenecarboxylic acids, and between 10 and 50 mg/L for cyclopentanecarboxylic, cyclohexanebutyric, 1- naphthoic, and pentadecanoic acids. The detection limits values ranged from 0.31 to 1.64 mg/L. Six produced water samples were analyzed and it was possible to identify and quantify cyclopentanecarboxylic, benzoic, cyclohexanebutyric, and decanoic acids. The concentrations varied between 4.8 and 98.9 mg/L, proving effective in the application of complex samples.

Quantitative Evaluation of Non-basic Nitrogen-Containing Compounds in Petroleum-Derived Samples by Direct Injection ESI (-) Orbitrap MS.

The quantification of non-basic nitrogen-containing compounds (NCCs) in petroleum-derived samples has become a critical issue due to the undesirable effects of these compounds on the petroleum industry. In addition, there is a lack of analytical methods that allow the direct quantification of NCCs in these matrices. This paper provides strategies for obtaining quantitative information of NCCs in petroleum-derived samples using direct flow injection electrospray ionization (ESI) (-) Orbitrap mass spectrometry without fractionation steps. Benzocarbazole (BC) quantification was performed using the standard addition method. The method was validated, and all analytical parameters demonstrated satisfactory results in the matrix-mix. Paired Student's t-test exhibited the matrix effect (95% confidence level, p < 0.05). Limits of detection ranged from 2.94 to 14.91 µg L-1, and the limits of quantification ranged from 9.81 to 49.69 µg L-1. Intraday and interday accuracy and precision were not above 15%. Quantification of non-basic NCCs was carried out based on two approaches. In approach 1, the non-basic NCCs' total content in petroleum-derived samples was determined by the BC concentration and the total abundance correction. The method presented good performance with the average error of 21, 8.3, and 28% for crude oil, gas oil, and diesel samples, respectively. Approach 2 was based on the multiple linear regression model with regression significant at a 0.05 significance level within average relative errors of 16, 7.8, and 17% for the crude oil, gas oil, and diesel samples, respectively. Then, both approaches successfully predicted the quantification of non-basic NCCs by ESI direct flow injection.

Separation of carbohydrates on electrophoresis microchips with controlled electrolysis.

This study reports the separation of fructose, galactose, glucose, lactose and sucrose on glass microchip electrophoresis (ME) devices using a microfluidic platform adapted with external reservoirs for controlling the electrolysis phenomenon. The connections between external reservoirs and microfluidic platform were performed by saline bridges created using silicone tubing filled with BGE. The separation conditions were optimized and the best results were achieved using a BGE containing 75 mmol/L NaOH and 15 mmol/L trisodium phosphate. Electrophoretic separations were monitored using a capacitively coupled contactless conductivity detection system. The controlled electrolysis has successfully allowed the application of a higher voltage on the separation channel promoting the baseline separation of five carbohydrates within 180 s with great run-to-run repeatability (RSD < 1%). The achieved efficiencies ranged from 45 000 ± 6000 to 70 000 ± 3000 plates/m demonstrating a performance better than ME devices without controlled electrolysis. The proposed system offered good linearity from 1 to 10 mmol/L and LODs between 150 and 740 µmol/L. The use of external tubes for controlling the electrolysis phenomenon on ME devices has solved common problems associated to run-to-run repeatability and analytical reliability required for routine and quantitative analysis.

High performance separation of quaternary amines using microchip non-aqueous electrophoresis coupled with contactless conductivity detection.

This study describes the development of an analytical methodology for the separation of quaternary amines using non-aqueous microchip electrophoresis (NAME) coupled with capacitively coupled contactless conductivity detection (C4D). All experiments were performed using a commercial microchip electrophoresis system consisting of a C4D detector, a high-voltage sequencer and a microfluidic platform to assemble a glass microchip with integrated sensing electrodes. The detection parameters were optimized and the best response was reached applying a 700-kHz sinusoidal wave with 14Vpp excitation voltage. The running electrolyte composition was optimized aiming to achieve the best analytical performance. The mixture containing methanol and acetonitrile at the proportion of 90:10 (v:v) as well as sodium deoxycholate provided separations of ten quaternary amines with high efficiency and baseline resolution. The separation efficiencies ranged from 8.7×104 to 3.0×105 plates/m. The proposed methodology provided linear response in the concentration range between 50 and 1000µmol/L and limits of detection between 2 and 27µmol/L. The analytical feasibility of the proposed methodology was tested in the determination of quaternary amines in corrosion inhibitor samples often used for coating oil pipelines. Five quaternary amines (dodecyltrimethylammonium chloride, tetradecyltrimetylammonium bromide, cetyltrimethylammonium bromide, tetraoctylammonium bromide and tetradodecylammonium bromide) were successfully detected at concentration levels from 0.07 to 6.45mol/L. The accuracy of the developed methodology was investigated and the achieved recovery values varied from 85 to 122%. Based on the reported data, NAME-C4D devices exhibited great potential to provide high performance separations of hydrophobic compounds. The developed methodology can be useful for the analysis of species that usually present strong adsorption on the channel inner walls.