RESUMEN
Atom probe tomography (APT)-based isotopic analyses are becoming increasingly attractive for analysis applications requiring small volumes of material and sub-micrometer length scales, such as isotope geochemistry, nuclear safety, and materials science. However, there is an open question within the atom probe community as to the reliability of atom probe isotopic and elemental analyses. Using our proposed analysis guidelines, in conjunction with an empirical calibration curve and a machine learning-based adaptive peak fitting algorithm, we demonstrate accurate and repeatable uranium isotopic analyses, via atom probe mass spectrometry, on U3O8 isotopic reference materials. By using isotopic reference materials, each measured isotopic abundance value could be directly compared to a known certified reference value to permit a quantitative statement of accuracy. The isotopic abundance measurements for 235U and 238U in each individual APT sample were consistently within ±1.5% relative to the known reference values. The accuracy and repeatability are approaching values consistent with measurements limited primarily by Poisson counting statistics, i.e., the number of uranium atoms recorded.
RESUMEN
Atom probe tomography (APT) can theoretically deliver accurate chemical and isotopic analyses at a high level of sensitivity, precision, and spatial resolution. However, empirical APT data often contain significant biases that lead to erroneous chemical concentration and isotopic abundance measurements. The present study explores the accuracy of quantitative isotopic analyses performed via atom probe mass spectrometry. A machine learning-based adaptive peak fitting algorithm was developed to provide a reproducible and mathematically defensible means to determine peak shapes and intensities in the mass spectrum for specific ion species. The isotopic abundance measurements made with the atom probe are compared directly with the known isotopic abundance values for each of the materials. Even in the presence of exceedingly high numbers of multi-hit detection events (up to 80%), and in the absence of any deadtime corrections, our approach produced isotopic abundance measurements having an accuracy consistent with values limited predominantly by counting statistics.
RESUMEN
In atom probe tomography (APT), some elements tend to field evaporate preferentially in multi-hit detection events. Boron (B) is one such element. It is thought that a large fraction of the B signal may be lost during data acquisition and is not reported in the mass spectrum or in the 3-D APT reconstruction. Understanding the relationship between the field evaporation behavior of B and the limitations for detecting multi-hit events can provide insight into the signal loss mechanism for B and may suggest ways to improve B detection accuracy. The present work reports data for nominally pure B and for B-implanted silicon (Si) (NIST-SRM2137) at dose levels two-orders of magnitude lower than previously studied by Da Costa, et al. in 2012. Boron concentration profiles collected from SRM2137 specimens qualitatively confirmed a signal loss mechanism is at work in laser pulsed atom probe measurements of B in Si. Ion correlation analysis was used to graphically demonstrate that the detector dead-time results in few same isotope, same charge-state (SISCS) ion pairs being properly recorded in the multi-hit data, explaining why B is consistently under-represented in quantitative analyses. Given the important role of detector dead-time as a signal loss mechanism, the results from three different methods of estimating the detector dead-time are presented. The findings of this study apply to all quantitative analyses that involve multi-hit data, but the dead-time will have the greatest effect on the elements that have a significant quantity of ions detected in multi-hit events.
RESUMEN
We have studied the influence of experimental factors and specimen geometry on the quality of the mass spectra in copper (Cu) during pulsed-laser atom-probe tomography. We have evaluated the effects of laser pulse energy, laser pulse frequency, specimen base temperature, specimen tip radius, and specimen tip shank half-angle on the effects of mass resolving power, (m/Δm), at full-width at half-maximum and at full-width at tenth-maximum, the tail size after the major mass-to-charge state (m/n) ratio peaks, and the mass spectra. Our results indicate that mass resolving power improves with decreasing pulse energy between 40 and 80 pJ and decreasing base temperature between 20 and 80 K. The mass resolving power also improves with increasing tip radius and shank half-angle. A pulse frequency of 250 kHz slightly improves the mass resolving power relative to 100 or 500 kHz. The tail size decreases with increasing pulse energy. The mass resolving power improves when the cooling time is reduced, which is influenced by the thermal diffusivity of Cu and the specimen base temperature.
RESUMEN
Electron channeling effects can create measurable signal intensity variations in all product signals that result from the scattering of the electron beam within a crystalline specimen. Of particular interest to the X-ray microanalyst are any variations that occur within the characteristic X-ray signal that are not directly related to a specimen composition variation. Many studies have documented the effect of crystallographic orientation on the local X-ray yield; however, the vast majority of these studies were carried out on thin foil specimens examined in transmission. Only a few studies have addressed these effects in bulk specimen materials, and these analyses were generally carried out at common scanning electron microscope microanalysis overvoltages (>1.5). At these overvoltage levels, the anomalous transmission effect is weak. As a result, the effect of electron channeling on the characteristic X-ray signal intensity has traditionally been overlooked in the field of quantitative electron probe microanalysis. The present work will demonstrate that electron channeling can produce X-ray variations of up to 26%, between intensity maxima and minima, in low overvoltage X-ray microanalyses of bulk specimens. Intensity variations of this magnitude will significantly impact the accuracy of qualitative and quantitative X-ray microanalyses at low overvoltage on engineering structural materials.