A finite element model for investigating the influence of keel design and position on unicompartmental knee replacement cementless tibial component fixation.

OBJECTIVES: The cementless Oxford Unicompartmental Knee Replacement (OUKR) tibial component relies on an interference fit to achieve initial fixation. The behaviour at the implant-bone interface is not fully understood and hence modelling of implants using Finite Element (FE) software is challenging. With a goal of exploring alternative implant designs with lower fracture risk and adequate fixation, this study aims to investigate whether optimisation of FE model parameters could accurately reproduce experimental results of a pull-out test which assesses fixation. MATERIALS AND METHODS: Finite element models of implants with three methods of fixation (standard keel, small keel, and peg) in a bone analogue foam block were created, in which implants were modelled using an analytical rigid definition and the foam block was modelled as a homogenous linear isotropic material. The total interference and elastic slip were varied in these models and optimised by comparing simulated and experimental results of pull-out tests for two (standard and peg) implant geometries. Then the optimised interference and elastic slip were validated by comparing simulated and experimental data of a third (small keel) implant geometry. RESULTS: The optimisation of parameters established an interference of 0.16 mm and an elastic slip of 0.20 mm as most suitable for modelling the experimental force-displacement plots during pull-out. This combination of parameters accurately reproduced the experimental results of the small keel geometry. The maximum pull-out forces from the FE models were consistent with experimental data for each implant design. CONCLUSIONS: This study shows that experimental pull-out tests can be accurately modelled using adjusted interference values and non-linear friction and outlines a method for determining these parameters. This study demonstrates that complex problems in modelling implant behaviour can be addressed with relatively simple models. This can potentially lead to the development of implants with reduced risk of failure.

Polyethylene bearing wear is comparable for cemented and cementless Oxford unicompartmental knee replacements: Ten-year results of a randomized controlled trial.

PURPOSE: There is concern that using cementless components may increase polyethylene wear of the Oxford unicompartmental knee replacement (OUKR). Therefore, this study aimed to measure bearing wear at 10 years in patients from a randomized trial comparing Phase 3 cemented and cementless OUKRs and to investigate factors that may affect wear. It was hypothesized that there would be no difference in wear rate between cemented and cementless OUKRs. METHODS: Bearing thickness was determined using radiostereometric analysis at postoperative, 3-month, 6-month, 1-year, 2-year, 5-year and 10-year timepoints. As creep occurs early, wear rate was calculated using linear regression between 6 months and 10 years for 39 knees (20 cemented, 19 cementless). Associations between wear and implant, surgical and patient factors were analysed. RESULTS: The linear wear rate of the Phase 3 OUKR was 0.06 mm/year with no significant difference (p = 0.18) between cemented (0.054 mm/year) and cementless (0.063 mm/year) implants. Age, Oxford Knee Score, component size and bearing thickness had no correlation with wear. A body mass index ≥ 30 was associated with a significantly lower wear rate (p = 0.007) as was having ≥80% femoral component contact area on the bearing (p = 0.003). Bearings positioned ≥1.5 mm from the tibial wall had a significantly higher wear rate (p = 0.002). CONCLUSIONS: At 10 years, the Phase 3 OUKR linear wear rate is low and not associated with the fixation method. To minimize the risk of wear-related bearing fracture in the very long-term surgeons should consider using 4 mm bearings in very young active patients and ensure that components are appropriately positioned, which is facilitated by the current instrumentation. LEVEL OF EVIDENCE: Level III, retrospective comparative study.

Mechanisms of mobile bearing dislocation in lateral unicompartmental knee replacement.

Mobile bearing dislocation occurs in 1- 6% of Oxford Domed Lateral replacements. Dislocations are predominantly medial, but can occur anteriorly or posteriorly. They tend to occur when the knee is flexed. It is not clear how dislocations can be prevented. A previously described mechanical rig for assessing mobile bearing dislocation was updated so as to study dislocation with the knee in flexion. Sub-categories for the description of each type of dislocation were introduced. Dislocation was only possible when the knee was distracted. As the amount of distraction possible in the knee is variable, the risk of dislocation is related to the amount of distraction in the rig necessary for a dislocation. The type of dislocation requiring the least distraction was medial `edge' dislocation in which the edge of the bearing dislocates onto the tibial wall, which is the most common type of dislocation. The amount of distraction necessary decreased the further the bearing was from the wall and with 50% posterior overhang. Rotation of the knee did not influence the amount of distraction. In conclusion dislocation can only occur if the lateral compartment is distracted. To reduce the dislocation risk, surgeons should aim to position the femoral and tibial components so that the bearing is as close as possible to the wall without jamming against it and the tibial component should be positioned flush with the posterior tibial cortex. If, during the surgery, the mobile bearing can easily be dislocated onto the wall the surgeon should consider changing to a fixed bearing. The tibial component should also be positioned flush with the posterior tibial cortex, as if it is too far forward this may contribute to dislocation.

Fixed lateral unicompartmental knee replacement is a reliable treatment for lateral compartment osteoarthritis after mobile-bearing medial unicompartmental replacement.

PURPOSE: Lateral osteoarthritis following medial unicompartmental knee replacement (UKR) is usually treated with total knee replacement, however, lateral UKR is a less invasive option that preserves a well-functioning medial UKR. This study aimed to determine the 5-year outcome of the cemented Fixed Lateral Oxford UKR (FLO) when used for the treatment of severe lateral disease after medial Oxford unicompartmental knee replacement. METHODS: Forty-four knees with lateral bone-on-bone osteoarthritis (n = 43) and avascular necrosis (n = 1) treated with the FLO following medial Oxford UKR were followed up prospectively. The Oxford Knee Score (OKS) and Tegner Activity Score (TAS) were collected pre- and post-operatively. Life-table analysis was used to determine survival rates. RESULTS: The mean patient age at the time of FLO surgery was 74.4 years with a mean time of 12.1 years between the primary medial UKR and the conversion to a bi-UKR with a FLO. Mean follow-up of the FLO was 3.5 years. After FLO no intra-operative or medical complications, re-admissions, or mortality occurred. There was one reoperation in which a bearing was exchanged for a medial bearing dislocation. There were no revisions of the FLO, so the FLO survival rate at 5 years was 100% (24 at risk). The mean pre-operative OKS was 22, which significantly (p < 0.0001) improved to a mean of 42, 42, and 40 at 1, 2, and 5 years, respectively. The median TAS had a non-significant improvement from 2.5 (Range 0-8) pre-operatively to 2 (Range 1-6) at 5 years postoperatively. CONCLUSION: The FLO is a reliable treatment for lateral osteoarthritis following medial UKR. At 5 years there was a 100% survival of the FLO with a mean OKS of 40. LEVEL OF EVIDENCE: IV, Prospective Case Series.

Incidence and severity of radiological lateral osteoarthritis 15 years following medial unicompartmental knee arthroplasty.

To assess the incidence of radiological lateral osteoarthritis (OA) at 15 years after medial unicompartmental knee arthroplasty (UKA) and assess the relationship of lateral OA with symptoms and patient characteristics. Cemented Phase 3 medial Oxford UKA implanted by two surgeons since 1998 for the recommended indications were prospectively followed. A 15-year cumulative revision rate for lateral OA of 5% for this series was previously reported. A total of 163 unrevised knees with 15-year (SD 1) anterior-posterior knee radiographs were studied. Lateral joint space width (JSWL) was measured and severity of lateral OA was classified as: nil/mild, moderate, and severe. Preoperative and 15-year Oxford Knee Scores (OKS) and American Knee Society Scores were determined. The effect of age, sex, BMI, and intraoperative findings was analyzed. Statistical analysis included one-way analysis of variance and Kruskal-Wallis H test, with significance set at 5%. The mean age was 80.6 years (SD 8.3), with 84 females and 79 males. The mean JSWL was 5.6 mm (SD 1.4), and was not significantly related to age, sex, or intraoperative findings. Those with BMI > 40 kg/m2 had a smaller JSWL than those with a 'normal' BMI (p = 0.039). The incidence of severe and moderate lateral OA were both 4.9%. Overall, 2/142 (1.4%) of those with nil/mild lateral OA, 1/8 (13%) with moderate, and 2/8 (25%) with severe subsequently had a revision. Those with severe (mean OKS 35.6 (SD 9.3)) and moderate OA (mean OKS 35.8 (SD 10.5)) tended to have worse outcome scores than those with nil/mild (mean OKS 39.5 (SD 9.2)) but the difference was only significant for OKS-Function (p = 0.044). This study showed that the rate of having severe or moderate radiological lateral OA at 15 years after medial UKA was low (both 4.9%). Although patients with severe or moderate lateral OA had a lower OKS than those with nil/mild OA, their mean scores (OKS 36) would be classified as good.

Application of a robotics path planning algorithm to assess the risk of mobile bearing dislocation in lateral unicompartmental knee replacement.

Due to ligament laxity, bearing dislocation occurs in 1-6% of Oxford Domed Lateral (ODL) replacements with most dislocations occurring medially. Dislocations were studied using a previously built mechanical rig, however testing using the rig was inefficient. The aim of this study was to develop a better tool that was more reliable and efficient. An established robotics software package, the Open Motion Planning Library, was modified to accept the ODL components. Using a robotics path planning algorithm, the mobile bearing was allowed to find a way out from between the femoral and tibial components i.e. to dislocate. Testing assessed a range of clinically relevant positions of the femoral component relative to the tibial component. Dislocations were labelled as medial, lateral, anterior or posterior depending on the dislocation direction. The Distraction to Dislocation (DD) measured the minimum vertical distraction of the femoral component from the tibial component for a dislocation to occur. Results were validated against the mechanical rig. Statistical analysis of medial dislocation showed excellent agreement with an intraclass correlation value of 0.993 (95% CI 0.982-0.998). All DDs from the dislocation analysis tool were within 1 mm of the mechanical rig DDs with results sharing a remarkably similar trend. The robotics dislocation analysis tool output DDs which were marginally higher than the manual mechanical rig: 0.50 mm anteriorly, 0.25 mm posteriorly and 0.50 mm laterally. Medially, the computational DD differed on average by 0.09 mm (stand deviation: 0.2026 mm). Our study describes the development and validation of a novel robotics dislocation analysis tool, which allows mobile bearing dislocation risk quantification. The tool may also be used to improve surgical implantation parameters and to assess new implant designs that aim to reduce the medial dislocation risk to an acceptable level.

The Oxford Domed Lateral Unicompartmental Knee Replacement implant: Increasing wall height reduces the risk of bearing dislocation.

Due to lateral ligament laxity, bearing dislocation occurs in 1%-6% of Oxford Domed Lateral replacements. Most dislocations are medial but they do rarely occur anteriorly or posteriorly. The aim was to decrease the risk of dislocation. For a bearing to dislocate the femoral component has to be distracted from the tibial component. A robotic-path-planning-algorithm was used with a computer model of the implant in different configurations to determine the Vertical Distraction needed for Dislocation (VDD). With current components, VDD anteriorly/posteriorly was 5.5 to 6.5 mm and medially was 3.5 to 5.75 mm. A thicker bearing increased VDD medially and decreased VDD anteriorly/posteriorly (0.1 mm/1 mm thickness increase). VDD medially increased with the bearing closer to the tibial wall (0.5 mm/1 mm closer), or by increasing the tibial wall height (1 mm/1 mm height increase). VDD anteriorly/posteriorly was not influenced by bearing position or wall height. To prevent collision between the femoral and tibial components an increase in wall height must be accompanied by a similar increase in minimum bearing thickness. Increasing the wall height and minimum bearing thickness by 2 mm and ensuring the bearing is 4 mm or less from the wall increased the minimum VDD medially to 5.5 mm. The lower VDD medially than anteriorly/posteriorly explains why medial dislocation is more common. If the wall height is increased by 2 mm, the minimum bearing thickness is 5 mm and the surgeon ensured the bearing is 4 mm or less from the wall, the medial dislocation rate should be similar to the anterior/posterior dislocation rate, which should be acceptable.

Systematic review and meta-analysis of bearing dislocation in lateral meniscal bearing unicompartmental knee replacement: Domed versus flat tibial surface.

BACKGROUND: Bearing dislocation is a problem following mobile bearing Oxford lateral Unicompartmental Knee Replacement (UKR). Therefore, the design of the tibial component was changed from a flat tibial surface to a domed tibial surface with a biconcave bearing to increase bearing entrapment. This systematic review compared the dislocation and revision rates of the two designs. METHODS: Two authors independently searched MEDLINE, EMBASE and ISI Web of Science, reference lists of retrieved articles, and the internet. Randomised, cohort, case-control and case studies of adult patients with lateral knee osteoarthritis treated with flat or domed Oxford lateral UKR and their outcomes were included. The overall dislocation rate and the annual revision rate (per 100 component years) were determined. RESULTS: Nine studies (937 knees) met the inclusion criteria (3 flat, 6 domed). Four studies (all domed) had a low risk of bias and five had a high risk (3 flat, 2 domed), so data should be interpreted with caution. The bearing dislocation rate decreased from 17% (flat) to 3.7% (domed). Dislocations occurred on average at 16 months and medial dislocations were most common. The revision rate excluding dislocation decreased from 1.1%pa to 0.7%pa. PROSPERO registration: CRD42019139250. CONCLUSION: Modifying the tibial component from a flat to a domed shape decreased the bearing dislocation rate to 3.7% and increased the 10 year survival rate excluding dislocation to 93%. The dislocation rate is still relatively high so bearing stability should be assessed intra-operatively and if unacceptable, a fixed bearing version of the Oxford lateral tibial component can be inserted.

The effect of obesity on revision rate in unicompartmental knee arthroplasty: a systematic review and meta-analysis.

The number of patients with knee osteoarthritis, the proportion that is obese and the number undergoing unicompartmental knee arthroplasty (UKA) are all increasing. The primary aim of this systematic review was to determine the effects of obesity on outcomes in UKA. A systematic review was performed using PRISMA guidelines and the primary outcome was revision rate per 100 observed component years, with a BMI of ≥ 30 used to define obesity. The MINORS criteria and OCEBM criteria were used to assess risk of bias and level of evidence, respectively. 9 studies were included in the analysis. In total there were 4621 knees that underwent UKA. The mean age in included studies was reported to be 63 years (mean range 59.5-72 years old)) and range of follow up was 2-18 years. Four studies were OCEBM level 2b and the average MINORS score was 13. The mean revision rate in obese patients (BMI > 30) was 0.33% pa (95% CI - 3.16 to 2.5) higher than in non-obese patients, however this was not statistically significant (p = 0.82). This meta-analysis concludes that there is no significant difference in outcomes between obese and non-obese patients undergoing UKA. There is currently no evidence that obesity should be considered a definite contraindication to UKA. Further studies are needed to increase the numbers in meta-analysis to explore activity levels, surgeon's operative data, implant design and perioperative complications and revision in more depth.Level of evidence Level III.

Low polyethylene creep and wear following mobile-bearing unicompartmental knee replacement.

PURPOSE: The Oxford unicompartmental knee replacement (UKR) has a fully congruent mobile bearing to minimise wear. However, with younger higher demand patients, wear remains a concern. The aim of this study was to quantify the wear rate of Phase 3 Oxford UKR bearings over the course of 5 years and to identify the factors that influence it. METHODS: 40 medial Oxford UKRs recruited for a randomised study of cemented and cementless fixation were studied with Radiostereometric analysis (RSA) at 1 week, 3 months, 6 months, 1 year, 2 years, and 5 years post-operatively and bearing thickness was calculated. Penetration, defined as the change in thickness compared to the 1-week measurement, was determined. Creep (early penetration) and wear (late penetration at a constant rate) were calculated. The influence of demographic factors, Oxford Knee Score (OKS), Tegner score, fixation and bearing overhang (determined by RSA) on wear was analysed. RESULTS: After 6 months the penetration rate was constant, indicating that wear alone was occurring. The wear rate was 0.07 mm/year (SD 0.03). The creep was 0.06 mm with about 95% occurring during the first 3 months. There was no significant relationship between fixation (cemented/cementless), age, component size, OKS and Tegner score with wear rate. Increasing BMI was associated with decreasing wear (p = 0.042). 37/40 bearings overhung the tibia to some extent and 23/40 overhung the tibia medially. An increase in the area of overhang (p = 0.036), amount of medial overhang (p = 0.028) and distance between the bearing and tibial wall (p = 0.019) were associated with increased wear. Bearings that did not overhang (0.06 mm/year) had less wear (p = 0.025) than those that did (0.08 mm/year). There was no relationship (p = 0.6) between the femoral contact area and wear. CONCLUSION: During the first three to six months after implantation, the bearing becomes 0.06 mm thinner due to creep. The combined wear rate of the upper and lower surfaces of the bearing is constant (0.07 mm/year). The wear is lower if the bearing does not overhang the tibia so surgeons should aim for the bearing to be close to the tibial wall. The orientation of the femoral component does not influence wear. LEVEL OF EVIDENCE: Retrospective Study, Level III.

Cementless unicompartmental knee replacement achieves better ten-year clinical outcomes than cemented: a systematic review.

PURPOSE: The aim of this study was to report and compare the long-term revision rate, revision indications and patient reported outcome measures of cemented and cementless unicompartmental knee replacements (UKR). METHODS: Databases Medline, Embase and Cochrane Central of Controlled Trials were searched to identify all UKR studies reporting the ≥ 10 year clinical outcomes. Revision rates per 100 component years [% per annum (% pa)] were calculated by fixation type and then, subgroup analyses for fixed and mobile bearing UKRs were performed. Mechanisms of failure and patient reported outcome measures are reported. RESULTS: 25 studies were eligible for inclusion with a total of 10,736 UKRs, in which there were 8790 cemented and 1946 cementless knee replacements. The revision rate was 0.73% pa (CI 0.66-0.80) and 0.45% pa (CI 0.34-0.58) per 100 component years, respectively, with the cementless having a significantly (p < 0.001) lower overall revision rate. Therefore, based on these studies, the expected 10-year survival of cementless UKR would be 95.5% and cemented 92.7%. Subgroup analysis revealed this difference remained significant for the Oxford UKR (0.37% pa vs 0.77% pa, p < 0.001), but for non-Oxford UKRs there were no significant differences in revision rates of cemented and cementless UKRs (0.57% pa vs 0.69% pa, p = 0.41). Mobile bearing UKRs had significantly lower revision rates than fixed bearing UKRs in cementless (p = 0.001), but not cemented groups (p = 0.13). Overall the revision rates for aseptic loosening and disease progression were significantly lower (p = 0.02 and p = 0.009 respectively) in the cementless group compared to the cemented group (0.06 vs 0.13% pa and 0.10 vs 0.21% pa respectively). CONCLUSIONS: Cementless fixation had reduced long-term revision rates compared to cemented for the Oxford UKR. For the non-Oxford UKRs, the revision rates of cementless and cemented fixation types were equivalent. Therefore, cementless UKRs offer at least equivalent if not lower revision rates compared to cemented UKRs. LEVEL OF EVIDENCE: III.

Oxford domed lateral unicompartmental knee arthroplasty.

AIMS: To report mid- to long-term results of Oxford mobile bearing domed lateral unicompartmental knee arthroplasty (UKA), and determine the effect of potential contraindications on outcome. METHODS: A total of 325 consecutive domed lateral UKAs undertaken for the recommended indications were included, and their functional and survival outcomes were assessed. The effects of age, weight, activity, and the presence of full-thickness erosions of cartilage in the patellofemoral joint on outcome were evaluated. RESULTS: Median follow-up was seven years (3 to 14), and mean age at surgery was 65 years (39 to 90). Median Oxford Knee Score (OKS) was 43 (interquartile range (IQR) 37 to 47), with 260 (80%) achieving a good or excellent score (OKS > 34). Revisions occurred in 34 (10%); 14 (4%) were for dislocation, of which 12 had no recurrence following insertion of a new bearing, and 12 (4%) were revised for medial osteoarthritis (OA). Ten-year survival was 85% (95% confidence interval (CI) 79 to 90, at risk 72). Age, weight, activity, and patellofemoral erosions did not have a significant effect on the clinical outcome or survival. CONCLUSION: Domed lateral UKA provides a good alternative to total knee arthroplasty (TKA) in the management of lateral compartment OA. Although dislocation is relatively easy to treat successfully, the dislocation rate of 4% is high. It is recommended that the stability of the bearing is assessed intraoperatively. If the bearing can easily be displaced, the fixed rather than the mobile bearing version of the Oxford lateral tibial component should be inserted instead. Younger age, heavier weight, high activity, and patellofemoral erosions did not detrimentally affect outcome, so should not be considered contraindications. Cite this article: Bone Joint J 2020;102-B(8):1033-1040.

Candidacy for medial unicompartmental knee replacement declines with age.

BACKGROUND: The effect of age on the percentage of primary knee replacements appropriate for unicompartmental replacement (UKR), defined as candidacy, is unknown. The aim was to determine the candidacy and outcome of UKR in different age groups. HYPOTHESIS: Age is associated with candidacy for medial UKR. PATIENTS AND METHODS: This cross-sectional study determined UKR candidacy from preoperative radiographs, including stress views, from 457 consecutive knee replacements (TKR or UKR) in a specialist joint replacement centre. Candidacy, estimated from radiographs and from usage, was determined for all knees and then stratified by age group<50, 50-60, 60-70, 70-80, and 80+. The outcome of UKR implanted in these groups was also assessed. To avoid overestimating, candidacy estimated by usage was used for the primary analysis. RESULTS: Candidacy decreased with age (OR 0.98, p=0.008) and was 61% (CI 42-78), 52% (CI 43-61), 43% (CI 35-51), 41% (CI 31-52), and 36% (CI 22-52) respectively. Candidacy estimated by radiographs was slightly higher overall (49% compared to 46%) and in all age groups than candidacy estimated from usage. Neither functional outcome (p=0.47) nor implant survival (p=0.54) was affected by age. Overall 80% achieved good/excellent Knee Society objective scores, and the five-year implant survival was 99%. DISCUSSION: There is a strong association of candidacy for UKR with age in that younger patients are more likely to be candidates (61% in those<50 and 36% in those 80+). Good outcomes can be expected in patients of all ages who are appropriate for UKR. LEVEL OF EVIDENCE: IV, Prognostic cross-sectional study.

Most unicompartmental knee replacement revisions could be avoided: a radiographic evaluation of revised Oxford knees in the National Joint Registry.

PURPOSE: The purpose of this study was to understand why the revision rate of unicompartmental knee replacement (UKR) in the National Joint Registry (NJR) is so high. Using radiographs, the appropriateness of patient selection for primary surgery, surgical technique, and indications for revision were determined. In addition, the alignment of the radiographs was assessed. METHODS: Oxford UKR registered with the NJR between 2006 and 2010 and subsequently revised were identified by the NJR. A blinded review was undertaken of pre-primary, post-primary, and pre-revision anteroposterior and lateral radiographs of a sample of 107 cases from multiple centres. RESULTS: The recommended indications were satisfied in 70%, with 29% not demonstrating bone-on-bone arthritis. Major technical errors, likely leading to revision, were seen in 6%. Pre-revision radiographs were malaligned and, therefore, difficult to interpret in 53%. No reason for revision was seen in 67%. Reasons for revision included lateral compartment arthritis (10%), tibial loosening (7%), bearing dislocation (7%), infection (6%), femoral loosening (3%), and peri-prosthetic fracture (2%, one femoral, one tibial). CONCLUSIONS: Only 20% of the revised UKR were implanted for the recommended indications, using appropriate surgical technique and had a mechanical problem necessitating revision. One-third of primary surgeries were undertaken in patients with early arthritis, which is contraindicated. Two-thirds were presumably revised for unexplained pain, which is not advised as it tends not to help the pain. This study suggests that variable and inappropriate indications for primary and revision surgery are responsible for the high rates of revision seen in registries. LEVEL OF EVIDENCE: III, Therapeutic study.

The clinical outcomes of cementless unicompartmental knee replacement in patients with reduced bone mineral density.

BACKGROUND: Osteoporosis and osteopenia are conditions characterised by reduced bone mineral density (BMD). There is concern that bone with reduced BMD may not provide sufficient fixation for cementless components which primarily rely on the quality of surrounding bone. The aim of our study was to report the midterm clinical outcomes of patients with reduced BMD undergoing cementless unicompartmental knee replacements (UKR). Our hypothesis was that there would be no difference in outcome between patients with normal bone and those with reduced BMD. METHODS: From a prospective cohort of 70 patients undergoing cementless UKR surgery, patients were categorised into normal (n = 20), osteopenic (n = 38) and osteoporotic groups (n = 12) based on their central dual-energy X-ray absorptiometry (DEXA) scans according to the World Health Organization criteria. Patients were followed up by independent research physiotherapists and outcome scores; Oxford Knee Score (OKS), Tegner score, American Knee Society Score Functional (AKSS-F) and Objective (AKSS-O) were recorded preoperatively and at a mean of 4 years postoperatively. The prevalence of reoperations, revisions and mortality was also recorded at a mean of 5 years postoperatively. RESULTS: There were no significant differences in the midterm postoperative OKS (P = 0.83), Tegner score (P = 0.17) and AKSS-O (P = 0.67). However, the AKSS-F was significantly higher (P = 0.04) in normal (90, IQR 37.5) compared to osteoporotic (65, IQR 35) groups. There were no significant differences (P = 0.82) between normal and osteopenic bone (80, IQR 35). The revision prevalence was 5%, 2.6% and 0% in the normal, osteopenic and osteoporotic groups respectively. The reoperation prevalence was 5%, 7.9% and 0% respectively. There were no deaths in any group related to the implant. CONCLUSIONS: We found that patients with reduced BMD could safely undergo cementless UKR surgery and have similar clinical outcomes to those with normal BMD. However, larger studies with longer follow-up are needed to confirm our findings and ensure that cementless fixation is safe in patients with reduced BMD.

Ten-year clinical and radiographic results of 1000 cementless Oxford unicompartmental knee replacements.

PURPOSE: Unicompartmental knee replacement (UKR) has substantial benefits over total knee replacement (TKR) but has higher revision rates. The cementless Oxford UKR was introduced to address this but there are concerns about fixation and tibial plateau fractures. The first long-term study of the device with clinical and radiographic outcomes is reported. METHODS: The first 1000 medial cementless Oxford UKR were prospectively identified and followed up by independent physiotherapists. Survival was calculated using the endpoints reoperation, revision, revision to TKR, major revision requiring revision TKR components and patient mortality. The Oxford Knee Score (OKS), Tegner Activity Score and American Knee Society Score (AKSS) were recorded and radiographs analysed. RESULTS: The ten year survival was 96.6% (CI 94.8-97.8), 97.5% (CI 95.7-98.5), 98.9% (CI 97.7-99.4) and 99.6% (CI 98.8-99.9) using reoperation, revision, revision to TKR and major revision as the endpoint, respectively. Commonest causes for revision were bearing dislocation (n = 7, 0.7%), disease progression (n = 4, 0.4%) and pain (n = 2, 0.2%). There was one lateral tibial plateau fracture and one femoral component loosening. At 10 years, the mean OKS was 41.2 (SD 9.8), Tegner 2.8 (SD 1.3), AKSS-O 89.1 (SD 13.0) and AKSS-F 80.4 (SD 14.6). There were no pathological radiolucencies or complete radiolucent lines. There were no implant-related deaths. CONCLUSIONS: The cementless Oxford UKR is a safe procedure with excellent long-term clinical results. Our results suggest that reliable fixation was achieved with only one (0.1%) revision for loosening (femoral), no radiographic evidence of loosening in the remaining cases and no fractures related to implantation. LEVEL OF EVIDENCE: III.

Long-term in vivo wear of different bearing types used for the Oxford Unicompartmental Knee Replacement.

OBJECTIVES: The aim of this study was to determine the polyethylene wear rate of Phase 3 Oxford Unicompartmental Knee Replacement bearings and to investigate the effects of resin type and manufacturing process. METHODS: A total of 63 patients with at least ten years' follow-up with three bearing types (1900 resin machined, 1050 resin machined, and 1050 resin moulded) were recruited. Patients underwent full weight-bearing model-based radiostereometric analysis to determine the bearing thickness. The linear wear rate was estimated from the change in thickness divided by the duration of implantation. RESULTS: The wear rate for 1900 resin machined (n = 19), 1050 machined (n = 21), and 1050 moulded bearings (n = 23) were 60 µm/year (sd 42), 76 µm/year (sd 32), and 57 µm/year (sd 30), respectively. There was no significant difference between 1900 machined and 1050 machined (p = 0.20), but 1050 moulded had significantly less wear than the 1050 machined (p = 0.05). Increasing femoral (p < 0.001) and tibial (p < 0.001) component size were associated with increasing wear. CONCLUSION: Wear rate is similar with 1050 and 1900 resin, but lower with moulded bearings than machined bearings. The currently used Phase 3 bearings wear rate is low (1050 moulded, 57 µm/year), but higher than the previously reported Phase 2 bearings (1900 moulded, 20 µm/year). This is unlikely to be due to the change in polyethylene but may relate to the minimally invasive approach used with the Phase 3. This approach, as well as improving function and thus increasing activity levels, may increase the risk of surgical errors, such as impingement or bearing overhang, which can increase wear. Surgeons should aim to use 4 mm thick bearings rather than 3 mm thick bearings in young patients, unless they are small and need conservative bone resections.Cite this article: Bone Joint Res 2019;8:535-543.

Response to review article published titled 'Total ankle arthroplasty versus ankle arthrodesis - a comparison of outcomes over the last decade'.

We write in response to Lawton et al.'s (J Orthop Surg Res 12:76, 2017) important systematic review comparing the outcomes of total ankle replacement (TAR) and ankle arthrodesis (AA) after reviewing the existing literature. Traditionally, AA was the gold standard treatment for ankle osteoarthritis but there is renewed interest in TAR given modern design advantages of preserved ankle motion and gait. We outline some pertinent issues for surgeons to consider when interpreting results from review articles comparing treatment types given the limitations of primary studies. These include significant clinical heterogeneity from the indication for surgery, different treatment type subgroups and from poorly defined clinical outcomes.

Posterior Bearing Overhang Following Medial and Lateral Mobile Bearing Unicompartmental Knee Replacements.

This study explores the extent of bearing overhang following mobile bearing Oxford unicompartmental knee replacement (OUKR) (Oxford Phase 3, Zimmer Biomet). The Oxford components are designed to be fully congruent, however knee movements involve femoral rollback, which may result in bearing overhang at the posterior margin of the tibial implant, with potential implications for; pain, wear, and dislocation. Movement is known to be greater, and therefore posterior overhang more likely to occur, with; lateral compared to medial implants, anterior cruciate ligament (ACL) deficiency (ACLD) compared to ACL intact (ALCI), and at extremes of movement. Twenty-four medial, and 20 domed lateral, OUKRs underwent sagittal plane knee fluoroscopy during step-up and forward lunge exercises. The bearing position was inferred from the relative position of the femoral and tibial components. On the basis of the individual component sizes and geometry the extent the posterior part of the bearing which overhung the posterior part of the tibial component was calculated. There was no significant posterior overhang in knees with medial implants. Knees with lateral domed implants exhibited overhang at flexion angles beyond 60°, the magnitude of which increased with increasing flexion angle, reaching a maximum of 50% of the bearing length at 140° (range 0-140°). This demonstrates a clear difference between the kinematics, and prevalence and extent of posterior bearing overhang between medial and lateral OUKRs. © 2019 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 37:1938-1945, 2019.

Age and Outcomes of Medial Meniscal-Bearing Unicompartmental Knee Arthroplasty.

BACKGROUND: National joint registries report increasing revision rates with decreasing patient age for all types of joint arthroplasty. This study aimed to explore the effect of age on function and revision risk in patients undergoing medial meniscal-bearing UKA. METHODS: A prospectively followed cohort of 1000 consecutive medial meniscal-bearing UKAs at a designer center was analyzed. All knees were implanted for recommended indications and had mean 10-year follow-up. Patients were grouped by age at surgery (<55, 55 to <65, 65 to <75, 75+). Oxford Knee Scores (OKS) were assessed at 5 and 10 years. Component-time revision incidence rates and Kaplan-Meier implant survival were calculated. RESULTS: Mean patient age at surgery was 66.6 years (range, 33-88). All age-groups had significant (P < .001) improvement in OKS over time, and at 5 years achieved a median OKS of 44. At 10 years, median OKS, from youngest group to eldest, were 44, 45, 42, and 39, with the eldest group having a significantly lower OKS (P < .01). Ten-year implant survival rates were 97%, 94%, 94%, and 93%, respectively, and was not significantly associated with age at UKA. CONCLUSION: Medial meniscal-bearing UKA provides good functional outcomes in all age-groups; however, in older patients (75+), the functional outcome deteriorated at 10 years presumably due to deteriorating health. Contrary to registry observations, the revision rate was not higher in younger patients. These results suggest that, with correct indications, patient age should not be considered a contraindication to medial meniscal-bearing UKA.