Portable and Autonomous PEDOT-Modified Flexible Paper-Based Methanol Fuel Cell Sensing Platform Applied to L1CAM Recombinant Protein Detection.

This work describes first a 5-stack direct methanol fuel cell (DMFC) based on poly(3,4-ethylenedioxythiophene)-modified paper (PEDOT/PB-DMFC), which acts as an energy source and biosensor, coupled to an electrochromic cell (EC). It is autonomous and monitors the biosensor response by color change, as appropriate for point-of-care (POC) applications. In detail, DMFC strips were developed from square Whatman paper, and the EC was made on baking paper treated with polydimethylsiloxane (PDMS). The PEDOT/PB-DMFCs operate in a passive mode with a few microliters of diluted methanol. The biosensor layer was obtained on the anode ink (a composite of EDOT, oxidized multiwalled carbon nanotubes, and carbon black with platinum and ruthenium) by electropolymerizing 3,4-ethylenedioxythiophene (EDOT), in situ, in the presence of L1CAM. Each PEDOT/PB-DMFC single cell generates a voltage in the range of 0.3-0.35 V depending on the cell, and a five-cell stack delivers a 1.5-1.6 V voltage range when fed with 0.5 M methanol. The fabricated PEDOT/PB-DMFC/biosensor was calibrated against L1CAM, showing linear responses from 1.0 × 10-12 to 1.0 × 10-8 M with a detection limit of 1.17 × 10-13 M (single cell mode). When the EC was connected to the PEDOT/PB-DMFC device, a color gradient was observed. Overall, this work opens horizons to the use of biosensors even in places with energy scarcity and offers an alternative to reducing the current energy demand.

New autonomous and self-signaling biosensing device for sarcosine detection.

An early diagnosis is the gold standard for cancer survival. Biosensors have proven their effectiveness in monitoring cancer biomarkers but are still limited to a series of requirements. This work proposes an integrated power solution, with an autonomous and self-signaling biosensing device. The biorecognition element is produced in situ by molecular imprinting to detect sarcosine, a known biomarker for prostate cancer. The biosensor was assembled on the counter-electrode of a dye-sensitized solar cell (DSSC), simultaneously using EDOT and Pyrrole as monomers for the biomimetic process and the catalytic reduction of triiodide in the DSSC. After the rebinding assays, the hybrid DSSC/biosensor displayed a linear behavior when plotting the power conversion efficiency (PCE) and the charge transfer resistance (RCT) against the logarithm of the concentration of sarcosine. The latter obtained a sensitivity of 0.468 Ω/decade of sarcosine concentration, with a linear range between 1 ng/mL and 10 µg/mL, and a limit of detection of 0.32 ng/mL. When interfacing an electrochromic cell, consisting of a PEDOT-based material, with the hybrid device, a color gradient between 1 ng/mL and 10 µg/mL of sarcosine was observed. Thus, the device can be used anywhere with access to a light source, completely equipment-free, suitable for point-of-care analysis and capable of detecting sarcosine within a range of clinical interest.

Sustainability and economic evaluation of microalgae grown in brewery wastewater.

This article evaluates the sustainability and economic potential of microalgae grown in brewery wastewater for biodiesel and biomass production. Three sustainability and two economic indicators were considered in the evaluation within a life cycle perspective. For the production system the most efficient process units were selected. Results show that harvesting and oil separation are the main process bottlenecks. Microalgae with higher lipid content and productivity are desirable for biodiesel production, although comparable to other biofuel's feedstock concerning sustainability. However, improvements are still needed to reach the performance level of fossil diesel. Profitability reaches a limit for larger cultivation areas, being higher when extracted biomass is sold together with microalgae oil, in which case the influence of lipid content and areal productivity is smaller. The values of oil and/or biomass prices calculated to ensure that the process is economically sound are still very high compared with other fuel options, especially biodiesel.

Biocompatibility of poly(lactic acid) with incorporated graphene-based materials.

The incorporation of graphene-based materials has been shown to improve mechanical properties of poly(lactic acid) (PLA). In this work, PLA films and composite PLA films incorporating two graphene-based materials - graphene oxide (GO) and graphene nanoplatelets (GNP) - were prepared and characterized regarding not only biocompatibility, but also surface topography, chemistry and wettability. The presence of both fillers changed the films surface topography, increasing the roughness, and modified the wettability - the polar component of surface free energy increased 59% with GO and decreased 56% with GNP. Mouse embryo fibroblasts incubated with both fillers exceeded the IC(50) in both cases with a concentration of 10 µg mL(-1). No variations in cell proliferation at the surface of the composite films were observed, except for those containing GO after 24 h incubation, which presented higher cell proliferation than pristine PLA films. Platelet adhesion to PLA and PLA/GNP films was lower in the presence of plasma proteins than when no proteins were present. Furthermore, incorporation of GNP into PLA reduced platelet activation in the presence of plasma proteins. The results indicated that low concentrations of GO and GNP may be incorporated safely in PLA to improve aspects relevant for biomedical applications, such as mechanical properties.

Removal of industrial cutting oil from oil emulsions by polymeric ultra- and microfiltration membranes.

The utilization of micro- and ultrafiltration with polymeric membranes for treatment of industrial cutting oil emulsion was investigated. The performance of 14 different membranes with pore sizes in the range of 1-800 nm, representing 8 different materials and varying hydrophobicity, was determined experimentally. Membrane permeances between 1.6 and 939 L m 2 h(-1) bar(-1) have been observed for the different samples as well as oil rejections between 3.42% and 99.99%. Membrane pore size and contact angle showed little influence on both values, while an interesting correlation is displayed to the individual membranes' capillary pressures. A possible explanation for this phenomenon is suggested based on the formation of oil films on the membrane surface. From the investigated membranes, the best-suited one for cutting oil treatment was selected and subjected to further experiments. The effect of process temperatures between 22 and 43 degrees C and of feed oil concentrations between 0 and 20 vol % on the removal performance was determined. The results correspond to the explanation suggested previously.