Risk assessment and molecular mechanism of Sclerotium rolfsii resistance to boscalid.

Boscalid, a widely used SDHI fungicide, has been employed in plant disease control for over two decades. However, there is currently no available information regarding its antifungal activity against Sclerotium rolfsii and the potential risk of resistance development in this pathogen. In this study, we evaluated the sensitivity of 100 S. rolfsii strains collected from five different regions in China during 2018-2019 to boscalid using mycelial growth inhibition method and assessed the risk of resistance development. The EC50 values for boscalid ranged from 0.2994 µg/mL to 1.0766 µg/mL against the tested strains, with an average EC50 value of 0.7052 ± 0.1473 µg/mL. Notably, a single peak sensitivity baseline was curved, indicating the absence of any detected resistant strains. Furtherly, 10 randomly selected strains of S. rolfsii were subjected to chemical taming to evaluate its resistance risk to boscalid, resulting in the successful generation of six stable and inheritable resistant mutants. These mutants exhibited significantly reduced mycelial growth, sclerotia production, and virulence compared to their respective parental strains. Cross-resistance tests revealed a correlation between boscalid and flutolanil, benzovindiflupyr, pydiflumetofen, fluindapyr, and thifluzamide; however, no cross-resistance was observed between boscalid and azoxystrobin. Thus, we conclude that the development risk of resistance in S. rolfsii to boscalid is low. Boscalid can be used as an alternative fungicide for controlling peanut sclerotium blight when combined with other fungicides that have different mechanisms of action. Finally, the target genes SDHB, SDHC, and SDHD in S. rolfsii were initially identified, cloned and sequenced to elucidate the mechanism of S. rolfsii resistance to boscalid. Two mutation genotypes were found in the mutants: SDHD-D111H and SDHD-H121Y. The mutants carrying SDHD-H121Y exhibited moderate resistance, while the mutants with SDHD-D111H showed low resistance. These findings contribute to our comprehensive understanding of molecular mechanisms underlying plant pathogens resistance to SDHI fungicides.

The discovery of three-dimensional Van Hove singularity.

Arising from the extreme/saddle point in electronic bands, Van Hove singularity (VHS) manifests divergent density of states (DOS) and induces various new states of matter such as unconventional superconductivity. VHS is believed to exist in one and two dimensions, but rarely found in three dimension (3D). Here, we report the discovery of 3D VHS in a topological magnet EuCd2As2 by magneto-infrared spectroscopy. External magnetic fields effectively control the exchange interaction in EuCd2As2, and shift 3D Weyl bands continuously, leading to the modification of Fermi velocity and energy dispersion. Above the critical field, the 3D VHS forms and is evidenced by the abrupt emergence of inter-band transitions, which can be quantitatively described by the minimal model of Weyl semimetals. Three additional optical transitions are further predicted theoretically and verified in magneto-near-infrared spectra. Our results pave the way to exploring VHS in 3D systems and uncovering the coordination between electronic correlation and the topological phase.

Multiple independent origins of duplicated mitochondrial control regions indicate an apomorphy in the Thysanoptera (Insecta).

The mitochondrial genome (mitogenome) of thrips is characterized by the presence of control region (CR) duplication. However, the evolution pattern of duplicated CRs in thrips is still unclear. In this study, the multiple independent origins of duplicated CR indicated that the CR duplication was not an ancestral state for Thysanoptera. The macroevolutionary pattern suggested that the earliest CR duplication event occurred in the middle Cretaceous (94.85 Ma) coincided with rearrangement events forming the ancestors of Aeolothripidae, but much later than that forming the ancestors of the suborder Terebrantia. The mitogenome with duplicated CRs showed a higher rate of gene rearrangement. The sequence similarity of the CR copies and divergence time were negatively correlated, indicating age-related deterioration of mitochondrial function. No significant differences were found in the mitochondrial DNA, the P123 and P4FD between the single and multiple-CR charactered mitogenomes, which suggested that the duplicated CRs may not affect the replication process in thrip mitogenome. The mitogenomes with duplicated CRs (mean: 0.0088 subs/s/my) show a significantly increased evolutionary rate than that with a single one (mean: 0.0058 subs/s/my). However, it seems that this higher evolutionary rate did not have adaptive mechanisms in Terebrantia. We speculated that the duplicated CRs may cause a more intense production of energy by mitochondria, and an accelerated mutation and substitution rate is expected in such mitogenomes. Our study provided new insights into the presence of CR duplications and their evolution in the mitogenomes of thrips.

Research on the Adsorption Law of HFAD Agents on the Surface of Porous Media during Hydraulic Fracturing-Assisted Oil Displacement in Low-Permeability Reservoirs.

Adsorption loss of surfactants in porous media is one of the key factors affecting their application in low-permeability reservoirs. The hydraulic fracturing-assisted oil displacement (HFAD) technology can effectively reduce the adsorption loss of surfactants in porous media. However, the adsorption laws of HFAD agents (surfactants) during the HFAD process are still unclear. It was studied based on physical simulation experiments in this paper. The results showed that 0.3% SY-D as the HAFD agent achieved the best effect, which could reduce the oil-water interfacial tension to 0.0239 mN/m and increase the wettability index to 0.7492. In the high-pressure injection process of HFAD technology, the injection pressure and core permeability are positively correlated with the dynamic saturation adsorption capacity of the HFAD agent on the surface of porous media and the ambient temperature is negatively correlated with it. The higher the injection pressure and the larger the core permeability, the lower the dynamic saturation adsorption capacity of the HFAD agent on the porous media surface. In addition, since adsorption is an exothermic process, increasing the temperature has an inhibitory effect on adsorption. The higher the temperature, the slower the adsorption process of the HFAD agent on porous media. Among the three influencing factors, permeability has the greatest influence on the dynamic saturation adsorption capacity of the HFAD agent on the surface of core porous media, followed by injection pressure, and temperature has the least influence on it. Therefore, when implementing HFAD technology for the reservoir with low permeability, it can be considered to increase the injection pressure of HFAD technology to reduce the dynamic saturation adsorption capacity so as to increase the effective concentration of the agent. The research results have certain guiding significance for the application of HFAD technology in the field.

Mechanism of Low Chemical Agent Adsorption by High Pressure for Hydraulic Fracturing-Assisted Oil Displacement Technology: A Study of Molecular Dynamics Combined with Laboratory Experiments.

This study investigates the influence of physical parameters such as porosity, permeability, pore-throat radius, and specific surface area/volume on the adsorption capacity of surfactants in the pore surface of reservoirs. In the meantime, the hydraulic fracturing-assisted oil displacement (HFAD) technique can effectively improve the permeability and porosity of pores in the reservoir, which may affect the adsorption capacity of surfactants in low-permeability reservoirs. This may help to reduce the adsorption loss of surfactants in low-permeability reservoirs. Based on physical simulation methods, dynamic adsorption experiments were conducted to clarify the dynamic saturation adsorption capacity effect of high-pressure and low-pressure displacement agents by the HFAD technique. In addition, the molecular dynamics simulation method was used to study the effect of high-pressure conditions of HFAD on the adsorption capacity of surfactants on weakly lipophilic silica walls. Under the condition of high injection pressure by the HFAD technique, the fluid flow velocity and the initial kinetic energy of molecules increase, while the absolute value of the electrostatic potential energy in the system decreases. In addition, the van der Waals potential energy increases. In other words, the smaller the gravitational attraction experienced by the surfactant molecules during adsorption, the greater the repulsive force. Under the dual action of electrostatic force and van der Waals forces, the absolute values of the adsorption energy and the free energy decrease. The adsorption capacity of the surfactant molecules is weakened. Moreover, the decrease in adsorption capacity has little effect on the improvement of wettability, indicating that the adsorption of the surfactant reduced by HFAD technology is mostly ineffective adsorption.

Giant Superlinear Power Dependence of Photocurrent Based on Layered Ta2 NiS5 Photodetector.

Photodetector based on two-dimensional (2D) materials is an ongoing quest in optoelectronics. 2D photodetectors are generally efficient at low illuminating power but suffer severe recombination processes at high power, which results in the sublinear power-dependent photoresponse and lower optoelectronic efficiency. The desirable superlinear photocurrent is mostly achieved by sophisticated 2D heterostructures or device arrays, while 2D materials rarely show intrinsic superlinear photoresponse. This work reports the giant superlinear power dependence of photocurrent based on multilayer Ta2 NiS5 . While the fabricated photodetector exhibits good sensitivity (3.1 mS W-1 per □) and fast photoresponse (31 µs), the bias-, polarization-, and spatial-resolved measurements point to an intrinsic photoconductive mechanism. By increasing the incident power density from 1.5 to 200 µW µm-2 , the photocurrent power dependence varies from sublinear to superlinear. At higher illuminating conditions, prominent superlinearity is observed with a giant power exponent of γ = 1.5. The unusual photoresponse can be explained by a two-recombination-center model where density of states of the recombination centers (RC) effectively closes all recombination channels. The photodetector is integrated into camera for taking photos with enhanced contrast due to superlinearity. This work provides an effective route to enable higher optoelectronic efficiency at extreme conditions.

Topological Lifshitz transition and one-dimensional Weyl mode in HfTe5.

Landau band crossings typically stem from the intra-band evolution of electronic states in magnetic fields and enhance the interaction effect in their vicinity. Here in the extreme quantum limit of topological insulator HfTe5, we report the observation of a topological Lifshitz transition from inter-band Landau level crossings using magneto-infrared spectroscopy. By tracking the Landau level transitions, we demonstrate that band inversion drives the zeroth Landau bands to cross with each other after 4.5 T and forms a one-dimensional Weyl mode with the fundamental gap persistently closed. The unusual reduction of the zeroth Landau level transition activity suggests a topological Lifshitz transition at 21 T, which shifts the Weyl mode close to the Fermi level. As a result, a broad and asymmetric absorption feature emerges due to the Pauli blocking effect in one dimension, along with a distinctive negative magneto-resistivity. Our results provide a strategy for realizing one-dimensional Weyl quasiparticles in bulk crystals.

The Precipitation Behavior of a Cu-Ni-Si Alloy with Cr Addition Prepared by Heating-Cooling Combined Mold (HCCM) Continuous Casting.

A Cu-Ni-Si alloy containing (Ni + Si) ≥ 5 wt.%, with the addition of Cr, is fabricated by HCCM continuous casting and two steps of aging treatment. The evolution of the microstructures and precipitations, as well as the effect of Cr atoms, is studied in this paper. An excellent combination of mechanical property (hardness HV 250-270) and electrical conductivity (46-47 %IACS) is obtained by the first step aging at 500 °C for 0.25 h and the second step aging at 450 °C for 1 h. The cold rolling and aging process are directly conducted on the solution treated specimens fabricated by HCCM continuous casting process without hot deformation, since the excellent homogeneity of matrix is obtained by solution treatment with δ-Ni2Si precipitates dissolved. It is found that the formation of discontinuous precipitation is suppressed by the formation of Cr3Si cores of 5-10 nm before the formation δ-Ni2Si. Then, the nucleation and growth of δ-Ni2Si precipitates occurs around the boundaries of these Cr3Si cores, leading to an enhanced nucleation rate. This study provides a promising direction for the design and optimization of Cu-Ni-Si alloys based on the further understanding of the effect of the addition of Cr.

Comparative Raman spectroscopy of magnetic topological material EuCd2X2(X=P, As).

EuCd2X2(X = P, As) is a new class of magnetic topological materials discovered recently. The electronic structure and the band topology are intimately coupled with its magnetism, giving rise to interesting properties such as spin fluctuation and colossal magnetoresistance. Phonon excitation can contribute to the quasi-particle response of the topological matters through spin-lattice and electron-phonon coupling. However, the phonon properties of this material family remain unexplored. Here we report a comparative study of Raman-active vibration modes in EuCd2X2(X = P, As) by means of angle-resolved, temperature-resolved, and magnetic-field-resolved Raman spectroscopy together with the first-principle calculations and Raman tensor analysis. The phonon properties can be tuned by chemical potential and temperature within the material family. All the phonon modes are softened with increased chemical pressure by replacing P with As. Angle-resolved polarized Raman spectroscopy reveals the configuration-sensitive Raman activity and the isotropic intensity response. In addition, the magneto-Raman spectrum indicates the stability of Raman-active vibration modes against the magnetic field at room temperature. Our work sheds light on the phonon dynamics of magnetic topological matters, which are potentially coupled with the topological charge and spin excitation.

The Limitations in Current Studies of Organic Fouling and Future Prospects.

Microfiltration and ultrafiltration for water/wastewater treatment have gained global attention due to their high separation efficiency, while membrane fouling still remains one of their bottlenecks. In such a situation, many researchers attempt to obtain a deep understanding of fouling mechanisms and to develop effective fouling controls. Therefore, this article intends to trigger discussions on the appropriate choice of foulant surrogates and the application of mathematic models to analyze fouling mechanisms in these filtration processes. It has been found that the commonly used foulant surrogate (sodium alginate) cannot ideally represent the organic foulants in practical feed water to explore the fouling mechanisms. More surrogate foulants or extracellular polymeric substance (EPS) extracted from practical source water may be more suitable for use in the studies of membrane fouling problems. On the other hand, the support vector machine (SVM) which focuses on the general trends of filtration data may work as a more powerful simulation tool than traditional empirical models to predict complex filtration behaviors. Careful selection of foulant surrogate substances and the application of accurate mathematical modeling for fouling mechanisms would provide deep insights into the fouling problems.

Novel Surrogates for Membrane Fouling and the Application of Support Vector Machine in Analyzing Fouling Mechanism.

It is difficult to recognize specific fouling mechanisms due to the complexity of practical feed water, thus the current studies usually employ foulant surrogates to carry out research, such as alginate and xanthan gum. However, the representativeness of these surrogates is questionable. In this work, the classical surrogates (i.e., alginate and xanthan gum) were systematically studied, and results showed that they behaved differently during filtration. For the mixture of alginate and xanthan gum, both filtration behaviors and adsorption tests performed by quartz-crystal microbalance with dissipation monitoring (QCM-D) indicated that alginate plays a leading role in fouling development. Furthermore, by examining the filtration behaviors of extracellular polymeric substances (EPS) extracted from practical source water, it turns out that the gel layer formation is responsible for EPS fouling, and the properties of gel layer formed by EPS share more similarities with that formed from pectin instead of alginate. In addition, with the use of experimental data sets extracted from this study and our previous studies, a modeling method was established and tested by the support vector machine (SVM) to predict complex filtration behaviors. Results showed that the small differences of fouling mechanisms lying between alginate and pectin cannot be recognized by Hermia's models, and SVM can show a discrimination as high as 76.92%. As such, SVM may be a powerful tool to predict complex filtration behaviors.

Remote Sensing Image Dataset Expansion Based on Generative Adversarial Networks with Modified Shuffle Attention.

With the development of science and technology, neural networks, as an effective tool in image processing, play an important role in gradual remote-sensing image-processing. However, the training of neural networks requires a large sample database. Therefore, expanding datasets with limited samples has gradually become a research hotspot. The emergence of the generative adversarial network (GAN) provides new ideas for data expansion. Traditional GANs either require a large number of input data, or lack detail in the pictures generated. In this paper, we modify a shuffle attention network and introduce it into GAN to generate higher quality pictures with limited inputs. In addition, we improved the existing resize method and proposed an equal stretch resize method to solve the problem of image distortion caused by different input sizes. In the experiment, we also embed the newly proposed coordinate attention (CA) module into the backbone network as a control test. Qualitative indexes and six quantitative evaluation indexes were used to evaluate the experimental results, which show that, compared with other GANs used for picture generation, the modified Shuffle Attention GAN proposed in this paper can generate more refined and high-quality diversified aircraft pictures with more detailed features of the object under limited datasets.

Highly flexible and degradable memory electronics comprised of all-biocompatible materials.

Biocompatible materials have received increasing attention as one of the most important building blocks for flexible and transient memories. Herein, a fully biocompatible resistive switching (RS) memory electronic composed of a carbon dot (CD)-polyvinyl pyrrolidone (PVP) nanocomposite and a silver nanowire (Ag NW) network buried in a flexible gelatin film is introduced with promising nonvolatile RS characteristics for flexible and transient memory applications. The fabricated device exhibited a rewritable flash-type memory behavior, such as low operation voltage (≈-1.12 V), high ON/OFF ratio (>102), long retention time (over 104 s), and small bending radius (15 mm). As a proof of degradability, this transient memory can dissolve completely within 90 s after being immersed into deionized water at 55 °C; it can decompose naturally in soil within 6 days. This fully biocompatible memory electronic paves a novel way for flexible and wearable green electronics.

A Global Overview of SARS-CoV-2 in Wastewater: Detection, Treatment, and Prevention.

A novel coronavirus (SARS-CoV-2) causing corona virus disease 2019 (COVID-19) has attracted global attention due to its highly infectious and pathogenic properties. Most of current studies focus on aerosols released from infected individuals, but the presence of SARS-CoV-2 in wastewater also should be examined. In this review, we used bibliometrics to statistically evaluate the importance of water-related issues in the context of COVID-19. The results show that the levels and transmission possibilities of SARS-CoV-2 in wastewater are the main concerns, followed by potential secondary pollution by the intensive use of disinfectants, sludge disposal, and the personal safety of workers. The presence of SARS-CoV-2 in wastewater requires more attention during the COVID-19 pandemic. Thus, the most effective techniques, i.e., wastewater-based epidemiology and quantitative microbial risk assessment, for virus surveillance in wastewater are systematically analyzed. We further explicitly review and analyze the successful operation of a sewage treatment plant in Huoshenshan Hospital in China as an example and reference for other sewage treatment systems to properly ensure discharge safety and tackle the COVID-19 pandemic. This review offers deeper insight into the prevention and control of SARS-CoV-2 and similar viruses in the post-COVID-19 era from a wastewater perspective.

The structural and functional properties of polysaccharide foulants in membrane fouling.

Polysaccharide foulant is known to play a crucial role in membrane fouling, however the detailed influential mechanisms and the pertinence to specific structure of polysaccharides, as well as intermolecular interactions among them with and without divalent cation are still indistinct. In this study, seven polysaccharides including agarose, sodium alginate, carrageenan, pectin, starch, sodium carboxymethylcellulose (CMC) and xanthan gum, with different chain and molecular structures, were used as model foulants to investigate the role of structural and functional features of polysaccharides in membrane fouling. Two Hermia's models (classical and mass-transfer models) as well as the resistance-in-series model were used to analyze the fouling mechanism. Results show that the spatial configuration of foulant molecule is significant in membrane fouling which actually controls the resistance of gel layer formed on membrane. Polysaccharides with different properties show distinct fouling mechanisms which are in accordance with the four models described by Hermia respectively. Cations may change the interaction of polysaccharide foulant which further leads to the structural change of the gel layer. It turns out that mass-transfer model is more suitable for interpreting of crossflow filtration data. So far, little has been known about the effects of molecule structure of polysaccharides on membrane fouling. In this paper, we provide a basic database for polysaccharide fouling which will work as a theoretical basis for finding more effective measures to prevent and control membrane fouling.

The role of transparent exopolymer particles (TEP) in membrane fouling: A critical review.

Transparent exopolymer particles (TEP) as gel-like particulate acidic polysaccharide have been commonly found in marine, surface water and wastewater. Currently, increasing interest has been devoted to TEP-associated membrane fouling in different membrane systems for water and wastewater treatment, thus this review attempts to provide a holistic view and critical analysis with regard to the definition, formation, detection and properties of TEP, which could ultimately determine its fouling potential. It appears that there is not a common consensus on the actual role of TEP in membrane fouling development due to the subjective definition and highly debatable detection method of TEP. It was clearly demonstrated in this review that the formation of TEP was largely related to cations in water and wastewater which indeed determined the cross-linking degree of precursor materials (e.g. polysaccharides) via intermolecular interactions, and subsequently the quantity of TEP formed. The binding between cations ions (e.g. monovalent, divalent and trivalent cations) and polysaccharide not only depends on the functional groups of polysaccharide, but also its spatial configuration. These in turn suggest that the formation, property and ultimate fouling potential of TEP would be closely related to the type and concentration of cations, while well explaining the controversial reports on TEP-associated fouling in the literature. In addition, the fouling mechanisms of TEP are also elucidated with details in this review, including (i) the formation of TEP-associated gel layer on membrane surface; (ii) carrying microorganisms to membrane surface via protobiofilm and (iii) trapping of deformable TEP in membrane pores. Consequently, it is apparent that TEP is an ignored determinant of membrane fouling, which has not yet been seriously addressed in the design and operation of membrane systems for water and wastewater treatment.

Sustainable and Transparent Fish Gelatin Films for Flexible Electroluminescent Devices.

In the past decades, various alternating current electroluminescent (ACEL) devices, especially the flexible ones, have been developed and used in flat panel display, large-scale decorating, logo display lighting, optical signaling, etc. Transparent plastics are usually used as substrates in ACEL devices; however, they are undegradable and may cause serious environmental pollution. Herein, we have developed a flexible transient ACEL device based on transparent fish gelatin (FG) films. The FG films were made from fish scales, which are sustainable, cost-efficient, and eco-friendly. These films could dissolve in water within seconds at 60 °C and degrade completely within 24 days in soil. The transmittance of these FG films was up to 91.1% in the visible spectrum, comparable to that of polyethylene terephthalate (PET) (90.4%). After forming a composite with silver nanowires (Ag NWs), the Ag NWs-FG film showed a transmittance up to 82.3% and a sheet resistance down to 22.4 Ω sq-1. The fabricated ACEL device based on the Ag NWs-FG film exhibited high flexibility and luminance up to 56.0 cd m-2. The device could be dissolved in water within 3 min. Our work demonstrates that the sustainable, flexible, and transparent FG films are a promising alternative for green and degradable substrates in the field of flexible electronics, including foldable displays, wearable devices, and health monitoring.

Watt-level widely tunable femtosecond mid-infrared KTiOAsO4 optical parametric oscillator pumped by a 1.03 µm Yb:KGW laser.

A high-power, high-repetition-rate, broadband tunable femtosecond optical parametric oscillator (OPO) is constructed based on KTiOAsO4 crystal, pumped by a 75.5 MHz mode-locked Yb:KGW laser. With 7 W pump power, the OPO generates as much as 2.32 W of signal power at 1.55 µm and 1.31 W of idler power at 3.05 µm, corresponding to a total conversion efficiency of 51.8%. Operating at 151 MHz repetition rate, the wavelength of the signal covers 1.41-1.71 µm with a tunable idler range of 2.61-3.84 µm. The idler bandwidth is more than 180 nm over the entire mid-infrared range. By compensating intracavity dispersion, the signal pulse has a nearly Fourier transform-limited duration of 129 fs at 1.52 µm.

High-power, widely tunable, green-pumped femtosecond BiB3O6 optical parametric oscillator.

We report on an efficient high-power, widely tunable femtosecond optical parametric oscillator in BiB3O6, synchronously pumped by a frequency-doubled mode-locked Yb:KGW laser at 515 nm. Using collinear type I (o→e+e) phase matching, a resonant wavelength range of 688-1057 nm at a 151-MHz repetition rate is demonstrated, with a tunable idler range of 1150-1900 nm. The output power at 705 nm is 1.09 W for 3.6 W pump power exceeding 30% conversion efficiency. Near-transform-limited pulses down to 71 fs are achieved by deploying extracavity dispersion compensation in a pair of SF6 prisms.

Expression partitioning of homeologs and tandem duplications contribute to salt tolerance in wheat (Triticum aestivum L.).

Salt stress dramatically reduces crop yield and quality, but the molecular mechanisms underlying salt tolerance remain largely unknown. To explore the wheat transcriptional response to salt stress, we performed high-throughput transcriptome sequencing of 10-day old wheat roots under normal condition and 6, 12, 24 and 48 h after salt stress (HASS) in both a salt-tolerant cultivar and salt-sensitive cultivar. The results demonstrated global gene expression reprogramming with 36,804 genes that were up- or down-regulated in wheat roots under at least one stress condition compared with the controls and revealed the specificity and complexity of the functional pathways between the two cultivars. Further analysis showed that substantial expression partitioning of homeologous wheat genes occurs when the plants are subjected to salt stress, accounting for approximately 63.9% (2,537) and 66.1% (2,624) of the homeologous genes in 'Chinese Spring' (CS) and 'Qing Mai 6' (QM). Interestingly, 143 salt-responsive genes have been duplicated and tandemly arrayed on chromosomes during wheat evolution and polyploidization events, and the expression patterns of 122 (122/143, 85.3%) tandem duplications diverged dynamically over the time-course of salinity exposure. In addition, constitutive expression or silencing of target genes in Arabidopsis and wheat further confirmed our high-confidence salt stress-responsive candidates.