Size Matters in Conjugated Polymer Chirality-Selective SWCNT Extraction.

Carbon-based nanomaterials have catalyzed breakthroughs across various scientific and engineering disciplines. The key to unlocking a new generation of tailor-made nanomaterials based on single-walled carbon nanotubes (SWCNTs) lies in the precise sorting of raw material into individual chiralities, each possessing unique properties. This can be achieved using conjugated polymer extraction (CPE), but to a very limited extent since the process generates only a few chirality-enriched suspensions. Therefore, it is imperative to comprehend the mechanism of the wrapping of SWCNTs by polymers to unleash CPE's full potential. However, the lack of a diverse palette of chirality-selective polymers with varying macromolecular parameters has hindered a comprehensive understanding of how the nature of the polymer affects the performance and selectivity of SWCNT isolation. To address this gap, multiple batches of such polymers are synthesized to elucidate the impact of molecular weight and dispersity on the purity and concentrations of the generated SWCNT suspensions. The obtained results explain the inconsistent outcomes reported in the literature, greatly improving the application potential of this promising SWCNT sorting approach. Concomitantly, the discovered significant influence of the macromolecular characteristics of conjugated polymers on the SWCNT isolation efficacy sheds considerable insight into the unresolved mechanism of this sorting technique.

Ionic Liquid-Based Polymer Matrices for Single and Dual Drug Delivery: Impact of Structural Topology on Characteristics and In Vitro Delivery Efficiency.

Previously reported amphiphilic linear and graft copolymers, derived from the ionic liquid [2-(methacryloyloxy)ethyl]trimethylammonium chloride (TMAMA_Cl‾), along with their conjugates obtained through modification either before or after polymerization with p-aminosalicylate anions (TMAMA_PAS‾), were employed as matrices in drug delivery systems (DDSs). Based on the counterion type in TMAMA units, they were categorized into single drug systems, manifesting as ionic polymers with chloride counterions and loaded isoniazid (ISO), and dual drug systems, featuring ISO loaded in self-assembled PAS conjugates. The amphiphilic nature of these copolymers was substantiated through the determination of the critical micelle concentration (CMC), revealing an increase in values post-ion exchange (from 0.011-0.063 mg/mL to 0.027-0.181 mg/mL). The self-assembling properties were favorable for ISO encapsulation, with drug loading content (DLC) ranging between 15 and 85% in both single and dual systems. In vitro studies indicated ISO release percentages between 16 and 61% and PAS release percentages between 20 and 98%. Basic cytotoxicity assessments using the 2,5-diphenyl-2H-tetrazolium bromide (MTT) test affirmed the non-toxicity of the studied systems toward human non-tumorigenic lung epithelial cell line (BEAS-2B) cell lines, particularly in the case of dual systems bearing both ISO and PAS simultaneously. These results confirmed the effectiveness of polymeric carriers in drug delivery, demonstrating their potential for co-delivery in combination therapy.

PdNPs/NiNWs as a welding tool for the synthesis of polyfluorene derivatives by Suzuki polycondensation under microwave radiation.

Conjugated polymers are promising tools to differentiate various types of semiconducting single-walled carbon nanotubes (s-SWCNTs). However, their synthesis is challenging. Insufficient control over molecular weights, and unpredictive/unrepeatable batches hinder possible applications and scale-up. Furthermore, commercial homogeneous catalysts often require inert conditions and are almost impossible to recycle. To overcome these problems, we present a nanocatalyst consisting of magnetic nickel nanowires decorated with highly active palladium nanoparticles. A two-step wet chemical reduction protocol with the assistance of sonochemistry was employed to obtain a heterogeneous catalyst capable of conducting step-growth Suzuki polycondensation of a fluorene-based monomer. Additionally, we enhanced the performance of our catalytic system via controlled microwave irradiation, which significantly shortened the reaction time from 3 d to only 1 h. We studied the influence of the main process parameters on the yield and polymer chain length to gain insight into phenomena occurring in the presence of metallic species under microwave irradiation. Finally, the produced polymers were used to extract specific s-SWCNTs by conjugated polymer extraction to validate their utility.

Traditional vs. Energetic and Perchlorate vs. "Green": A Comparative Study of the Choice of Binders and Oxidising Agents.

The aim of this article is to compare rocket propellants containing a traditional binder (hydroxyl-terminated polybutadiene) and an energetic binder (glycidyl azide polymer), as well as a perchlorate oxidising agent and a "green" one, i.e., ammonium perchlorate and phase-stabilised ammonium nitrate. We have outlined the effects of individual substances on the sensitivity parameters and decomposition temperature of the produced solid propellants. The linear combustion velocity was determined using electrical methods. Heats of combustion for the propellant samples and the thermal decomposition features of the utilised binders were investigated via differential scanning calorimetry (DSC). Activation energy values for the energetic decomposition of the propellants were determined via the Kissinger method, based on DSC measurements at varied heating rates.

Mixed-Solvent Engineering as a Way around the Trade-Off between Yield and Purity of (7,3) Single-Walled Carbon Nanotubes Obtained Using Conjugated Polymer Extraction.

The inability to purify nanomaterials such as single-walled carbon nanotubes (SWCNTs) to the desired extent hampers the progress in nanoscience. Various SWCNT types can be purified by extraction, but it is challenging to establish conditions giving rise to the isolation of high-purity fractions. The problem stems from the fact that common organic solvents or water cannot provide an optimal environment for purification. Consequently, one must often decide between the separation yield and purity of the product. This article reports how through the self-synthesis of poly(9,9-dioctylfluorene-alt-benzothiadiazole) with tailored characteristics, in-depth elucidation of the extraction process, and mixed-solvent engineering, a high-yield isolation of monochiral (7,3) SWCNTs is developed. The combination of toluene and tetralin affords a separation medium of unique properties, wherein both high yield and exceptional purity can be attained simultaneously. The reported results pave the way for further research on this rare chirality, which, as illustrated herein, is much more reactive than any of the previously separated SWCNTs.

Eco-Conscious Approach to Thermoresponsive Star-Comb and Mikto-Arm Polymers via Enzymatically Assisted Atom Transfer Radical Polymerization Followed by Ring-Opening Polymerization.

This study explores the synthesis, characterization, and application of a heterofunctional initiator derived from 2-hydroxypropyl cyclodextrin (HP-ß-CD), having eight bromoester groups and thirteen hydroxyl groups allowing the synthesis of mikto-arm star-shaped polymers. The bromoesterification of HP-ß-CD was achieved using α-bromoisobutyryl bromide as the acylation reagent, modifying the cyclodextrin (CD) molecule as confirmed by electrospray ionization mass spectrometry (ESI-MS), nuclear magnetic resonance (NMR), attenuated total reflection-Fourier transform infrared (ATR-FTIR) spectroscopy analysis, and differential scanning calorimetry (DSC) thermograms. The initiator's effectiveness was further demonstrated by obtaining star-comb and mikto-arm polymers via an enzymatically assisted atom transfer radical polymerization (ATRP) method and subsequent ring-opening polymerization (ROP). The ATR polymerization quality and control depended on the type of monomer and was optimized by the way of introducing the initiator into the reaction mixture. In the case of ATRP, high conversion rates for poly(ethylene oxide) methyl ether methacrylate (OEOMA), with molecular weights (Mn) of 500 g/mol and 300 g/mol, were achieved. The molecular weight distribution of the obtained polymers remained in the range of 1.23-1.75. The obtained star-comb polymers were characterized by different arm lengths. Unreacted hydroxyl groups in the core of exemplary star-comb polymers were utilized in the ROP of ε-caprolactone (CL) to obtain a hydrophilic mikto-arm polymer. Cloud point temperature (TCP) values of the synthesized polymers increased with arm length, indicating the polymers' reduced hydrophobicity and enhanced solvation by water. Atomic force microscopy (AFM) analysis revealed the ability of the star-comb polymers to create fractals. The study elucidates advancements in the synthesis and utilization of hydrophilic sugar-based initiators for enzymatically assisted ATRP in an aqueous solution for obtaining complex star-comb polymers in a controlled manner.

Stimuli-Responsive Star Polymer as an Admixture for Crystallization of Hollow Crystals.

Polymers are becoming a very popular tool in the crystallization of different compounds. In this work, a new method of crystallization is proposed using stimuli-responsive star polymer in order to obtain hollow structure crystals. In these experiments, amphiphilic copolymer of acrylic acid (AA) and methyl acrylate (MA) were used for isohydric crystallization via they cooling of KCl in deionized water solution. The experiments were realized in quartz cuvette with a magnetic stirrer using a specialized spectrometer with precise temperature control. The crystallization course was monitored by the absorbance readings and analysis of the nucleation energetic effect. It was proved that the moment of the polymer's phase transition occurrence had an important role in the crystal growth process. On the other hand, the occurrence of phase transition did not trigger the nucleation. The supercoolings achieved in the presence of the polymer were significantly higher compared to pure salt crystallization. On the basis of analysis of Particle Size Distribution (PSD) and Critical Aggregation Concentration (CAC) of the polymer, it was proposed that the hydrophobic particles of macromolecules created from polymeric aggregates served as templates for the formation of hollow crystals. Their purity was verified using thermogravimetric analysis (TGA), 1H NMR, and XRD. Only trace amounts of polymer were found in the crystalline product.

Recovery of the N,N-Dibutylimidazolium Chloride Ionic Liquid from Aqueous Solutions by Electrodialysis Method.

Ionic liquids (ILs), named also as liquid salts, are compounds that have unique properties and molecular architecture. ILs are used in various industries; however, due to their toxicity, the ILs' recovery from the postreaction solutions is also a very important issue. In this paper, the possibility of 1,3-dialkylimidazolium IL, especially the N,N-dibutylimidazolium chloride ([C4C4IM]Cl) recovery by using the electrodialysis (ED) method was investigated. The influence of [C4C4IM]Cl concentration in diluate solution on the ED efficiency was determined. Moreover, the influence of IL on the ion-exchange membranes' morphology was examined. The recovery of [C4C4IM]Cl, the [C4C4IM]Cl flux across membranes, the [C4C4IM]Cl concentration degree, the energy consumption, and the current efficiency were determined. The results showed that the ED allows for the [C4C4IM]Cl recovery and concentration from dilute solutions. It was found that the [C4C4IM]Cl content in the concentrates after ED was above three times higher than in the initial diluate solutions. It was noted that the ED of solutions containing 5-20 g/L [C4C4IM]Cl allows for ILs recovery in the range of 73.77-92.45% with current efficiency from 68.66% to 92.99%. The [C4C4IM]Cl recovery depended upon the initial [C4C4IM]Cl concentration in the working solution. The highest [C4C4IM]Cl recovery (92.45%) and ED efficiency (92.99%) were obtained when the [C4C4IM]Cl content in the diluate solution was equal 20 g/L. Presented results proved that ED can be an interesting and effective method for the [C4C4IM]Cl recovery from the dilute aqueous solutions.

Upper Critical Solution Temperature Polymer Phase Transition as a Tool for the Control of Inorganic Salt Crystallization Process.

In this paper, the experimental research concerning the impact of the hydrophilic-hydrophobic transition of a polymer exhibiting the Upper Critical Solution Temperature (UCST) onto the crystallization process of inorganic salt is presented. A hypothesis was postulated that under favorable process conditions the sudden change of macromolecules properties and the resulting appearance of insoluble particles will induce the nucleation process of the salt. Since the transition point parameters may be precisely designed, the described mechanism would eliminate the stochastic nature of the crystallization process. Although performed experiments proved that the postulated process mechanism was incorrect, the presence of macromolecules had a significant impact on the crystallization course. The stochastic nature of the process was not eliminated; nevertheless, it seems that a specific point of nucleation was created which was independent of the cloud point temperature (TCP) of the polymer. Moreover, the surface morphology of crystals was changed.

Application of Polymers as a Tool in Crystallization-A Review.

The application of polymers as a tool in the crystallization process is gaining more and more interest among the scientific community. According to Web of Science statistics the number of papers dealing with "Polymer induced crystallization" increased from 2 in 1990 to 436 in 2020, and for "Polymer controlled crystallization"-from 4 in 1990 to 344 in 2020. This is clear evidence that both topics are vivid, attractive and intensively investigated nowadays. Efficient control of crystallization and crystal properties still represents a bottleneck in the manufacturing of crystalline materials ranging from pigments, antiscalants, nanoporous materials and pharmaceuticals to semiconductor particles. However, a rapid development in precise and reliable measuring methods and techniques would enable one to better describe phenomena involved, to formulate theoretical models, and probably most importantly, to develop practical indications for how to appropriately lead many important processes in the industry. It is clearly visible at the first glance through a number of representative papers in the area, that many of them are preoccupied with the testing and production of pharmaceuticals, while the rest are addressed to new crystalline materials, renewable energy, water and wastewater technology and other branches of industry where the crystallization process takes place. In this work, authors gathered and briefly discuss over 100 papers, published in leading scientific periodicals, devoted to the influence of polymers on crystallizing solutions.

The Influence of Polymer Composition on the Hydrolytic and Enzymatic Degradation of Polyesters and Their Block Copolymers with PDMAEMA.

Well-defined, semi-degradable polyester/polymethacrylate block copolymers, based on ε-caprolactone (CL), d,l-lactide (DLLA), glycolide (GA) and N,N'-dimethylaminoethyl methacrylate (DMAEMA), were synthesized by ring-opening polymerization (ROP) and atom transfer radical polymerization. Comprehensive degradation studies of poly(ε-caprolactone)-block-poly(N,N'-dimethylaminoethyl methacrylate) (PCL-b-PDMAEMA) on hydrolytic degradation and enzymatic degradation were performed, and those results were compared with the corresponding aliphatic polyester (PCL). The solution pH did not affect the hydrolytic degradation rate of PCL (a 3% Mn loss after six weeks). The presence of a PDMAEMA component in the copolymer chain increased the hydrolysis rates and depended on the solution pH, as PCL-b-PDMAEMA degraded faster in an acidic environment (36% Mn loss determined) than in a slightly alkaline environment (27% Mn loss). Enzymatic degradation of PCL-b-PDMAEMA, poly(d,l-lactide)-block-poly(N,N'-dimethylaminoethyl methacrylate) (PLA-b-PDMAEMA) and poly(lactide-co-glycolide-co-ε-caprolactone)-block-poly(N,N'-dimethylaminoethyl methacrylate) (PLGC-b-PDMAEMA) and the corresponding aliphatic polyesters (PCL, PLA and PLGC) was performed by Novozyme 435. In enzymatic degradation, PLGC degraded almost completely after eleven days. For polyester-b-PDMAEMA copolymers, enzymatic degradation primarily involved the ester bonds in PDMAEMA side chains, and the rate of polyester degradation decreased with the increase in the chain length of PDMAEMA. Amphiphilic copolymers might be used for biomaterials with long-term or midterm applications such as nanoscale drug delivery systems with tunable degradation kinetics.

PDMAEMA/Polyester Miktopolymers: Synthesis via In-Out Approach, Physicochemical Characterization and Enzymatic Degradation.

Synthesis, physicochemical characterization, and the enzymatic degradation of the amphiphilic miktoarm star-shaped polymers is reported herein. First, star-shaped macroinitiators, based on N,N'-dimethylaminoethyl methacrylate (DMAEMA) and glycerol dimethacrylate (GDMA) ((PDMAEMA)n-PGDMA), were synthesized. Due to the presence of hydroxyl groups in the macroinitiator core, polyesters such as poly(ɛ-caprolactone) (P(ɛ-CL)), polylactide (PLA) and poly(lactide-co-glycolide) (PLGA) were synthesized using ring opening polymerization (ROP). Comprehensive degradation studies on enzymatic degradation, using a lipase from Pseudomonas cepacia, were performed. Enzymatic degradation was monitored by weight measurements and nuclear magnetic resonance spectroscopy (1H NMR). The fastest degradation rate was observed for the polymer with the lowest molecular weight. Amphiphilic miktopolymers may find application as biomaterials for long- or mid-term period drug-delivery systems.

Temperature and pH-Dependent Response of Poly(Acrylic Acid) and Poly(Acrylic Acid-co-Methyl Acrylate) in Highly Concentrated Potassium Chloride Aqueous Solutions.

In this study, the phase transition phenomena of linear poly(acrylic acid) (PAA) and linear or star-shaped poly(acrylic acid-co-methyl acrylate) (P(AA-co-MA)) in highly concentrated KCl solutions were investigated. The effects of polymer molecular weight, topology, and composition on their phase transition behavior in solution were investigated. The cloud point temperature (TCP) of polymers drastically increased as the KCl concentration (CKCl) and solution pH increased. CKCl strongly influenced the temperature range at which the phase transition of PAA occurred: CKCl of 1.0-2.2 M allowed the phase transition to occur between 30 and 75 °C. Unfortunately, at CKCl above 2.6 M, the TCP of PAA was too high to theoretically trigger the crystallization of KCl. The addition of hydrophobic methyl acrylate moieties decreased the TCP into a temperature region where KCl crystallization could occur. Additionally, the hydrodynamic diameters (Dh) and zeta potentials of commercial PAA samples were examined at room temperature and at their TCP using dynamic light scattering. The salt concentration (from 1 to 3 M) did not impact the hydrodynamic diameter of the molecules. Dh values were 1500 and 15 nm at room temperature and at TCP, respectively.

Pressure-assisted solvent- and catalyst-free production of well-defined poly(1-vinyl-2-pyrrolidone) for biomedical applications.

In this work, we developed a fast, highly efficient, and environmentally friendly catalytic system for classical free-radical polymerization (FRP) utilizing a high-pressure (HP) approach. The application of HP for thermally-induced, bulk FRP of 1-vinyl-2-pyrrolidone (VP) allowed to eliminate the current limitation of ambient-pressure polymerization of 'less-activated' monomer (LAM), characterized by the lack of temporal control yielding polymers of unacceptably large disperisites and poor result reproducibility. By a simple manipulation of thermodynamic conditions (p = 125-500 MPa, T = 323-333 K) and reaction composition (two-component system: monomer and low content of thermoinitiator) well-defined poly(1-vinyl-2-pyrrolidone)s (PVP) in a wide range of molecular weights and low/moderate dispersities (M n = 16.2-280.5 kg mol-1, D = 1.27-1.45) have been produced. We have found that HP can act as an 'external' controlling factor that warrants the first-order polymerization kinetics for classical FRP, something that was possible so far only for reversible deactivation radical polymerization (RDRP) systems. Importantly, our synthetic strategy adopted for VP FRP enabled us to obtain polymers of very high M n in a very short time-frame (0.5 h). It has also been confirmed that VP bulk polymerization yields polymers with significantly lower glass transition temperatures (T g) and different solubility properties in comparison to macromolecules obtained during the solvent-assisted reaction.

Synthesis and in vitro cytotoxicity evaluation of star-shaped polymethacrylic conjugates with methotrexate or acitretin as potential antipsoriatic prodrugs.

Water-soluble polymer-drug conjugates were obtained and analyzed towards their potential use as prodrugs for two hydrophobic antipsoriatic agents, including methotrexate (MTX) and acitretin (AC). The conjugation efficacy of MTX decreased with a decreasing molar ratio of N,N-dimethylaminoethyl methacrylate (DMAEMA) repeating units in the polymethacrylic chains. Cytotoxicity of positively charged (from +5 to +10 mV) nano- and microparticles (3-1500 nm in DMEM at 37 °C) were estimated by in vitro MTT and Annexin-V apoptosis assays on Me45, NHDF, HaCaT and BEAS-2B cell lines. Further, cell cycle analysis revealed arrest in G0/G1 phase in melanoma cells, while neither apoptosis induction nor cell cycle arrest occurred in normal epidermal and epithelial cells. Tested conjugates displayed a novel cytostatic effect in Me45 cells and a pro-apoptotic effect in HaCaT cells. Epithelial BEAS-2B cells were the most sensitive to the tested conjugates and responded via induction of necrosis. Cell line models allowed for characterization of the biologically relevant potential action of pro-drugs. Additionally, a skin in vitro evaluation assay provided the first known evidence of side-effect reduction with pro-drug use. Histological examinations confirmed the lack of negative effects of conjugates on the skin and showed no irritating properties.

Choline supported poly(ionic liquid) graft copolymers as novel delivery systems of anionic pharmaceuticals for anti-inflammatory and anti-coagulant therapy.

New type of carriers based on grafted poly(ionic liquid)s was designed for delivery of ionically attached salicylates (Sal). Choline derived ionic liquid monomeric units were successfully introduced with various content in the side chains by the controlled radical polymerization. Properly high amounts of ionic pharmaceutics in the polymer systems were achieved by the well-fitted length and grafting degree of the side chains. In aqueous solution the graft copolymers were self-assembled into the spherical superstructures with sizes up to 73 nm. Delivery studies showed "burst" release within 4 h, after that it was slower yielding ~70% of released drug within 80 h. Proposed nanocarriers supported low toxicity against human cells (NHDF and BEAS-2B), anti-inflammation activity evaluated with the use of pro-inflammatory interleukins (IL-6 and IL-8) and antibacterial activities towards E. coli. Adjustment of ionic drug content by structural parameters of graft copolymers, including grafting degree and graft length, are advantageous to tailor nanocarriers with self-assembly properties in aqueous media. Effective release process by ionic exchange and biological activity with low toxicity are promising for further development of this type of drug delivery (DDS).

Retinol-Containing Graft Copolymers for Delivery of Skin-Curing Agents.

The new polymeric systems for delivery in cosmetology applications were prepared using self-assembling amphiphilic graft copolymers. The synthesis based on "click" chemistry reaction included grafting of azide-functionalized polyethylene glycol (PEG-N3) onto multifunctional polymethacrylates containing alkyne units. The latter ones were obtained via atom transfer radical polymerization (ATRP) of alkyne-functionalized monomers, e.g., ester of hexynoic acid and 2-hydroxyethyl methacrylate (AlHEMA) with methyl methacrylate (MMA), using bromoester-modified retinol (RETBr) as the initiator. Varying the content of alkyne moieties adjusted by initial monomer ratios of AlHEMA/MMA was advantageous for the achievement of a well-defined grafting degree. The designed amphiphilic graft copolymers P((HEMA-graft-PEG)-co-MMA), showing tendency to micellization in aqueous solution at room temperature, were encapsulated with arbutin (ARB) or vitamin C (VitC) with high efficiencies (>50%). In vitro experiments carried out in the phosphate-buffered saline solution (PBS) at pH 7.4 indicated the maximum release of ARB after at least 20 min and VitC within 10 min. The fast release of the selected antioxidants and skin-lightening agents by these micellar systems is satisfactory for applications in cosmetology, where they can be used as the components of masks, creams, and wraps.

Ionic Polymethacrylate Based Delivery Systems: Effect of Carrier Topology and Drug Loading.

The presented drug delivery polymeric systems (DDS), i.e., conjugates and self-assemblies, based on grafted and star-shaped polymethacrylates have been studied for the last few years in our group. This minireview is focused on the relationship of polymer structure to drug conjugation/entrapment efficiency and release capability. Both graft and linear polymers containing trimethylammonium groups showed the ability to release the pharmaceutical anions by ionic exchange, but in aqueous solution they were also self-assembled into nanoparticles with encapsulated nonionic drugs. Star-shaped polymers functionalized with ionizable amine/carboxylic groups were investigated for drug conjugation via ketimine/amide linkers. However, only the conjugates of polybases were water-soluble, giving opportunity for release studies, whereas the self-assembling polyacidic stars were encapsulated with the model drugs. Depending on the type of drug loading in the polymer matrix, their release rates were ordered as follows: Physical ≥ ionic > covalent. The studies indicated that the well-defined ionic polymethacrylates, including poly(ionic liquid)s, are advantageous for designing macromolecular carriers due to the variety of structural parameters, which are efficient for tuning of drug loading and release behavior in respect to the specific drug interactions.

The application of spatially restricted geometries as a unique route to produce well-defined poly(vinyl pyrrolidones) via free radical polymerisation.

We report, for the first time, the metal-free green synthesis of linear poly(vinyl pyrrolidone) (PVP) homopolymers of molecular weight higher than 100 kg mol-1 and narrow dispersities via thermal and photo-induced free radical polymerisation carried out within alumina nanoporous membranes acting as "nanoreactors".

Self-assembling water-soluble polymethacrylate-MTX conjugates: The significance of macromolecules architecture on drug conjugation efficiency, the final shape of particles, and drug release.

Water-soluble polymer-methotrexate (MTX) conjugates were obtained via efficient carbodiimide-mediated amidation (E = 17-100%). Binding abilities between water-soluble V-shaped or star-shaped copolymers and MTX were studied by isothermal titration calorimetry spectroscopic (UV-vis, NMR) and microscopic (scanning electron microscopy and transmission electron microscopy) techniques. The efficiency of the amidation reaction has depended on the amount of pendant amino alcohol groups and zeta potential (ZP) values of polymeric carries. The sizes of aggregates formed by polymer-drug conjugates in water increased with the number of copolymer arms (202-774 nm at 37°C). Moreover, the conjugates with the high amount of bounded MTX molecules (nMTX > 78) exhibited negative ZP values. The drug release experiments revealed that the amount of the released MTX depends on pH and can be controlled via shape, topology, and composition of polymeric carrier. Preliminary cytotoxicity studies of V-shaped-MTX conjugate on human immortalized nontumorigenic keratinocyte (HaCaT) cells indicated cytocompatibility of the compound in a wide range of concentrations. The results of our studies have shown that physicochemical and drug release properties of obtained polymer-MTX prodrugs can be tailored via the structure and the topology of the polymeric carrier. Thus conjugates might find the application in a different type of treatment (cancer or psoriasis therapy) and administration (intravenous, dermal, or pulmonary). © 2019 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 107B:2476-2487, 2019.