RESUMEN
The vertebral column represents an essential element for support, mobility, and the protection of the central nervous system. Various pathologies can compromise these vital functions, leading to pain and a decrease in the quality of life. Within the scope of this study, a novel redesign of the Intersomatic Cage, traditionally used in the presence of discopathy, was proposed. The adoption of additive manufacturing technology allowed for the creation of highly complex geometries, focusing on the lumbosacral tract, particularly on the L4-L5 and L5-S1 intervertebral discs. In addition to the tensile analysis carried out using Finite Element Analysis (FEA) in static simulations, a parallel study on the range of motion (ROM) of the aforementioned vertebral pairs was conducted. The ROM represents the relative movement range between various vertebral pairs. The introduction of the intersomatic cage between the vertebrae, replacing the pulpy nucleus of the intervertebral disc, could influence the ROM, thus having significant clinical implications. For the analysis, the ligaments were modelled using a 1D approach. Their constraint reaction and deformability upon load application were analysed to better understand the potential biomechanical implications arising from the adoption of the cages. During the FEA simulations, two types of cages were analysed: LLIF for L4-L5 and ALIF for L5-S1, subjecting them to four different loading conditions. The results indicate that the stresses exhibited by cages with a NET structure are generally lower compared to those of traditional cages. This stress reduction in cages with NET structure suggests a more optimal load distribution, but it is essential to assess potential repercussions on the surrounding bone structure.
RESUMEN
In this research, a new lattice structure based on the octagonal geometry and produced by Additive Manufacturing (AM) technique was proposed. Eight octagons with the same dimensions are combined to each other forming a ring. To obtain an isotropic lattice structure, cubic symmetry was imposed; thus, the unit cell is made of three rings mutually perpendicular, one ring for each principal direction. The aim of this study is the morphological and mechanical characterization of the novel unit cell to check its suitability to the biomechanical field, along with its comparison with other lattice structures currently used as bone scaffold. Electron Beam Melting (EBM) technique was used to produce Ti6Al4V ELI alloy specimens of the novel unit cell and of the truncated octahedron (Kelvin) cell. Three different unit cell sizes were selected to investigate the effect of cell dimensions on the mechanical properties. Morphological analysis was performed through a scanning electron microscope (SEM), to compare the actual structures to the designed ones. On the whole, the new lattice structure provided adequate mechanical properties to be considered as a bone substitute; further tests will be focused on its osteointegration capability.
Asunto(s)
Biomimética , Huesos , Porosidad , Ensayo de Materiales , Prótesis e Implantes , Aleaciones , Titanio/químicaRESUMEN
The lumbar intervertebral devices are widely used in the surgical treatment of lumbar diseases. The subsidence represents a serious clinical issue during the healing process, mainly when the interfaces between the implant and the vertebral bodies are not well designed. The aim of this study is the evaluation of subsidence risk for two different devices. The devices have the same shape, but one of them includes a filling micro lattice structure. The effect of the micro lattice structure on the subsidence behavior of the implant was evaluated by means of both experimental tests and finite element analyses. Compressive tests were carried out by using blocks made of grade 15 polyurethane, which simulate the vertebral bone. Non-linear, quasi-static finite element analyses were performed to simulate experimental and physiologic conditions. The experimental tests and the FE analyses showed that the subsidence risk is higher for the device without micro lattice structure, due to the smaller contact surface. Moreover, an overload in the central zone of the contact surface was detected in the same device and it could cause the implant failure. Thus, the micro lattice structure allows a homogenous pressure distribution at the implant-bone interface.
Asunto(s)
Vértebras Lumbares , Fusión Vertebral , Vértebras Lumbares/cirugía , Titanio , Porosidad , Electrones , Prótesis e ImplantesRESUMEN
BACKGROUND: External ventricular drain (EVD) placement is mandatory for several pathologies. The misplacement rate of the EVD varies widely in literature, ranging from 12.3 to 60%. The purpose of this simulation study is to provide preliminary data about the possibility of increasing the safety of one of the most common life-saving procedures in neurosurgery by testing a new device for EVD placement. METHODS: We used a novel guide for positioning the ventricular catheter (patent RM2014A000376). The trajectory was assessed using 25 anonymized head CT scans. The data sets were used to conduct three-dimensional computer-based and combined navigation and augmented reality-based simulations using plaster models. The data set inclusion criteria were volumetric head CT scan, without midline shift, of patients older than 18. Evans' index was used to quantify the ventricle's size. We excluded patients with slit ventricles, midline shift, skull fractures, or complex skull malformations. The proximal end of the device was tested on the cadaver. RESULTS: The cadaveric tests proved that a surgeon could use the device without any external help. The multimodal simulation showed Kakarla grade 1 in all cases but one (grade 2) on both sides, after right and left EVD placement. The mean Evans' index was 0.28. The geometric principles that explain the device's efficacy can be summarized by studying the properties of circumference and chord. The contact occurs, for each section considered, at the extreme points of the chord. Its axis, perpendicular to the plane tangent to the spherical surface at the entry point, corresponds to the direction of entry of the catheter guided by the instrument. CONCLUSION: According to our multimodal simulation on cadavers, 3D computer-based simulation, 3D plaster modeling, 3D neuronavigation, and augmented reality, the device promises to offer safer and effective EVD placement. Further validation in future clinical studies is recommended.
RESUMEN
The aim of this study was the analysis of the mechanical behaviour of a partially porous lumbar custom-made cage by means of a subject-specific finite element analysis (FEA). The cage, made of Ti6Al4V ELI alloy, was produced via electron beam melting (EBM) process and surgically implanted in a female subject, 50 years old. The novelty of this study was the customized design of the cage and of its internal structure, which is impossible to obtain with the traditional production techniques. The 3D model of the spine was obtained from the computed tomography (CT) of the patient. Moreover, high-resolution industrial CT was also used to reconstruct a 3D model of the cage, with its real (as-produced) features, such as superficial roughness, morphology of the bulk and of the porous structure. The workflow was divided in several steps: the main finite element analyses were non-linear and quasi-static regarding: the rhombic dodecahedron (RD) unit cell of the porous structure; the device; the whole L4-L5 motion segment with the implanted cage. Stress distribution was calculated under compression load for all models. For the RD unit cell, the maximum stress appeared at the connected cross nodes, where notch effect was present. For the cage subjected to a load of 1 kN, the porous structure did not present any functional failure. For the whole biomechanical system subjected to a physiological load of 360 N, the calculated stress in the bone was smaller than its yield strength value. On the axial view, a zone with higher compressive stresses was present on the L5 vertebral body. This was due to the contact stress between the cage and the vertebra. From the comparison between FE results and the CT images of the spine, bone remodelling was supposed, with the formation of new bone. Graphical abstract Workflow showing the phases of the research.