A sodium ion conducting gel polymer electrolyte with counterbalance between 1-ethyl-3-methylimidazolium tetrafluoroborate and tetra ethylene glycol dimethyl ether for electrochemical applications.

For sodium batteries, the development of gel polymer electrolytes (GPEs) with remarkable electrochemical properties is in its early stage and persists to be a challenge. In this report we have synthesized a series of GPEs containing a poly(vinyllidene fluoride-co-hexafluoropropylene) (PVdF-HFP) and poly (methyl methacrylate) (PMMA) as blend polymer, sodium perchlorate (NaClO4) as ion-conducting salt and 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIM-BF4) and tetra ethylene glycol dimethyl ether (TEGDME) as molecular solvents. The counter balance between EMIM-BF4 and TEGDME is maintained by the electrolyte, which is formed through the optimal weight ratio of 2 : 1. GPEs have an advantageous set of properties, including stability window of 5 V, Na+ transference number of 0.20, and a room-temperature ionic conductivity of 5.8 × 10-3 S cm-1. According to enthalpy and entropy calculations, optimized GPE yields the highest amount of disorder or amorphicity and contributes to greatest conductivity. XRD analysis supports this argument. Thermal investigations show that optimized GPE may preserve gel phase up to 125 °C. The prototype sodium cell fabricated with optimize GPE has a specific capacity of 281 mA h g-1 and open circuit voltage of 2.5 V. The optimized GPE exhibits potential for future electrochemical applications.

Electrochemical and Ion Transport Studies of Li+ Ion-Conducting MC-Based Biopolymer Blend Electrolytes.

A facile methodology system for synthesizing solid polymer electrolytes (SPEs) based on methylcellulose, dextran, lithium perchlorate (as ionic sources), and glycerol (such as a plasticizer) (MC:Dex:LiClO4:Glycerol) has been implemented. Fourier transform infrared spectroscopy (FTIR) and two imperative electrochemical techniques, including linear sweep voltammetry (LSV) and electrical impedance spectroscopy (EIS), were performed on the films to analyze their structural and electrical properties. The FTIR spectra verify the interactions between the electrolyte components. Following this, a further calculation was performed to determine free ions (FI) and contact ion pairs (CIP) from the deconvolution of the peak associated with the anion. It is verified that the electrolyte containing the highest amount of glycerol plasticizer (MDLG3) has shown a maximum conductivity of 1.45 × 10-3 S cm-1. Moreover, for other transport parameters, the mobility (µ), number density (n), and diffusion coefficient (D) of ions were enhanced effectively. The transference number measurement (TNM) of electrons (tel) was 0.024 and 0.976 corresponding to ions (tion). One of the prepared samples (MDLG3) had 3.0 V as the voltage stability of the electrolyte.

Improving EDLC Device Performance Constructed from Plasticized Magnesium Ion Conducting Chitosan Based Polymer Electrolytes via Metal Complex Dispersion.

The current work shows the preparation of plasticized chitosan-magnesium acetate Mg(CH3COO)2-based polymer electrolyte dispersed with nickel (Ni) metal complexes via solution casting. Investigations of electrical and electrochemical properties of the prepared polymer composite electrolyte were carried out. The structural and optical properties of the samples were studied using X-ray diffraction (XRD) and UV-Vis spectroscopy techniques. The structural and optical outcomes revealed a clear enhancement in both absorbance and amorphous nature of the samples upon the addition of Ni metal complexes. Through the simulation of impedance data, various ion transport parameters were calculated. The electrochemical performance of the sample was examined by means of transference number measurement (TNM), linear sweep voltammetry (LSV) and cyclic voltammetry (CV) measurements. The TNM analysis confirmed the dominance of ions as the main charge carrier in the electrolyte with tion of (0.96) compared to only (0.04) for tel. The present electrolyte was stable in the range of 0 V to 2.4 V, which was obtained from linear sweep voltammetry (LSV). A result from CV proved that the electrical double-layer capacitor (EDLC) has a capacitive behavior as no redox peaks could be observed. The presence of Ni improved the charge-discharge cycle of the EDLC due to its amorphous behavior. The average performances of the EDLC were recorded as 41.7 F/g, 95%, 5.86 Wh/kg and 628 W/kg for specific capacitance, coulombic efficiency, energy and power densities, respectively. The fabricated EDLC device was found to be stable up to 1000 cycles.