Effect of Two Polishing Systems on Surface Roughness, Topography, and Flexural Strength of a Monolithic Lithium Disilicate Ceramic.

PURPOSE: To evaluate the effect of overglazing and two polishing procedures on flexural strength and quality and quantity of surface roughness of a monolithic lithium disilicate ceramic computer-aided design (CAD) after grinding. MATERIALS AND METHODS: This in vitro study was conducted on 52 partially crystalized bar-shaped specimens (16 × 4 × 1.6 mm) of monolithic lithium disilicate ceramic. The specimens were wet polished with 600-, 800-, and 1200-grit silicon carbide papers for 15 seconds using a grinding/polishing machine at a speed of 300 rpm. Then, the specimens were crystalized and glaze-fired in one step simultaneously and randomly divided into four groups of 13: (I) Glazing group (control); (II) Grinding-glazing group, subjected to grinding with red band finishing diamond bur (46 µm) followed by glazing; (III) Grinding-D+Z group, subjected to grinding and then polishing by coarse, medium, and fine diamond rubber points (D+Z); and (IV) Grinding-OptraFine group, subjected to grinding and then polishing with a two-step diamond rubber polishing system followed by a final polishing step with an OptraFine HP brush and diamond polishing paste. The surface roughness (Ra and Rz) values (µm) were measured by a profilometer, and the mean values were compared using one-way ANOVA and Tamhane's test (post hoc comparison). One specimen of each group was evaluated under a scanning electron microscope (SEM) for surface topography. The three-point flexural strength values of the bars were measured using a universal testing machine at a 0.5 mm/min crosshead speed and recorded. The data were analyzed using one-way ANOVA and Tamhane's test (α = 0.05). RESULTS: Statistically significant differences were noted among the experimental groups for Ra, Rz (p < 0.0001), and flexural strength values (p < 0.009). The lowest Ra and Rz values were found in the grinding-OptraFine group (0.465 ± 0.153), which were significantly lower than those in glazing (p < 0.03) and grinding-glazing (p < 0.001) groups. The Ra and Rz values were not significantly different between the two polishing systems (p = 0.23 and p = 0.25, respectively). The highest flexural strength was found in the glazing group (283.350 ± 49.854 MPa) without significant differences compared to grinding-glazing (p = 0.98) and grinding-OptraFine groups (p = 0.86). The lowest flexural strength was found in grinding-D+Z group (225.070 ± 17.299), which was significantly different from the value in glazing (p < 0.03) and grinding-glazing (p < 0.04) groups. SEM analysis of polished surfaces revealed regular morphology with some striations. CONCLUSIONS: The OptraFine system created smoother and more uniform surfaces in terms of quantity (p < 0.03 for Ra, p < 0.01 for Rz) and quality of roughness compared to glazing. The flexural strength of lithium disilicate ceramic after polishing with the OptraFine system was similar to that after glazing (p = 0.86). Despite similar surface roughness after polishing with the two systems, the D+Z system reduced the flexural strength of ceramic (p < 0.03).

Antibacterial Effect of Hydroalcoholic Extract of Punica granatum Linn. Petal on Common Oral Microorganisms.

Objectives. This study aimed to assess the effect of hydroalcoholic extract of Punica granatum Linn. (P. granatum) petal on Streptococcus sanguinis, Streptococcus mutans, Streptococcus salivarius, Streptococcus sobrinus, and Enterococcus faecalis. Materials and Methods. In this in vitro study, P. granatum extract was prepared using powdered petals and water-ethanol solvent. Antibacterial effect of the extract, chlorhexidine (CHX), and ampicillin was evaluated on brain heart infusion agar (BHIA) using the cup-plate method. By assessing the diameter of the growth inhibition zone, the minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) of the extract were determined for the above-mentioned bacteria. Results. Hydroalcoholic extract of P. granatum petal had inhibitory effects on the proliferation of all five bacterial strains with maximum effect on S. mutans with MIC and MBC of 3.9 mg/mL. The largest growth inhibition zone diameter belonged to S. sanguinis and the smallest to E. faecalis. Ampicillin and CHX had the greatest inhibitory effect on S. sanguinis. Conclusions. Hydroalcoholic extract of P. granatum had a significant antibacterial effect on common oral bacterial pathogens with maximum effect on S. mutans, which is the main microorganism responsible for dental plaque and caries.

Surface topography and bond strengths of feldspathic porcelain prepared using various sandblasting pressures.

OBJECTIVE: The purpose of this study was to determine the bond strength of composite resin to feldspathic porcelain and its surface topography after sandblasting at different pressures. METHODS: In this in vitro study, 68 porcelain disks were fabricated and randomly divided into four groups of 17. The porcelain surface in group 1 was etched with hydrofluoric acid. Groups 2, 3, and 4 were sandblasted at 2, 3 and 4 bars pressure, respectively. Surface topography of seven samples in each of the four groups was examined by a scanning electron microscope (SEM). The remaining 40 samples received the same silane agent, bonding agent, and composite resin and they were then subjected to 5000 thermal cycles and evaluated for shear bond strength. Data were analyzed using one-way anova. The mode of failure was determined using stereomicroscope and SEM. RESULTS: The highest shear bond strength was seen in group 4. however, statistically significant differences were not seen between the groups (P = 0.780). The most common mode of failure was cohesive in porcelain. The SEM showed different patterns of hydrofluoric acid etching and sandblasting. CONCLUSION: Increasing the sandblasting pressure increased the surface roughness of feldspathic porcelain but no difference in bond strength occurred.

Relationship of Gingival Pigmentation with Passive Smoking in Women.

BACKGROUND: Oral mucosal pigmentation is among the most common findings in smokers, affecting smile esthetics. Passive smoking significantly compromises the health of non-smoker individuals particularly women. The purpose of this study was to assess the relationship of passive smoking with oral pigmentation in non-smoker women. MATERIALS AND METHODS: This historical-cohort study was conducted on a case group of 50 married women who were unemployed, not pregnant, non-smoker, had no systemic condition causing cutaneous or mucosal pigmentation, were not taking any medication causing cutaneous or mucosal pigmentation and had a heavy smoker husband. The control group comprised of 50 matched females with no smoker member in the family. Both groups were clinically examined for presence of gingival pigmentation and the results were analyzed using chi-square and logistic regression tests. RESULTS: Gingival pigmentation was found in 27 (54%) passive smokers and 14 (28%) controls (P=0.01). The odds ratio (OR) of gingival pigmentation in women exposed to secondhand smoke of their husbands (adjusted for education and having a smoker parent at childhood) was 3 (95% confidence interval; CI: 1.26 - 7.09). House floor area was correlated with gingival pigmentation in female passive smokers (P=0.025). CONCLUSION: This study was the first to describe the relationship between secondhand smoke and gingival pigmentation in women and this effect was magnified in smaller houses.

Effect of Extension and Type of Composite-Restored Class II Cavities on Biomechanical Properties of Teeth: A Three Dimensional Finite Element Analysis.

OBJECTIVES: Controversy exists regarding cavity preparation for restoration of interproximal caries in posterior teeth in terms of preserving the tooth structure and suitable stress distribution. This study aimed to assess the effect of extension and type of class II cavities and the remaining tooth structure in maxillary premolars restored with composite resin on the biomechanical properties of teeth using finite element method (FEM). MATERIALS AND METHODS: Using FEM, eight three-dimensional (3D) models of class II cavities in maxillary premolars with variable mesiodistal (MD) dimensions, variable thickness of the residual wall in-between the mesial and distal cavities and different locations of the wall were designed. Other dimensions were the same in all models. Cavities were restored with composite resin. A load equal to the masticatory force (200N) was applied to the teeth. Finite element analysis (FEA) was used to calculate the von Mises stress. RESULTS: Stress in the enamel margin increased by increasing the MD dimensions of the cavities. Deviation of the residual wall between the mesial and distal cavities from the tooth center was found to be an important factor in increasing stress concentration in the enamel. Increasing the MD dimensions of the cavity did not cause any increase in stress concentration in dentin. CONCLUSION: Increasing the MD dimensions of the cavities, decreasing the thickness of the residual wall between the mesial and distal cavities and its deviation from the tooth center can increase stress concentration in the enamel but not in dentin.

Anbarnesa: The Past Tradition, the Future Medicine.

CONTEXT: In the Iranian traditional medicine, anbarnesa smoke derived from burning female donkey's dung has long been used for treatment of inflammatory ulcers and infections of the middle and external ear with no significant side effects. The aim of this study was to introduce anbarnesa and discuss its therapeutic effects. EVIDENCE ACQUISITION: We conducted a systematic search in PubMed, Medline, Google, and Google Scholar databases to find studies on anbarnesa. The keywords searched were as follows: "anbarnesa," "traditional medicine," "medicinal smoke," "donkey," "dung," "antimicrobial," "inflammation," "infection," and "cytotoxicity. RESULTS: Literature review reveals that ANNAS (anbarnesa smoke) enhances wound healing, decreases scar formation, inhibits growth of cancer cells (Hela and KB) and has antimicrobial properties. Also, ANNAS combined with propylene glycol is nontoxic in 1/64, 1/128, and 1/256 dilutions. CONCLUSIONS: The constituents of anbarnesa smoke mainly possess antibacterial, anti-inflammatory, and growth inhibition effects on cancer cells.

Surface treatment of feldspathic porcelain: scanning electron microscopy analysis.

PURPOSE: Topographic analysis of treated ceramics provides qualitative information regarding the surface texture affecting the micromechanical retention and locking of resin-ceramics. This study aims to compare the surface microstructure following different surface treatments of feldspathic porcelain. MATERIALS AND METHODS: This in-vitro study was conducted on 72 porcelain discs randomly divided into 12 groups (n=6). In 9 groups, feldspathic surfaces were subjected to sandblasting at 2, 3 or 4 bar pressure for 5, 10 or 15 seconds with 50 µm alumina particles at a 5 mm distance. In group 10, 9.5% hydrofluoric acid (HF) gel was applied for 120 seconds. In group 11, specimens were sandblasted at 3 bar pressure for 10 seconds and then conditioned with HF. In group 12, specimens were first treated with HF and then sandblasted at 3 bar pressure for 10 seconds. All specimens were then evaluated under scanning electron microscopy (SEM) at different magnifications. RESULTS: SEM images of HF treated specimens revealed deep porosities of variable sizes; whereas, the sandblasted surfaces were more homogenous and had sharper peaks. Increasing the pressure and duration of sandblasting increased the surface roughness. SEM images of the two combined techniques showed that in group 11 (sandblasted first), HF caused deeper porosities; whereas in group 12 (treated with HF first) sandblasting caused irregularities with less homogeneity. CONCLUSION: All surface treatments increased the surface area and caused porous surfaces. In groups subjected to HF, the porosities were deeper than those in sandblasted only groups.