Technical Skills Influences on Front Crawl Tumble Turn Performance in Elite Female Swimmers.

The objective of this research was to compare technical skills composed of kinematic and kinetic variables in the complex motor task of a tumble turn between 9 elites and 9 sub-elite female swimmers. The best tumble turn among three attempts was analyzed using a three-dimensional underwater protocol. A total of 37 kinematic variables were derived from a Direct Linear Transformation algorithm for 3D reconstruction, and 16 kinetic variables measured by a piezoelectric 3D force platform. Data were analyzed by Student's t-test and effect size statistics. Pearson correlations were applied to the data of the eighteen swimmers to relate the association of 53 kinematic, kinetic variables to the performance of the tumble-turn (3 meters Round Trip Time, 3m RTT). The approach and the whole turn times were faster for elite swimmers compared to sub elites (1.09±0.06 vs. 1.23±0.08 sec, and 2.89±0.07 vs. 3.15±0.11 sec.), as well as the horizontal speeds of the swimmers' head 1 m before the rotation (1.73±0.13 vs. 1.57±0.13 m/sec.), at the end of the push-off on force platform (2.55±0.15 vs. 2.31±0.22 m/sec.) and 3 m after the wall (2.01±0.19 vs. 1.68±0.12 m/sec.). Large differences (|d| > 0.8) in favor of the elite swimmers were identified for the index of upper body extension at the beginning of the push-off, the lower limb extension index at the end of push-off, and among the kinetic variables, the horizontal impulse and lateralization of the push-off. Correlations for the whole group revealed a moderate to strong relationship between 6 body extension indices and 3mRTT performance. For the kinetic variables, the correlations indicated the fastest swimmers in 3mRTT showed large lateral impulse during placement (r=0.46), maximum horizontal force during the push-off (r=0.45) and lateralization of the push-off (r=0.44) (all p<0.05). Elite female swimmers had higher approach and push-off speeds, were more streamlined through the contact, and showed a higher horizontal impulse and lateralization of the push-off, than their sub-elite counterparts.

Kinematic and dynamic analyses of the front crawl tumble turn in elite female swimmers.

Based on a three-dimensional (3D) underwater analysis, the objective of the present study was to identify the biomechanical variables the most associated with turn times in 10 elite female swimmers. For each participant (95.7 ± 2.6% of the 200 m freestyle world record), the best-time turn (from 3 m in to 3 m out, 2.89 ± 0.08 s) was analysed from a three-dimensional (3D) direct linear transformation kinematical reconstruction and the use of a piezoelectric force platform. Bivariate analysis showed that lateral impulse was linked to turn time (r = -0.76, p = 0.01) as well as horizontal velocities at end of the glide and swim resumption (respectively, 1.88 ± 0.2 m·s-1 and 1.48 ± 0.15 m·s-1; r = -0.67 and -0.68; p < 0.05 for both variables). One variable was considered relevant in the best Lasso (Least Absolute Shrinkage and Selection Operator) model: the lateral impulse (8.8 ± 5.1 N·s) during the placement sub-phase.The best tumble turn times were associated with higher lateral impulse during the placement and faster velocities during the underwater actions. The lateral impulse may reflect the swimmers' longitudinal rotation which was higher for the fastest swimmers.

Biomechanical analysis comparing natural and alloplastic temporomandibular joint replacement using a finite element model.

PURPOSE: Prosthetic materials and bone present quite different mechanical properties. Consequently, mandible reconstruction with metallic materials (or a mandible condyle implant) modifies the physiologic behavior of the mandible (stress, strain patterns, and condyle displacements). The changing of bone strain distribution results in an adaptation of the temporomandibular joint, including articular contacts. MATERIALS AND METHODS: Using a validated finite element model, the natural mandible strains and condyle displacements were evaluated. Modifications of strains and displacements were then assessed for 2 different temporomandibular joint implants. Because materials and geometry play important key roles, mechanical properties of cortical bone were taken into account in models used in finite element analysis. RESULTS: The finite element model allowed verification of the worst loading configuration of the mandibular condyle. Replacing the natural condyle by 1 of the 2 tested implants, the results also show the importance of the implant geometry concerning biomechanical mandibular behavior. The implant geometry and stiffness influenced mainly strain distribution. CONCLUSION: The different forces applied to the mandible by the elevator muscles, teeth, and joint loads indicate that the finite element model is a relevant tool to optimize implant geometry or, in a subsequent study, to choose a more suitable distribution of the screws. Bone screws (number and position) have a significant influence on mandibular behavior and on implant stress pattern. Stress concentration and implant fracture must be avoided.

Pole-vaulting: identification of the pole local bending rigidities by an updating technique.

The development of composite material poles since 1960 has played a prominent part in performance improvement in pole-vaulting. Previous studies devoted to pole-vaulting models were based on constant mechanical characteristics. It is thus necessary to identify the local bending rigidities of the pole to build realistic pole-vaulting models. Updating methods developed for dynamic structure studies allow us to describe local mechanical characteristics. These methods are based on the comparison between experimental results and those determined numerically by finite element models. This study presents an adaptation of these methods to determine the local bending rigidities of the pole. The updating technique is validated by a deflection test of a homogeneous beam. Then, a study of the model sensitivity is carried out to investigate the procedure robustness. Finally, the updating method is applied to an old design pole and to a recent one. The results obtained vary greatly from one pole to the other; they highlight the evolutions in pole design.

Influence of the moment exerted by the athlete on the pole in pole-vaulting performance.

Current studies on pole-vaulting focus mostly on energy transfer data [Ekevad, M., Lundberg, B., 1995. Simulation of "smart" pole vaulting. Journal of Biomechanics 28, 1079-1090; Ekevad, M., Lundberg, B., 1997. Influence of pole length and stiffness on the energy conversion in pole-vaulting. Journal of Biomechanics, 30, 259-264; Linthorne, N.P., 2000. Energy loss in the pole vault take-off and the advantage of the flexible pole. Sports Engineering 3, 205-218; Schade, F., Arampatzis, A., Bruggemann, G.P., 2006. Reproducibility of energy parameters in the pole vault. Journal of Biomechanics 39, 146-147.] and often fail to take into account the actions exerted on the pole [Arampatzis, Schade, Bruggemann, 2004. Effect of the pole-human body interaction on pole-vaulting performance. Journal of Biomechanics 37, 1353-1360]. The present study integrates the 3D kinematics data of the athlete but also the actions measured at the end of the pole in the planting box and on the track during the last stride before take-off. It proposes a mechanical model allowing determination of the pole-vaulter's actions on the pole. The model is based on a global mechanical approach. The pole-vaulter's action on his upper and lower hand is concentrated on one middle point to solve the dynamics problem. The model was applied to seven experienced pole-vaulters. The force and the moment exerted on the pole by the pole-vaulter during the last stride before take off and during jump stage, were calculated. This analysis of the compressive force and bending moment for seven pole-vaulters helps to highlight the impact of the moment in the performance. The conclusion is confirmed by an additional comparative study carried out on two pole-vaulters, with comparable morphologies and performing with the same pole.