RESUMEN
Although dendrimer supports have been known as key parts of nanocatalysts, the capability of rigid dendrimers for this function has not yet been reported. Here, the study is focused on ferrocenylmethylenetriazolyl-terminated dendrimers (FcMTPD) as supports of remarkably efficient nanogold and nanopalladium catalysts. A biphasic system is elaborated to evaluate the catalytic activity of FcMTPD-supported Au and Pd nanoparticles (NPs) for the reduction of 4-nitrophenol to 4-aminophenol by NaBH4 at 20 °C, and FcMTPD-supported PdNPs are found to be the best nanocatalysts with a rate constant kapp = 7.8 × 10-2 s-1. Excellent catalytic results are also obtained in this reaction for FcMTPD-supported AuNPs with a rate constant kapp = 5.6 × 10-2 s-1. For both Pd NPs and AuNPs, the kinetic results are shown to strongly depend on the method of preparation of these NPs that influences the NP size and thus their catalytic efficiency. The FcMTPD-stabilized PdNPs are easily recovered and reused at least 13 times, and their catalytic performance displays only a slight decrease during the first seven runs.
RESUMEN
Production of hydrogen (H2) upon hydrolysis of inorganic hydrides potentially is a key step in green energy production. We find that visible-light irradiation of aqueous solutions of ammonia-borane (AB) or NaBH4 containing "click"-dendrimer-stabilized alloyed nanocatalysts composed of nanogold and another late transition-metal nanoparticle (LTMNP) highly enhances catalytic activity for H2 generation while also inducing alloy to Au core@M shell nanocatalyst restructuration. In terms of visible-light-induced acceleration of H2 production from both AB and NaBH4, the Au1Ru1 alloy catalysts show the most significant light-boosting effect. Au-Rh and Au-PtNPs are also remarkable with total H2 release time from AB and NaBH4 down to 1.3 min at 25 °C (AuRh), 3 times less than in the dark, and Co is the best earth-abundant metal alloyed with nanogold. This boosting effect is explained by the transfer of plasmon-induced hot electron from the Au atoms to the LTMNP atoms facilitating water O-H oxidative addition on the LTMNP surface, as shown by the large primary kinetic isotope effect kH/kD upon using D2O obtained for both AB and NaBH4. The second simultaneous and progressive effect of visible-light irradiation during these reactions, alloy to Au core@M shell restructuration, enhances the catalytic activity in the recycling, because, in the resulting Au core@M shell, the surface metal (such as Ru) is much more active than the original Au-containing alloy surface in dark reactions. There is no light effect on the rate of hydrogen production for the recycled nanocatalyst because of the absence of Au on the NP surface, but it is still very efficient in hydrogen release during four cycles because of the initial light-induced restructuration, although it is slightly less efficient than the original nanoalloy in the presence of light. The dendritic triazole coordination on each LTMNP surface appears to play a key role in these remarkable light-induced processes.
RESUMEN
The development of antifouling coatings with restricted cell and bacteria adherence is fundamental for many biomedical applications. A strategy for the fabrication of antifouling coatings based on the layer-by-layer assembly and thermal annealing is presented. Polyelectrolyte multilayers (PEMs) assembled from chitosan and hyaluronic acid were thermally annealed in an oven at 37°C for 72h. The effect of annealing on the PEM properties and topography was studied by atomic force microscopy, ζ-potential, circular dichroism and contact angle measurements. Cell adherence on PEMs before and after annealing was evaluated by measuring the cell spreading area and aspect ratio for the A549 epithelial, BHK kidney fibroblast, C2C12 myoblast and MC-3T3-E1 osteoblast cell lines. Chitosan/hyaluronic acid PEMs show a low cell adherence that decreases with the thermal annealing, as observed from the reduction in the average cell spreading area and more rounded cell morphology. The adhesion of S. aureus (Gram-positive) and E. coli (Gram-negative) bacteria strains was quantified by optical microscopy, counting the number of colony-forming units and measuring the light scattering of bacteria suspension after detachment from the PEM surface. A 20% decrease in bacteria adhesion was selectively observed in the S. aureus strain after annealing. The changes in mammalian cell and bacteria adhesion correlate with the changes in topography of the chitosan/hyaluronic PEMs from a rough fibrillar 3D structure to a smoother and planar surface after thermal annealing.
