In vitro and in vivo evaluation of Δ9-tetrahidrocannabinol/PLGA nanoparticles for cancer chemotherapy.

Nanoplatforms can optimize the efficacy and safety of chemotherapy, and thus cancer therapy. However, new approaches are encouraged in developing new nanomedicines against malignant cells. In this work, a reproducible methodology is described to prepare Δ(9)-tetrahidrocannabinol (Δ(9)-THC)-loaded poly(d,l-lactide-co-glycolide) (PLGA) nanoparticles against lung cancer. The nanoformulation is further improved by surface functionalization with the biodegradable polymers chitosan and poly(ethylene glycol) (PEG) in order to optimize the biological fate and antitumor effect. Mean nanoparticle size (≈ 290 nm) increased upon coating with PEG, CS, and PEG-CS up to ≈ 590 nm, ≈ 745 nm, and ≈ 790 nm, respectively. Surface electrical charge was controlled by the type of polymeric coating onto the PLGA particles. Drug entrapment efficiencies (≈ 95%) were not affected by any of the polymeric coatings. On the opposite, the characteristic sustained (biphasic) Δ(9)-THC release from the particles can be accelerated or slowed down when using PEG or chitosan, respectively. Blood compatibility studies demonstrated the adequate in vivo safety margin of all of the PLGA-based nanoformulations, while protein adsorption investigations postulated the protective role of PEGylation against opsonization and plasma clearance. Cell viability studies comparing the activity of the nanoformulations against human A-549 and murine LL2 lung adenocarcinoma cells, and human embryo lung fibroblastic MRC-5 cells revealed a statistically significant selective cytotoxic effect toward the lung cancer cell lines. In addition, cytotoxicity assays in A-549 cells demonstrated the more intense anticancer activity of Δ(9)-THC-loaded PEGylated PLGA nanoparticles. These promising results were confirmed by in vivo studies in LL2 lung tumor-bearing immunocompetent C57BL/6 mice.

Functional PLGA NPs for oral drug delivery: recent strategies and developments.

This article presents the potential of PLGA nanoparticles for the oral administration of drugs. Different strategies are used to improve oral absorption of these nanoparticles. These strategies are based on modification of nanoparticle surface properties. They can be achieved either by coating the nanoparticle surface with stabilizing hydrophilic bioadhesive polymers or surfactants, or by incorporating biodegradable copolymers containing a hydrophilic moiety. Some substances such as chitosan, vitamin E, methacrylates, lectins, lecithins, bile salts and RGD molecules are employed for this purpose. Of especial interest are nanoparticles production methods and, in order to improve oral bioavailability, the mechanism of each additive.

Development and validation of an RP-HPLC method for CB13 evaluation in several PLGA nanoparticle systems.

A simple, fast, and reversed-phase high-performance liquid chromatographic (RP-HPLC) method has been developed and validated for determining of a cannabinoid derivate, which displays potent antihyperalgesic activity, 1-naphthalenyl[4-(pentyloxy)-1-naphthalenyl]methanone (CB13) into PLGA nanoparticles. Separation was achieved in a C18 column using a mobile phase consisting of two solvents: solvent A, consisting of acetonitrile : water : acetic acid (75 : 23.7 : 1.3 v/v), and solvent B, consisting of acetonitrile. An isocratic method (70 : 30 v/v), with a flow rate of 1.000 mL/min, and a diode array detector were used. The developed method was precise, accurate, and linear over the concentration range of analysis with a limit of detection and a limit of quantification of 0.5 and 1.25 µg/mL, respectively. The developed method was applied to the analysis of CB13 in nanoparticles samples obtained by three different procedures (SEV, FF, and NPP) in terms of encapsulation efficiency and drug release. Nanoparticles size and size distribution were also evaluated founding that NPP method presented the most lowest particle sizes with narrow-size distribution (≈320 nm) and slightly negative zeta potential (≈-25 mV) which presumes a suitable procedure for the synthesis of PLGA-CB13 nanoparticles for oral administration.

Insulin-loaded PLGA microparticles: flow focusing versus double emulsion/solvent evaporation.

CONTEXT: Oral administration of insulin is severely limited by very low bioavailability. Biocompatible polymeric nanocarriers have been investigated to overcome this problem. Flow focusing (FF) has revolutionized current engineering of poly(D,L-lactide-co-glycolide) (PLGA) based micromedicines. This technique has never been used to formulate insulin-loaded PLGA microparticles. OBJECTIVE: Investigation of the benefits rising from the synthesis of insulin-loaded PLGA microplatforms by FF, compared to double emulsion/solvent evaporation method. MATERIALS AND METHODS: Both synthesis methodologies were compared in terms of geometry, surface physicochemical properties and insulin vehiculization capabilities. The stability of the peptide during the formulation procedure was further analysed. RESULTS: FF permitted the preparation of insulin-loaded microcarriers with better geometry and physicochemical properties for the oral route, along with greater insulin loading capabilities and sustained insulin release kinetics. DISCUSSION AND CONCLUSION: Results have lead to the identification of the best formulation conditions for the engineering of insulin-loaded PLGA microparticles against diabetes.