Microfabrication of Gelatin Methacrylate/Hydroxyapatite Composites by Utilizing Alternate Soaking Process.

To construct a complex three-dimensional (3D) structure mimicking bone microstructure, hydrogel models of polymerized gelatin methacrylate (pGelMA) were fabricated by using stereolithography and modified with hydroxyapatite (HAp) via an alternate soaking process (ASP) using a solution of calcium and phosphate ions. Fabricated pGelMA line models whose widths were designed as 100, 300, and 600 µm were modified with HAp by ASP by changing the immersion time and number of cycles. After ASP, all of the line models with widths of 100, 300, and 600 µm were successfully modified with HAp, and large amounts of HAp were covered with the fabricated models by increasing both the immersion time and the number of cycles in ASP. HAp was observed near the surface of the line model with a width of 600 µm after ASP at an immersion time of 10 s, while the entire model was modified with HAp using ASPs for longer immersion times. The adhesion and spread of mesenchymal stem cells (MSCs) on the pGelMA-HAp discs depended on the ASP conditions. Moreover, the HAp modification of 3D pyramid models without alteration of the microstructure was also conducted. This two-step fabrication method of first fabricating frameworks of hydrogel models by stereolithography and subsequently modifying the fabricated models with HAp will lead to the development of 3D cell culture systems to support bone grafts or to create biological niches, such as artificial bone marrow.

On-Demand Tunability of Microphase Separation Structure of 3D Printing Material by Reversible Addition/Fragmentation Chain Transfer Polymerization.

Controlling the phase-separated structure of polymer alloys is a promising method for tailoring the properties of polymers. However, controlling the morphology of phase-separated structures is challenging. Recently, phase-separated structures have been fabricated via 3D printing; however, only a few methods that enable on-demand control of phase separation have been reported. In this study, laser-scanning stereolithography, a vat photopolymerization method, is used to form a phase-separated structure via polymerization-induced microphase separation by varying the scanning speed and using macro-reversible addition/fragmentation chain transfer (macro-RAFT) agents with different average molar masses, along with multiarmed macro-RAFT agents; such structures were used to fabricate 3D-printed parts. Various phase-separated morphologies including sea-island and reverse sea-island were achieved by controlling the laser scanning speed and RAFT type. Heterogeneous structures with different material properties were also achieved by simply changing the laser scanning speed. As the deformation due to shrinkage in the process of cleaning 3D-printed parts depends on the laser scanning speed, shape correction was introduced to suppress the effect of shrinkage and obtain the desired shape.

Fabrication of Flexible Wiring with Intrinsically Conducting Polymers Using Blue-Laser Microstereolithography.

Recently, flexible devices using intrinsically conductive polymers, particularly poly(3,4-ethylenedioxythiophene) (PEDOT), have been extensively investigated. However, most flexible wiring fabrication methods using PEDOT are limited to two-dimensional (2D) fabrication. In this study, we fabricated three-dimensional (3D) wiring using the highly precise 3D printing method of stereolithography. Although several PEDOT fabrication methods using 3D printing systems have been studied, few have simultaneously achieved both high conductivity and precise accuracy. In this study, we review the post-fabrication process, particularly the doping agent. Consequently, we successfully fabricated wiring with a conductivity of 16 S cm-1. Furthermore, flexible wiring was demonstrated by modeling the fabricated wiring on a polyimide film with surface treatment and creating a three-dimensional fabrication object.

3D-Printed Micro-Tweezers with a Compliant Mechanism Designed Using Topology Optimization.

The development of handling technology for microscopic biological samples such as cells and spheroids has been required for the advancement of regenerative medicine and tissue engineering. In this study, we developed micro-tweezers with a compliant mechanism to manipulate organoids. The proposed method combines high-resolution microstereolithography that uses a blue laser and topology optimization for shape optimization of micro-tweezers. An actuation system was constructed using a linear motor stage with a force control system to operate the micro-tweezers. The deformation of the topology-optimized micro-tweezers was examined analytically and experimentally. The results verified that the displacement of the tweezer tip was proportional to the applied load; furthermore, the displacement was sufficient to grasp biological samples with an approximate diameter of several hundred micrometers. We experimentally demonstrated the manipulation of an organoid with a diameter of approximately 360 µm using the proposed micro-tweezers. Thus, combining microstereolithography and topology optimization to fabricate micro-tweezers can be potentially used in modifying tools capable of handling various biological samples.

Preparation and characterization of an imogolite/chitosan hybrid with pyridoxal-5'-phosphate as an interfacial modifier.

Imogolite/chitosan hybrid films were prepared using pyridoxal-5'-phosphate (PLP) as an interfacial modifier. Thermogravimetric analysis and spectroscopic measurements revealed that the phosphate group of PLP was adsorbed on the imogolite. Furthermore, rheological measurements suggested that the PLP-modified imogolites (PLP-imogolite) had strong interactions with chitosan in solution. Moreover, UV absorption of the hybrid film showed that PLP and chitosan formed Schiff base linkages. Therefore, the hybrid films exhibited a significant improvement in their mechanical properties compared to those of pristine chitosan/imogolite hybrid films.

Preparation of an (inorganic/organic) hybrid hydrogel from a peptide oligomer and a tubular aluminosilicate nanofiber.

'Imogolite', a tubular inorganic nanotube surface, was modified with a peptide oligomer to prepare a hybrid hydrogel. The formation of the gels was confirmed by conducting a vial inversion test and rheological measurements. The surface modification of imogolite with the peptide oligomer was verified by performing thermogravimetric analysis and circular dichroism measurements. Furthermore, the formation of the network-like morphology of the prepared hydrogel was confirmed by scanning force microscopy.

Synthesis and Hydration Behavior of a Hydrolysis-Resistant Quasi-Choline Phosphate Zwitterionic Polymer.

A hydrolysis-resistant polymer bearing new quasi-choline phosphate (quasi-CP) structures as side groups, poly(2-methacryloyloxyethyl choline methylphosphonate) (PMCPm), was designed and synthesized. Radical polymerization and sub-surface-initiated radical polymerization were used to prepare homopolymer and polymer brush on polymer substrates. Hydrolytic stability and hydrophilicity of the polymer were confirmed by nuclear magnetic resonance and contact angle measurements. Furthermore, the hydration states were investigated using Fourier-transform infrared spectroscopy and differential scanning calorimetry. The similar hydration behavior of PMCPm to poly(2-methacryloyloxyethyl phosphorylcholine) (PMPC) sheds light on understanding the interfacial functions of quasi-CP-bearing zwitterionic biomaterials.

Synthesis of a conductive polymer thin film having a choline phosphate side group and its bioadhesive properties.

A conductive polymer thin film having choline phosphate as the side group was prepared. Quartz crystal microbalance (QCM) was employed to evaluate the adsorption of the model protein, bovine serum albumin (BSA), on the films deposited on indium tin oxide (ITO) electrodes. Cell adsorption on the film was evaluated by a fibroblast NIH3T3.

Depth-Resolved Characterization of Perylenediimide Side-Chain Polymer Thin Film Structure Using Grazing-Incidence Wide-Angle X-ray Diffraction with Tender X-rays.

Polymers with a perylenediimide (PDI) side chain (PAc12PDI) consist of two kinds of crystalline structures with various types of orientations in a thin film. Understanding the population of the microcrystalline structure and its orientation along the thickness is strongly desired. Grazing-incidence wide-angle X-ray diffraction (GIWAXD) measurements with hard X-rays, which are generally chosen as λ = 0.1 nm, are a powerful tool to evaluate the molecular aggregation structure in thin films. A depth-resolved analysis for the outermost surface of the polymeric materials using conventional GIWAXD measurements, however, has limitations on depth resolution because the X-ray penetration depth dramatically increases above the critical angle. Meanwhile, tender X-rays (λ = 0.5 nm) have the potential advantage that the penetration depth gradually increases above the critical angle, leading to precise characterization for the population of crystallite distribution along the thickness. The population of the microcrystalline states in the PAc12PDI thin film was precisely characterized utilizing GIWAXD measurements using tender X-rays. The outermost surface of the PAc12PDI thin film is occupied by a monoclinic lattice with a = 2.38 nm, b = 0.74 nm, c = 5.98 nm, and ß = 108.13°, while maintaining the c-axis perpendicular to the substrate surface. Additionally, the presence of solid substrate controls the formation of the crystallite with unidirectional orientation.

Evidence for Surface Recognition by a Cholesterol-Recognition Peptide.

Two cholesterol recognition/interaction amino-acid consensus peptides, N-acetyl-LWYIKC-amide, and N-acetyl-CLWYIK-amide, have been coupled to exchangeable mimics of Chol (cholesterol) and Phos (1,2-dipalmitoyl-sn-glycerol-3-phospho-(1'rac-glycerol)) via disulfide bond formation. Equilibration between Chol and Phos via thiolate-disulfide interchange reactions has revealed that both peptides favor Chol as a nearest-neighbor in liquid-disordered (ld) bilayers to the same extent. In contrast, no Chol- or Phos-recognition could be detected by these peptides in analogous liquid-ordered (lo) bilayers. Fluorescence measurements of the tryptophan moiety have shown that both peptides favor the membrane-water interface. Taken together, these results provide strong evidence that the recognition behavior of the LWYIK motif is, fundamentally, a surface phenomenon but that partial penetration into the bilayer is also necessary.

Exchangeable Mimics of DPPC and DPPG Exhibiting Similar Nearest-Neighbor Interactions in Fluid Bilayers.

The interactions between an exchangeable mimic of 1,2-dipalmitoyl-sn-glycero-3-phosphocholine (DPPC), Phos(±), with an exchangeable mimic of cholesterol, Chol, have been analyzed in fluid bilayers by means of nearest-neighbor recognition measurements. These interactions have been found to be very similar to those of an exchangeable mimic of 1,2-dipalmitoyl-sn-glycerol-3-phospho-(1'rac-glycerol) (DPPG), Phos(-), interacting with Chol. Thus, both phospholipids have a similar preference for becoming nearest-neighbors of Chol in the liquid-ordered (l0) phase, and both mix, ideally, with Chol in the liquid-disordered (ld) phase. These findings, together with the almost negligible screening effects found for the latter, provide strong evidence that electrostatic forces play a minor role in the preference that both phospholipids have in becoming a favored nearest-neighbor of Chol. They also imply that the main driving force for forming the liquid-ordered phase, and for defining the lateral organization of this phase, is an intrinsic affinity that high-melting lipids and cholesterol have for each other.

Peptide Recognition of Cholesterol in Fluid Phospholipid Bilayers.

N-Acetyl-LWYIKC-amide, a cholesterol recognition/interaction amino acid consensus (CRAC) peptide, has been found capable of recognizing an exchangeable form of cholesterol in liquid-disordered (l(d)) bilayers derived from 1,2-dipalmitoyl-sn-glycero-3-phosphocholine (DPPC). In sharp contrast, such recognition is barely detectable in analogous cholesterol-rich, liquid-ordered (l0) bilayers. These findings represent the first evidence for a peptide favoring a sterol as a nearest-neighbor in fluid bilayers. They also reveal that such recognition can be strongly dependent on the degree of compactness of the membrane.

A self-oscillating gel actuator driven by ferroin.

In the wake of the Belousov-Zhabotinsky reaction catalyzed by ferroin, the swelling-deswelling oscillating soft actuator exhibits 7 min period of self-oscillation for the first time.

A hydro/organo/hybrid gelator: a peptide lipid with turning aspartame head groups.

This work presents a novel bola-type peptide lipid which can gelate water, organic solvents, and water/organic-solvent mixtures. In its molecular structure, an amphiphilic dipeptide aspartame (L-α-aspartyl-L-phenylalanine methyl ester) is connected at both ends of an alkylene linker. The different morphologies in the hydrogel (helical nanotapes) and the organogel (tape-like nanostructures) were visualized by energy-filtering transmission electron microscopy (EF-TEM) and energy-filtering scanning electron microscopy (FE-SEM), and the molecular arrangement was examined using X-ray diffraction (XRD), infrared (IR) spectroscopy, and circular dichroism (CD) spectroscopy. Possessing a hydrophilic aspartic acid group and a (relatively) hydrophobic phenylalanine methyl ester group, the dipeptide head group can turn about in response to solvent polarity. As a consequence, the solvent condition changed the molecular packing of the gelator and affected the overall supramolecular structure of the gel. It is noted that the peptide lipid gelated mixed solvents of water and organic solvents such as dichloromethane, liquid-paraffin, olive-oil, silicone-oils, and so on. The present hybrid gel can simultaneously hold hydrophilic and hydrophobic functional materials.

Fusion-triggered switching of enzymatic activity on an artificial cell membrane.

A nanosensory membrane device was constructed for detecting liposome fusion through changes in an enzymatic activity. Inspired by a biological signal transduction system, the device design involved functionalized liposomal membranes prepared by self-assembly of the following molecular components: a synthetic peptide lipid and a phospholipid as matrix membrane components, a Schiff's base of pyridoxal 5'-phosphate with phosphatidylethanolamine as a thermo-responsive artificial receptor, NADH-dependent L-lactate dehydrogenase as a signal amplifier, and Cu(2+) ion as a signal mediator between the receptor and enzyme. The enzymatic activity of the membrane device was adjustable by changing the matrix lipid composition, reflecting the thermotropic phase transition behavior of the lipid membranes, which in turn controlled receptor binding affinity toward the enzyme-inhibiting mediator species. When an effective fusogen anionic polymer was added to these cationic liposomes, membrane fusion occurred, and the functionalized liposomal membranes responded with changes in enzymatic activity, thus serving as an effective nanosensory device for liposome fusion detection.

Intermolecular communication on a liposomal membrane: enzymatic amplification of a photonic signal with a gemini peptide lipid as a membrane-bound artificial receptor.

A supramolecular system that can activate an enzyme through photo-isomerization was constructed by using a liposomal membrane scaffold. The design of the system was inspired by natural signal transduction systems, in which enzymes amplify external signals to control signal transduction pathways. The liposomal membrane, which provided a scaffold for the system, was prepared by self-assembly of a photoresponsive receptor and a cationic synthetic lipid. NADH-dependent L-lactate dehydrogenase, the signal amplifier, was immobilized on the liposomal surface by electrostatic interactions. Recognition of photonic signals by the membrane-bound receptor induced photo-isomerization, which significantly altered the receptor's metal-binding affinity. The response to the photonic signal was transmitted to the enzyme by Cu(2+) ions. The enzyme amplified the chemical information through a catalytic reaction to generate the intended output signal.

Switching of the enzymatic activity synchronized with signal recognition by an artificial DNA receptor on a liposomal membrane.

We constructed a supramolecular system on a liposomal membrane that is capable of activating an enzyme via DNA hybridization. The design of the system was inspired by natural signal transduction systems, in which enzymes amplify external signals to control signal transduction pathways. The liposomal membrane, providing a platform for the system, was prepared by the self-assembly of an oligonucleotide lipid, a phospholipid and a cationic synthetic lipid. The enzyme was immobilized on the liposomal surface through electrostatic interactions. Selective recognition of DNA signals was achieved by hybridizing the DNA signals with the oligonucleotide lipid embedded in the liposome. The hybridized DNA signal was sent to the enzyme by a copper ion acting as a mediator species. The enzyme then amplified the event by the catalytic reaction to generate the output signal. In addition, our system demonstrated potential for the discrimination of single nucleotide polymorphisms.

Photodynamic activity of C70 caged within surface-cross-linked liposomes.

[70]Fullerene (C(70)) encapsulated into a surface-cross-linked liposome, a so-called cerasome, was prepared by an exchange reaction incorporating C(70)gamma-cyclodextrin complexes into lipid membranes. Fullerene exchange in a cerasome-incorporated C(70) (CIC(70)), as well as in a lipid-membrane-incorporated C(70) (LMIC(70)), was completed within 1 min with stirring at 25 degrees C. CIC(70) was more resistant to lysis than LMIC(70) towards lysing agents such as surfactants. Furthermore, the photodynamic activity of CIC(70) in HeLa cells was similar to that of LMIC(70), indicating that C(70) can act as a photosensitizing drug (PS) without release from cerasome membranes. Thus, in contrast with general drug-delivery systems (DDSs), which require the drug to be released from the interior of liposomes, carriers for PSs for use in photodynamic therapy (PDT) do not necessarily need to release the drug. These results indicate that DDSs with high morphological stability can increase the residence time in blood and achieves tumor-selective drug delivery by the enhanced permeability and retention (EPR) effect.

RNAi gene silencing using cerasome as a viral-size siRNA-carrier free from fusion and cross-linking.

Surface-rigidified cerasomes (ceramic-coated liposomes) are neither fused nor cross-linked when bound to siRNA (short duplex RNA) but not to plasmid DNA (long duplex DNA) which induces cross-linking. Non-ceramic reference liposomes are easily fused by the siRNA. The cerasome can thus be used as a viral-size siRNA-carrier in a wide range of concentration for RNAi silencing of exogenous and endogenous genes.