Development of an eco-friendly sample preparation protocol for metal determination in food samples: an oxygen pressurized single reaction chamber using diluted nitric acid.

Many efforts have been recently made to improve the digestion efficiency by using powerful equipment or by using an auxiliary reagent. In this work, an alternative method is reported, which explores a digestion system based on a single reaction chamber (SRC) technology pressurized with O2 for reducing the amount of acid, without impairing the digestion efficiency. Before digestion, the system was pressurized with compressed air (20 bar, 20% O2) while the temperature was evaluated from 180 up to 270 °C. The procedure was also carried out under O2 pressure (20 bar). For each temperature several acid concentrations were evaluated (0.1 to 3 mol L-1 HNO3), being possible to correlate the effectiveness of each acid concentration with temperature. The proposed method was applied to the simultaneous digestion of several organic matrices with variable content of fat, protein, and carbohydrate (whole milk powder, bovine liver, parsley, and linseed). The residual carbon content was lower than 4% (C lower than 200 mg L-1 in digests), showing the high digestion efficiency of the proposed approach. Up to 250 mg of all food matrices were digested using a sub-stoichiometric amount of HNO3 (1 mol L-1 solution), which was only achieved due to the use of O2 as an auxiliary reagent. Barium, Ca, Cu, Fe, K, Mg, Mn, Na, Sr, and Zn were determined by ICP-OES, and the accuracy was better than 95% for standard reference materials of corn bran, whole milk powder, and bovine liver. It is an important feature, being in agreement with green chemistry recommendations because very low amounts of reagents are required for sample digestion, as well as low amounts of residues are generated.

Portable dehumidifiers as an original matrix for the study of inhalable nanoparticles in school.

Good air quality is documented as a significant factor of social justice. The human health hazards associated with air pollution are not distributed equally across cities; the most vulnerable people are more exposed to ambient air as they commute to work and wait for buses or trains at the stations. Aerosols play important roles in atmosphere quality and the climate; their oxidation at the nanoscale level may possibly increase the reactivity and toxicity of atmospheric particulates. Indoor school environments are characterized by high concentrations of different airborne particulate and gaseous pollutants. The documentation of nanoparticles (NPs), ultra-fine particles (UFPs), and micron-size particle species present in indoor primary schools are an important aspect in the recognition of their influence in respirational difficulties and decreased cognitive progress in children. This work utilizes the study of condensed water, sampled with portable dehumidifiers (PD), to describe NPs and UFPs in the vapor stage of enclosed zones. The acquired extracts were analyzed by advanced electron microscopy techniques. A total of 392 NPs and 251 UFPs were examined in a set of 22 samples acquired in moderately limited or inadequately ventilated indoor areas from several schools. Noting that NPs-related disorders happen at particular places of respirational structure, identification of site-specific NPs accumulation should be anticipated in direction to better verify the corresponding human health outcomes resulting from respirable NPs.

An ultrasound-assisted sample preparation method of carbonatite rock for determination of rare earth elements by inductively coupled plasma mass spectrometry.

RATIONALE: A method for the determination of rare earth elements in carbonatite rocks by inductively coupled plasma mass spectrometry (ICP-MS) was developed. METHODS: An alkaline rock, carbonatite, was submitted to ultrasound-assisted extraction (USAE) using an ultrasound bath, a cup horn system or an ultrasound probe. The main USAE parameters were evaluated, such as extraction time (1 to 30 min), extraction temperature (20 to 100°C) and ultrasound amplitude (10 to 100%). For ICP-MS, a desolvation system (APEX-Q) was used to reduce interference in lanthanide determination. To evaluate if the effect of ultrasound improved extraction, experiments were carried out using magnetic stirring (500 rpm) for comparison. RESULTS: The temperature and ultrasound amplitude optimized for the method were 70°C and 40%, respectively, using dilute nitric acid (3% v/v). Quantitative analyte recoveries were obtained using an ultrasound bath (25 kHz/100 W) which allowed for the simultaneous extraction of twelve replicates. CONCLUSIONS: All the results obtained with the use of ultrasound systems were better than those obtained with mechanical stirring. The extracts were suitable for ICP-MS analysis and the results were in agreement with those obtained by the reference method (using wet acid digestion). Based on the results, the use of USAE can be considered an alternative method for sample preparation of carbonatite rocks, under milder conditions, for further ICP-MS analysis.

La2O3 Nanoparticles: Study of Uptake and Distribution in Pfaffia glomerata (Spreng.) Pedersen by LA-ICP-MS and µ-XRF.

The production and use of nanoparticles (NPs) in different fields increased in the last years. However, some NPs have toxicological properties, making these materials potential emerging pollutants. Therefore, it is important to investigate the uptake, transformation, translocation, and deposition of NPs in plants. In this work, laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) and micro X-ray fluorescence (µ-XRF) were used to investigate the uptake and translocation of La2O3 NPs to stem and leaves of Pfaffia glomerata (Spreng.) Pedersen after in vitro cultivation of plants in the presence of 400 mg L-1 of La2O3 NPs. By using LA-ICP-MS and µ-XRF, image of the spatial distribution of La in the leaves was obtained, where higher concentration of La was observed in the main veins. Differences in the signal profile of La in leaves of plants cultivated in the presence of bulk La2O3 (b-La2O3) and La2O3 NPs were observed. Sharp peaks of La indicated that NPs were transported to the stems and leaves of plants treated with La2O3 NPs. Both LA-ICP-MS and µ-XRF techniques have shown to be useful for detecting NPs in plants, but LA-ICP-MS is more sensitive than µ-XRF and allowed better detection and visualization of La distribution in the whole leaf.

A versatile green analytical method for determining chlorine and sulfur in cereals and legumes.

A versatile, rapid and safe green method for chlorine and sulfur determination using ion chromatography in cereals and legumes was developed. Microwave-induced combustion was evaluated for sample preparation. Ultrapure water and alkaline solutions were assessed for absorption of the analytes. Water was selected because good recoveries (97-109%) were obtained for both analytes. Low consumption of reagents and small quantities of waste are two important advantages of the proposed method. Accuracy was evaluated by analysis of a standard reference material, which agreed with certified values (91-101%). The results for repeatability (RSDs ≤ 4%) and intermediate precision (RSDs ≤ 7%) prove the good precision of the proposed method. Limits of quantification were 16 and 17 mg kg-1 for Cl and S, respectively. Concentrations of Cl and S varied across a wide range (Cl: 35-930 mg kg-1; S: 678-5124 mg kg-1) for 34 samples analyzed, which were, for most of the results, close to the values found in the literature.

Rare earth elements profile in a cultivated and non-cultivated soil determined by laser ablation-inductively coupled plasma mass spectrometry.

Rare earth elements (REEs) have several applications but the effects on environment are not well known. Therefore, the aim of this work is to establish a method for direct solid sample analysis by laser ablation-inductively coupled plasma mass spectrometry (LA-ICP-MS) to evaluate the concentration and distribution of REEs in cultivated and non-cultivated soil. Samples were collected in two areas to 40 cm of depth. The LA-ICP-MS method is easy to be implemented and the sample treatment is very fast comprising only its drying, grounding and pressing as a pellet. The accuracy of the method was evaluated by using a certified reference material (BCR 667 - Estuarine Sediment, Institute for Reference Materials and Measurements (IRMM)) where good agreement with the certified values was obtained. Analyte recovery at two levels of concentration (2.5 and 15.0 µg g-1) was also performed and recoveries in the range of 85%-120% were achieved, values that are acceptable for LA-ICP-MS analysis. In general, the concentration of the REEs is higher in the cultivated soil and increased from the surface to deeper layers, which can be a consequence of fertilizer application.

Ultrasound-assisted extraction of rare-earth elements from carbonatite rocks.

In view of the increasing demand for rare-earth elements (REE) in many areas of high technology, alternative methods for the extraction of these elements have been developed. In this work, a process based on the use of ultrasound for the extraction of REE from carbonatite (an igneous rock) is proposed to avoid the use of concentrated reagents, high temperature and excessive extraction time. In this pioneer work for REE extraction from carbonatite rocks in a preliminary investigation, ultrasonic baths, cup horn systems or ultrasound probes operating at different frequencies and power were evaluated. In addition, the power released to the extraction medium and the ultrasound amplitude were also investigated and the temperature and carbonatite mass/volume of extraction solution ratio were optimized to 70°C and 20mg/mL, respectively. Better extraction efficiencies (82%) were obtained employing an ultrasound probe operating at 20kHz for 15min, ultrasound amplitude of 40% (692Wdm-3) and using a diluted extraction solution (3% v/v HNO3+2% v/v HCl). It is important to mention that high extraction efficiency was obtained even using a diluted acid mixture and relatively low temperature in comparison to conventional extraction methods for REE. A comparison of results with those obtained by mechanical stirring (500rpm) using the same conditions (time, temperature and extraction solution) was carried out, showing that the use of ultrasound increased the extraction efficiency up to 35%. Therefore, the proposed ultrasound-assisted procedure can be considered as a suitable alternative for high efficiency extraction of REE from carbonatite rocks.

A new approach to calibration and determination of selected trace elements in food contact polymers by LA-ICP-MS.

A calibration strategy using porous nylon disks and reference solutions is proposed for the first time for matrix matching and determination of As, Ba, Cd, Cr, Pb, Sr and Zn in polymers by laser ablation-inductively coupled plasma mass spectrometry (LA-ICP-MS). Polymer samples commonly used in contact with food were analyzed. The procedure consists on the use of porous nylon disks as support for a dried droplet reference solution. Calibration in the range of 0.50-190µgg-1 for Ba, Cd, Cr, Pb, Sr and Zn and from 0.30-9.0µgg-1 for As was used. Laser and ICP-MS instrument conditions were evaluated in order to achieve the best signal-to-background ratio. The radiofrequency power and carrier gas flow rate were fixed at 1300W and 1.25Lmin-1, respectively. Spot size, repetition rate, scan line speed and laser fluency were set to 100µm, 20Hz, 100µms-1 and 17.9Jcm-2, respectively, as the established conditions for analysis of standards and samples. By using these conditions, limits of detection, estimated considering B+3s (where B is the value of the blank and s is the standard deviation of 10 measurements of the blank), ranged from 0.09µgg-1 (208Pb) to 1.09 (53Cr) and 0.05µgg-1 (208Pb) to 2.10 (53Cr) for calibration with and without 13C as internal standard (IS). In spite to the use of nylon for matrix matching of different polymeric matrices, the normalization with 13C as IS was also evaluated. The precision of the method is relatively good (RSD<20%), and the accuracy of the method, evaluated by analysis of certified reference materials (CRM) and by comparison with results obtained from solution analysis by ICP-MS after sample decomposition by microwave induced combustion (MIC) is relatively good. The suitability of the proposed method resulted in direct and reliable analyses of polymer samples with a simplified or unnecessary sample preparation step. In addition, the calibration with dried droplet reference solutions may be considered a promising procedure in view of its advantages to other forms of calibration, as the use of CRM or the preparation of synthetic standards. The use of porous nylon disks spiked with reference solutions for calibration is the main advantage of the present work.

Simultaneous determination of iron and nickel in fluoropolymers by solid sampling high-resolution continuum source graphite furnace atomic absorption spectrometry.

This paper reports the development of a method of simultaneous determination of iron and nickel in fluoropolymers by high-resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GF AAS) with direct solid sampling. In order to carry out simultaneous measurements, both the main resonance line of nickel (232.003nm) and the adjacent secondary line of iron (232.036nm) were monitored in the same spectral window. The proposed method was optimized with a perfluoroalkoxy (PFA) sample and was applied to the determination of iron and nickel in fluorinated ethylene propylene (FEP) and modified polytetrafluoroethylene (PTFE-TFM) samples. Pyrolysis and atomization temperatures, as well as the use of Pd and H2 (during pyrolysis) as chemical modifiers, were carefully investigated. Compromise temperatures for pyrolysis and atomization of both analytes were achieved at 800 and 2300°C, respectively, using only 0.5Lmin(-1) H2 as chemical modifier during pyrolysis. Calibration curves were performed with aqueous standards by using a single solution which contained both analytes. Limits of detection were 221 and 9.6ngg(-1) for iron and nickel, respectively. Analyte concentrations in all samples ranged from 3.53 to 12.4µgg(-1) for iron and from 37 to 78ngg(-1) for nickel, with relative standard deviation less than 19%. Accuracy was evaluated by comparing these results with those obtained by inductively coupled plasma mass spectrometry after sample digestion by microwave-induced combustion and no significant statistical difference was observed.

Microwave-assisted wet digestion with H2O2 at high temperature and pressure using single reaction chamber for elemental determination in milk powder by ICP-OES and ICP-MS.

In this work a green digestion method which only used H2O2 as an oxidant and high temperature and pressure in the single reaction chamber system (SRC-UltraWave™) was applied for subsequent elemental determination by inductively coupled plasma-based techniques. Milk powder was chosen to demonstrate the feasibility and advantages of the proposed method. Samples masses up to 500mg were efficiently digested, and the determination of Ca, Fe, K, Mg and Na was performed by inductively coupled plasma optical emission spectrometry (ICP-OES), while trace elements (B, Ba, Cd, Cu, Mn, Mo, Pb, Sr and Zn) were determined by inductively coupled plasma mass spectrometry (ICP-MS). Residual carbon (RC) lower than 918mgL(-1) of C was obtained for digests which contributed to minimizing interferences in determination by ICP-OES and ICP-MS. Accuracy was evaluated using certified reference materials NIST 1549 (non-fat milk powder certified reference material) and NIST 8435 (whole milk powder reference material). The results obtained by the proposed method were in agreement with the certified reference values (t-test, 95% confidence level). In addition, no significant difference was observed between results obtained by the proposed method and conventional wet digestion using concentrated HNO3. As digestion was performed without using any kind of acid, the characteristics of final digests were in agreement with green chemistry principles when compared to digests obtained using conventional wet digestion method with concentrated HNO3. Additionally, H2O2 digests were more suitable for subsequent analysis by ICP-based techniques due to of water being the main product of organic matrix oxidation. The proposed method was suitable for quality control of major components and trace elements present in milk powder in consonance with green sample preparation.

Green method by diffuse reflectance infrared spectroscopy and spectral region selection for the quantification of sulphamethoxazole and trimethoprim in pharmaceutical formulations.

An alternative method for the quantification of sulphametoxazole (SMZ) and trimethoprim (TMP) using diffuse reflectance infrared Fourier-transform spectroscopy (DRIFTS) and partial least square regression (PLS) was developed. Interval Partial Least Square (iPLS) and Synergy Partial Least Square (siPLS) were applied to select a spectral range that provided the lowest prediction error in comparison to the full-spectrum model. Fifteen commercial tablet formulations and forty-nine synthetic samples were used. The ranges of concentration considered were 400 to 900 mg g-1SMZ and 80 to 240 mg g-1 TMP. Spectral data were recorded between 600 and 4000 cm-1 with a 4 cm-1 resolution by Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS). The proposed procedure was compared to high performance liquid chromatography (HPLC). The results obtained from the root mean square error of prediction (RMSEP), during the validation of the models for samples of sulphamethoxazole (SMZ) and trimethoprim (TMP) using siPLS, demonstrate that this approach is a valid technique for use in quantitative analysis of pharmaceutical formulations. The selected interval algorithm allowed building regression models with minor errors when compared to the full spectrum PLS model. A RMSEP of 13.03 mg g-1for SMZ and 4.88 mg g-1 for TMP was obtained after the selection the best spectral regions by siPLS.

Characterization of three main degradation products from novel oral anticoagulant rivaroxaban under stress conditions by UPLC-Q-TOF-MS/MS.

Drugs of long-term use may cause the accumulation of chemical compounds in human body. Therefore, the evaluation and structure characterization of synthesis and degradation impurities is substantial to guarantee drug safety and successful pharmaceutical therapy. The present work evaluated the anticoagulant rivaroxabana (RIV) under stress conditions in order to elucidate the chemical structure of major degradation products (DPs) formed after drug exposition to acid and alkaline hydrolysis, and UVC radiation. Analyses were performed in UPLC coupled to quadrupole time-of-flight MS. ESI was applied in positive mode, and C18 Agilent(®) column (2.1×50 mm, 1.8 µm) used for separation of compounds. RIV molecular íon [M+H](+) (m/z 436.07) was fragmented under 20 kV, best energetic condition to obtain clear and reproducible fragmentation pattern, assisting identification of RIV DPs. With support from UPLC separation and specific detection by MS/MS, three main degradation products (DP-1, DP-2, and DP-3) formed under stress conditions were successfully characterized. Presented study agrees with requirements for analytical assessment of impurities in pharmaceutical formulations, ensuring quality of pharmaceutical substances.

Study and determination of elemental impurities by ICP-MS in active pharmaceutical ingredients using single reaction chamber digestion in compliance with USP requirements.

In this work a method for active pharmaceutical ingredients (APIs) digestion using the single reaction chamber (SRC-UltraWave™) system was proposed following the new recommendations of United States Pharmacopeia (USP). Levodope (LEVO), primaquine diphosphate (PRIM), propranolol hydrochloride (PROP) and sulfamethoxazole (SULF) were used to evaluate the digestion efficiency of the proposed method. A comparison of digestion efficiency was performed by measuring the carbon content and residual acidity in digests obtained using SRC and in digests obtained using conventional microwave-assisted digestion system (Multiwave(TM)). Three digestion solutions (concentrated HNO3, aqua regia or inverse aqua regia) were evaluated for digestion of APIs. The determination of Cd, Ir, Mn, Mo, Ni, Os, Pb, Pd, Pt, Rh, Ru was performed using inductively coupled plasma mass spectrometry (ICP-MS) in standard mode. Dynamic reaction cell (DRC) mode was used for the determination of (51)V, (52)Cr, (53)Cr, (63)Cu and (65)Cu in order to solve polyatomic ion interferences. Arsenic and Hg were determined using chemical vapor generation coupled to ICP-MS (FI-CVG-ICP-MS). Masses of 500mg of APIs were efficiently digested in a SRC-UltraWave™ system using only HNO3 and allowing a carbon content lower than 250mg L(-1) in final digests. Inverse aqua regia was suitable for digestion of sample masses up to 250mg allowing the determination of Ir, Pd, Pt, Rh and Ru. By using HNO3 or inverse aqua regia, suitable recoveries were obtained (between 91 and 109%) for all analytes (exception for Os). Limits of quantification were in agreement with USP requirements and they ranged from 0.001 to 0.015µg g(-1) for all elemental impurities (exception for Os). The proposed method was suitable for elemental impurities determination in APIs and it can be used in routine analysis for quality control in pharmaceutical industries.

Feasibility of microwave-induced combustion for trace element determination in Engraulis anchoita by ICP-MS.

A method based on microwave-induced combustion (MIC) was developed for fish (Engraulis anchoita) digestion and subsequent determination of As, Cd, Co, Cr, Cu, Fe, Mn, Mo, Ni, Se, and Zn by inductively coupled plasma mass spectrometry (ICP-MS). A reflux step (5 min) was applied to improve absorption and recovery of analytes. Nitric acid was investigated as absorbing solution and suitable results were achieved using 5 mol L⁻¹ HNO3. Microwave-assisted digestion in closed vessels using concentrated HNO3 was also evaluated for comparison of results. Both sample preparation methods were considered suitable for sample digestion but MIC was preferable not only because diluted HNO3 can be used as absorbing solution but also because it provides higher efficiency of digestion and also better limits of detection. Accuracy was evaluated by the analysis of certified reference materials (DORM-2 and TORT-2) after MIC digestion with subsequent determination by ICP-MS. Agreement with certified values was better than 94%.

Analytical methods for the determination of halogens in bioanalytical sciences: a review.

Fluorine, chlorine, bromine, and iodine have been studied in biological samples and other related matrices owing to the need to understand the biochemical effects in living organisms. In this review, the works published in last 20 years are covered, and the main topics related to sample preparation methods and analytical techniques commonly used for fluorine, chlorine, bromine, and iodine determination in biological samples, food, drugs, and plants used as food or with medical applications are discussed. The commonest sample preparation methods, as extraction and decomposition using combustion and pyrohydrolysis, are reviewed, as well as spectrometric and electroanalytical techniques, spectrophotometry, total reflection X-ray fluorescence, neutron activation analysis, and separation systems using chromatography and electrophoresis. On this aspect, the main analytical challenges and drawbacks are highlighted. A discussion related to the availability of certified reference materials for evaluation of accuracy is also included, as well as a discussion of the official methods used as references for the determination of halogens in the samples covered in this review.

Determination of trace elements in fluoropolymers after microwave-induced combustion.

An effective approach to the digestion of fluoropolymers for the determination of Ag, Ca, Cd, Co, Cr, Cu, Fe, K, Mg, Mn, and Ni impurities has been developed using microwave-induced combustion (MIC) in closed quartz vessels pressurized with oxygen. Samples that were examined included the following: polytetrafluorethylene (PTFE); polytetrafluoroethylene with an additional modifier, perfluoropropylvinylether (PTFE-TFM); and fluorinated ethylene propylene (FEP). A quartz device was used as a sample holder, and the influence of the absorber solution was evaluated. Determination of trace elements was performed by inductively coupled plasma-optical emission and mass spectrometry. Neutron activation analysis (NAA) was used for validation purposes. Results were also compared to those obtained using microwave-assisted acid extraction in high-pressure closed systems. Dilute nitric acid (5 mol L(-1)), which was selected as the absorbing medium, was used to reflux the sample for 5 min after the combustion. Using these conditions, agreement for all analytes was better than 98% when compared to values determined by NAA. The residual carbon content in the digests was lower than 1%, illustrating the high efficiency of the method. Up to 8 samples could be digested within 30 min using MIC, providing a suitable throughput, taking into account the inertness of such samples.

Determination of toxic elements in coal by ICP-MS after digestion using microwave-induced combustion.

A microwave-induced combustion (MIC) procedure was applied for coal digestion for subsequent determination of As, Cd and Pb by inductively coupled plasma mass spectrometry (ICP-MS) and Hg using cold vapor (CV) generation coupled to ICP-MS. Pellets of coal (500 mg) were combusted using 20 bar of oxygen and ammonium nitrate as aid for ignition. The use of nitric acid as absorbing solution (1.7, 3.5, 5.0, 7.0 and 14 mol L(-1)) was evaluated. For coal samples with higher ash content, better results were found using 7.0 mol L(-1) HNO(3) and an additional reflux step of 5 min after combustion step. For coal samples with ash content lower than 8%, 5.0 mol L(-1) nitric acid was suitable to the absorption of all analytes. Accuracy was evaluated using certified reference material (CRM) of coal and spikes. Agreement with certified values and recoveries was better than 95 and 97%, respectively, for all the analytes. For comparison of results, a procedure recommended by the American Society of Testing and Materials (ASTM) was used. Additionally, a conventional microwave-assisted digestion (MAD) in pressurized vessels was also performed. Using ASTM procedure, analyte losses were observed and a relatively long time was necessary for digestion (>6h). By comparison with MAD procedure, higher sample mass can be digested using MIC allowing better limits of detection. Additionally, the use of concentrated acids was not necessary that is an important aspect in order to obtain low blank levels and lower limits of detection, respectively. The residual carbon content in digests obtained by MAD and MIC was about 15% and <1%, respectively, showing the better digestion efficiency of MIC procedure. Using MIC it was possible to digest completely and simultaneously up to eight samples in only 25 min with relatively lower generation of laboratory effluents.

Simultaneous determination of sulphamethoxazole and trimethoprim in powder mixtures by attenuated total reflection-Fourier transform infrared and multivariate calibration.

A partial least-squares calibration (PLS) procedure in combination with infrared spectroscopy has been developed for simultaneous determination of sulphamethoxazole (SMZ) and trimethoprim (TMP) in raw material powder mixtures used for manufacturing commercial pharmaceutical products. Multivariate calibration modeling procedures, interval partial least squares (iPLS) and synergy partial least squares (siPLS), were applied to select a spectral range that provided the lowest prediction error in comparison to the full-spectrum model. The experimental matrix was constructed using 49 synthetic samples and 15 commercial samples. The considered concentration ranges were 400-900 mg g(-1) SMZ and 80-240 mg g(-1) TMP. Spectral data were recorded between 650 and 4000 cm(-1) with a 4 cm(-1) resolution by Fourier transform infrared spectroscopy coupled with attenuated total reflectance (ATR-FTIR) accessory. The proposed procedure was compared with conventional procedure by high performance liquid chromatography (HPLC) using 15 commercial samples containing SMZ and TMP. The results showed that PLS regression model combined to ATR-FTIR is a relatively simple, rapid and accurate procedure that could be applied to the simultaneous determination of SMZ and TMP in routine quality control of powder mixtures. A root mean square error of prediction (RMSEP) of 13.18 mg g(-1) for SMZ and 6.03 mg g(-1) for TMP was obtained after selection of better intervals by siPLS. Using the proposed procedure it is possible to analyze each sample in less than 3 min considering two replicates (excluding the grinding step). Accuracy was checked by comparison to HPLC method and agreement better than 98.8% was achieved.

Sr and Fe relationship with hormone replacement therapy and bone mineral density.

BACKGROUND: We determined blood strontium (Sr) and iron (Fe) concentrations and their relationship with bone mineral density (BMD) and some biochemical parameters in premenopausal and postmenopausal women without or with hormone replacement therapy (HRT). METHODS: Blood Sr and Fe concentrations, BMD, follicle stimulating hormone (FSH), 17beta-estradiol (E2), creatinine, albumin, blood calcium and alkaline phosphatase activity were determined in premenopausal and postmenopausal women without or with HRT (mean ages: 47, 59, and 57 y, respectively). RESULTS: Blood Sr (microg/l) and Fe (mg/l) concentrations in premenopausal (31.65+/-2.96 and 496.05+/-14.37) and postmenopausal women without (28.85+/-2.48 and 525.27+/-8.56) or with (25.98+/-2.73 and 535.77+/-17.57) HRT were not significantly different. BMD L1-L4 and BMD femur (g/cm2) were significantly higher in premenopausal women (1.05+/-0.02 and 0.84+/-0.02) when compared both to postmenopausal women without (0.90+/-0.03 and 0.75+/-0.02) and with (0.93+/-0.03 and 0.73+/-0.01) HRT. However, BMD had no relationship with blood metal concentrations. E2 concentrations were lower in postmenopausal women without HRT, while FSH concentrations were higher in both postmenopausal groups (p<0.05). CONCLUSIONS: Physiological whole blood Sr and Fe concentrations had no significant effect in BMD and other biochemical parameters in pre and postmenopausal women. However, BMD was negatively influenced by FSH concentrations and associated with age.