Controlling the Carbon-Bio Interface via Glycan Functional Adlayers for Applications in Microbial Fuel Cell Bioanodes.

Surface modification of electrodes with glycans was investigated as a strategy for modulating the development of electrocatalytic biofilms for microbial fuel cell applications. Covalent attachment of phenyl-mannoside and phenyl-lactoside adlayers on graphite rod electrodes was achieved via electrochemically assisted grafting of aryldiazonium cations from solution. To test the effects of the specific bio-functionalities, modified and unmodified graphite rods were used as anodes in two-chamber microbial fuel cell devices. Devices were set up with wastewater as inoculum and acetate as nutrient and their performance, in terms of output potential (open circuit and 1 kΩ load) and peak power output, was monitored over two months. The presence of glycans was found to lead to significant differences in startup times and peak power outputs. Lactosides were found to inhibit the development of biofilms when compared to bare graphite. Mannosides were found, instead, to promote exoelectrogenic biofilm adhesion and anode colonization, a finding that is supported by quartz crystal microbalance experiments in inoculum media. These differences were observed despite both adlayers possessing thickness in the nm range and similar hydrophilic character. This suggests that specific glycan-mediated bioaffinity interactions can be leveraged to direct the development of biotic electrocatalysts in bioelectrochemical systems and microbial fuel cell devices.

Tailored glycosylated anode surfaces: Addressing the exoelectrogen bacterial community via functional layers for microbial fuel cell applications.

Grafting of aryldiazonium cations bearing a p-mannoside functionality over microbial fuel cell (MFC) anode materials was performed to investigate the ability of aryl-glycoside layers to regulate colonisation by biocatalytic biofilms. Covalent attachment was achieved via spontaneous reactions and via electrochemically-assisted grafting using potential step experiments. The effect of different functionalisation protocols on MFC performance is discussed in terms of changes in wettability, roughness and electrochemical response of modified electrodes. Water contact angle measurements (WCA) show that aryl-mannoside grafting yields a significant increase in hydrophilic character. Surface roughness determinations via atomic force microscopy (AFM) suggest a more disordered glycan adlayer when electrografting is used to facilitate chemisorption. MFCs were used as living sensors to successfully test the coated electrodes: the response of the MFCs in terms of start-up time was accelerated when compared to that of MFC equipped with non-modified electrodes, this suggests a faster development of a mature biofilm community resulting from aryldiazonium modifications, as confirmed by cyclic voltammetry of MFC anodes. These results therefore indicate that modification with glycans offers a bioinspired route to accelerating biofilm colonisation without any adverse effects on final MFC outputs.

Spontaneous Aryldiazonium Grafting for the Preparation of Functional Cyclodextrin-Modified Materials.

A mild and efficient surface modification protocol for the preparation of ß-cyclodextrin (ßCD) modified surfaces through aryldiazonium-mediated grafting is reported. Monosubstituted 6-O-aminophenol-ß-cyclodextrin (amßCD) was synthesized through a three-step protocol. This compound was found to form supramolecular aggregates in aqueous solutions at relatively low concentrations via cavity-directed self-assembly. Disruption of these supramolecular structures through judicious choice of solvent was found to be essential for the formation of the reactive aryldiazonium species from the amino-phenolic precursor and for spontaneous surface grafting from aqueous solutions. Cyclodextrin thin films were prepared on carbon macroscopic substrates and electrodes and were characterized via infrared reflectance absorption spectroscopy (IRRAS), cyclic voltammetry, and water contact angle measurements. Protein adsorption studies demonstrated that ßCD adlayers reduced nonspecific protein adsorption. ßCD moieties in adlayers can be used nonetheless for specific host-guest complexation and are grafted at the surface with monolayer coverage (1.2 × 10-10 mol cm-2) as demonstrated via experiments using ferrocene, a redox probe. Finally, cyclodextrin covalent immobilization was demonstrated also on stainless steel and polyamide samples, two substrates with wide ranging technological applications.

Antibacterial properties of F-doped ZnO visible light photocatalyst.

Nanocrystalline ZnO photocatalysts were prepared by a sol-gel method and modified with fluorine to improve their photocatalytic anti-bacterial activity in visible light. Pathogenic bacteria such as Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) were employed to evaluate the antimicrobial properties of synthesized materials. The interaction with biological systems was assessed by analysis of the antibacterial properties of bacteria suspended in 2% (w/w) powder solutions. The F-doping was found to be effective against S. aureus (99.99% antibacterial activity) and E. coli (99.87% antibacterial activity) when irradiated with visible light. Production of reactive oxygen species is one of the major factors that negatively impact bacterial growth. In addition, the nanosize of the ZnO particles can also be toxic to microorganisms. The small size and high surface-to-volume ratio of the ZnO nanoparticles are believed to play a role in enhancing antimicrobial activity.