RESUMEN
The impression materials utilized today in dental medicine offer a good reproducibility and are easily accepted by patients. However, because they are polymer-based, they have issues regarding their dimensional stability. In this respect, the present work proposes a new type of dental impression, which is reinforced with rigid mouthguards. The aim of the study is to test the performances of such new impressions by comparing them to conventional ones-from this critical point of view, of the dimensional stability. Three types of polymeric materials were considered for both types of impressions: alginate, condensation silicone, and addition silicone. In order to obtain the new type of impressions, a manufacturing technique was developed, comprising the following phases: (i) conventional impressions were made; (ii) a plaster model was duplicated, and 15 rigid mouthguards were obtained; (iii) they were inserted in the impression technique, with each mouthguard positioned on the cast before the high-consistency material was inserted in the tray and the practitioner took the impression; (iv) the mouthguard remained in the tray and the low-viscosity material was inserted over the mouthguard; (v) the impression was positioned on the model, and after the material hardened, the mouthguard-reinforced impression was analyzed. In the evaluation of the dimensional stability, rigorous statistical analysis was essential to discern the performance differences between conventional and mouthguard-reinforced dental impressions. Statistical analyses employed non-parametric Mann-Whitney U tests because of the non-normal distribution of the data. They indicated a statistically significant improvement in the dimensional stability of addition silicone impressions when reinforced with mouthguards (p < 0.05), showcasing superior performance over conventional methods. Conversely, alginate and condensation silicone reinforced impressions did not exhibit the same level of stability improvement, suggesting the need for further optimization of these materials. In conclusion, from the three considered elastomers, addition silicone was found to be the prime candidate for high-precision dental impressions, with the potential to improve their quality from conventional impressions by utilizing the proposed reinforcing technique.
RESUMEN
Periapical odontogenic granulomas are among the most encountered pathology that involve the alveolar bone, with severe consequences such as bone resorption, the presence of inflammatory infiltrate and the formation of abnormal vascularization. The present study aimed to quantify the existence of the microvessel density (MVD), mast cell density (MCD) and heterogeneity of the encountered blood vessels. A total of 37 patients diagnosed with odontogenic periapical granulomas were included, and the gender distribution, age and localization of the pathological lesions was assessed. After the surgical removal of the periapical odontogenic granuloma, the collected tissue was fixed in 10% buffered formalin. Primary processing, morphological analysis and immunohistochemical staining was performed in order to characterize the altered tissue. The results outlined the presence of a high number of mast cells, especially in the area of the inflamed tissue; the high heterogeneity of the blood vessels; and increased MVD with positive CD34. The conclusions of the study focus on the key role of the mast cells and their implication in the initiation and development of the angiogenesis process, triggering the inflammatory response of the host. Nevertheless, periapical odontogenic granulomas develop as an inflammatory response to the interaction between the host's immune system and microbial invasion.
RESUMEN
Mesenchymal stem cells currently play an important role in the tissue engineering field in developing new regenerative approaches. The oral cavity is a rich source of mesenchymal stem cells, and introducing the use of dental stem cells, characterized by a multilineage differentiation potential, immunomodulatory activity and repair capacity, offers a good perspective for clinical dentistry. Human periapical cyst mesenchymal stem cells (hPCy-MSCs) represent a new category of dental stem cells, being collected from pathological tissue and exhibiting MSCs-like properties. As studies have described, these new identified cells possess the same characteristics as those described in MSCs, exhibiting plasticity, a high proliferation rate and the potential to differentiate into osteogenic, adipogenic and neural lineages. Reusing the biological tissue that is considered pathologic offers a new perspective for the development of further clinical applications. The identification and characterization of MSCs in the human periapical cysts allows for a better understanding of the molecular interactions, the potential healing capacity and the mechanisms of inducing the local osteogenic process, integrated in the microenvironment. Although their involvement in regenerative medicine research is recent, they exhibit important properties that refer them for the development of clinical applications in dentistry.
RESUMEN
Three ceramic and composite computer-aided design/computer-aided manufacturing (CAD/CAM) materials from different manufacturers (Cerasmart (CS)-nanoceramic resin; Straumann Nice (SN)-glass ceramic and Tetric CAD (TC)-composite resin) were tested to investigate the biocompatibility and sustainability on human fibroblasts and keratinocytes cells. Each type of CAD/CAM blocks restorative materials with fine and rough surfaces was exposed to an acidic environment for one month. After that, various powders were obtained by milling. In parallel, powders were also prepared from each restorative material, which were not exposed to the acidic environment. The cytotoxic effects were investigated by means of MTT and LDH assays, as well as nitric oxide production on two human normal cell lines, namely, fibroblasts (BJ) and keratinocytes (HaCaT). In addition, the degree of adhesion of fibroblast cells to each CAD/CAM material was evaluated by scanning electron microscopy (SEM). The results showed that the two samples that were exposed to an acidic environment (CS and SN) induced a reduction of mitochondrial activity and plasma membrane damage as regards the fibroblast cells. A similar effect was observed in TC_fine-exposed material, which seemed to induce necrosis at the tested concentration of 1 mg/mL. No oxidative stress was observed in fibroblasts and keratinocytes treated with the CAD/CAM materials. Regarding the adhesion degree, it was found that the fibroblasts adhere to all the occlusal veneers tested, with the mention that the CS and SN materials have a weaker adhesion with fewer cytoplasmic extensions than TC material. With all of this considered, the CAD/CAM restorative materials tested are biocompatible and represent support for the attachment and dispersion of cells.
Asunto(s)
Diseño Asistido por Computadora , Humanos , Ensayo de Materiales , Propiedades de Superficie , Microscopía Electrónica de RastreoRESUMEN
Fast, economic, and noninvasive, molecular analysis of saliva has the potential to become a diagnostic tool of reference for several local and systemic diseases, oral cancer included. The diagnosis of Oral Squamous Cell Carcinoma (OSCC) can be performed using high specificity and sensibility biomarkers that can be encountered in the biological fluids. Recent advances in salivary proteomics have underlined the potential use of salivary biomarkers as early diagnosis screening tools for oral neoplasia. In this respect, over 100 salivary molecules have been described and proposed as oral cancer biomarkers, out of which cytokines are among the most promising. Besides being directly involved in inflammation and immune response, the role of salivary cytokines in tumor growth and progression linked them to the incidence of oral malignant lesions. This review summarizes the existing studies based on the use of salivary cytokines as potential oral cancer biomarkers, their involvement in the malignant process based on their type, and ther influence upon prognostic and metastatic rates.
RESUMEN
BACKGROUND: Posture is influenced by many factors and dental occlusion seems to have its role on postural stabilization. Our rationale to perform the study was to find out if there are differences of static plantar pressure and stabilometric parameters depending on different dental conditions. METHODS: The observational study consisted in plantar pressure assessment and stabilometric analysis of 95 right-handed healthy volunteer subjects (mean age 22.94 ± 2.52 years) by using the PoData system. Each subject followed four measurements with open eyes: mandibular postural position, maximum intercuspation, biting on cotton rolls and maximum mouth opening. Plantar pressure was recorded on 1st and 5th metatarsal heads and heel, and was expressed as percentage of weight distribution on each foot. The recorded centre of pressure (CoP) parameters were: CoP path length, 90%confidence ellipse area and maximum CoP speed. Statistical analysis used repeated-measures ANOVA with Bonferroni posthoc analysis and Friedman test. RESULTS: Loading on the left 5th metatarsal head was significantly higher in maximum mouth opening condition when compared to maximum intercuspation and to biting on cotton rolls. The left heel loading was significantly lower in the maximum mouth opening in comparison to maximum intercuspation. The CoP path length and maximum CoP speed were significantly higher in maximum mouth opening compared to the other three conditions. Confidence ellipse area had significantly lower values in maximum intercuspation and in the biting on cotton rolls conditions compared to the mandibular postural position, and in maximum intercuspation compared to maximum mouth opening. CONCLUSION: In young adults with an optimum functional occlusion the static plantar pressure is influenced by the maximum mouth opening. An improved postural stability was recorded in maximum intercuspation (a condition used during swallowing) in comparison to mandibular postural position (a condition that allows relaxation of the masticatory muscles after functional moments).