Electropolymerization of Preferred-Oriented Conjugated Microporous Polymer Films for Enhanced Fluorescent Sensing.

High-quality conjugated microporous polymer (CMP) films with orientation and controlled structure are extremely desired for applications. Here, we report the effective construction of CMP 3D composite films (pZn/PTPCz) with a controlled porosity structure and preferred orientation using the template-assisted electropolymerization (EP) approach for the first time. The structure of pZn/PTPCz composite thin films and nitrophenol sensing performance were thoroughly studied. When compared to the control CMP film made on flat indium tin oxide (ITO) substrates, the as-prepared pZn/PTPCz composite films showed significantly enhanced fluorescent intensity and much better sensing performance for the model explosive. This was attributed to the metal-enhanced fluorescence (MEF) of porous nanostructured zinc (pZn) and the additional macroporosity of the pZn/PTPCz composite films. This work provides a feasible approach for creating oriented 3D CMP-based thin films for advanced applications.

Air-Stable Self-Driven UV Photodetectors on Controllable Lead-Free CsCu2I3 Microwire Arrays.

The rapid evolution of the Internet of Things has engendered increased requirements for low-cost, self-powered UV photodetectors. Herein, high-performance self-driven UV photodetectors are fabricated by designing asymmetric metal-semiconductor-metal structures on the high-quality large-area CsCu2I3 microwire arrays. The asymmetrical depletion region doubles the photocurrent and response speed compared to the symmetric structure device, leading to a high responsivity of 233 mA/W to 355 nm radiation. Notably, at 0 V bias, the asymmetric device produces an open-circuit voltage of 356 mV and drives to a short-circuit current of 372 pA; meanwhile, the switch ratio (Iph/Idark) reaches up to 103, indicating its excellent potential for detecting weak light. Furthermore, the device maintains stable responses throughout 10000 UV-light switch cycles, with negligible degradation even after 90-day storage in air. Our work establishes that CsCu2I3 is a good candidate for self-powered UV detection and thoroughly demonstrates its potential as a passive device.

Electronic and magnetic properties of layered M3Si2Te6(M = alkaline earth and transition metals).

Recently, a new layered material, Mn3Si2Te6, was identified to be a semiconductor with nodal-line topological property and ferrimagnetic ground state. In this work, we propose a series of structures, M3Si2Te6(M = alkaline earth and transition metals), and systematically investigate their mechanical, magnetic and electronic properties, and the strain effect to enrich the family of the layered materials for practical applications. We find 13 stable M3Si2Te6, including 5 semiconductors (M = Ca, Sr, Fe, Ru and Os) and 8 metals (M = Sc, Ti, Nb, Ta, Cr, Mo, W and Tc). Two structures (M = Ti and Cr) are antiferromagnetic (AFM), while other structures are non-magnetic (NM). Similar to Mn3Si2Te6, the AFM structures exhibit magnetic anisotropy energies (MAEs) and semiconductors have anisotropic electron effective masses. We further show that compressions along thez-axis can effectively tune the electronic and magnetic properties, such as the semiconductor-metal and NM-AFM transition in Fe3Si2Te6, the two-fold degeneracy of the valence band maximums in Sr3Si2Te6, as well as the reduced MAE for all magnetic structures. These results demonstrate the diverse properties of the layered M3Si2Te6family and provide promising theoretical predictions for the future design of new layered materials.

Physical properties and structural characteristics of particulate matter emitted from a diesel engine fueled with biodiesel blends.

This research explores the influence of renewable fuels, including three kinds of biodiesel along with ethanol on the physical properties and structural characteristics of particulate matter (PM) emitted from a diesel engine in comparison with pure diesel. After adding 10 vol% of grape seed biodiesel, coffee biodiesel and eucalyptus oil into diesel, three biodiesel blended fuels (10% grape seed biodiesel (DGs10), 10% spent coffee ground biodiesel (DC10) and eucalyptus oil biodiesel (DEu10)) were produced and tested in this study. Besides, one ethanol blend containing 9 vol% of ethanol and 1 vol% of biodiesel (blend stabilizer) was also tested to do the comparison. In the present study, scanning transmission electron microscope (STEM) and scanning electron microscope (SEM) were employed for analyzing the microstructure, nanostructure and electron diffraction pattern of PM. Raman spectrometer (RS) was also used for the analysis of structural characterization of PM. In addition, several experimental instruments like microbalance, measuring cup, viscometer, oxygen bomb calorimeter and Gas Chromatography-Mass Spectrometer (GC-MS) were employed to detect the fuel properties, including density, heating value, viscosity, composition and cetane number. A conclusion can be drawn that both biodiesel blends and ethanol blend have a changing effect on the PM properties compared to pure diesel, where biodiesel blends have a slightly weaker influence than ethanol blend. Regarding the biodiesel blends, DGs10 has more impact than DC10 and DEu10 in changes of PM properties, particularly in the reduction of PM mass, making it a good candidate for renewable fuel for diesel engines.

Photosensitive Dielectric 2D Perovskite Based Photodetector for Dual Wavelength Demultiplexing.

Stacked 2D perovskites provide more possibilities for next generation photodetector with more new features. Compared with its excellent optoelectronic properties, the good dielectric performance of metal halide perovskite rarely comes into notice. Here, a bifunctional perovskite based photovoltaic detector capable of two wavelength demultiplexing is demonstrated. In the Black Phosphorus/Perovskite/MoS2 structured photodetector, the comprehensive utilization of the photosensitive and dielectric properties of 2D perovskite allows the device to work in different modes. The device shows normal continuous photoresponse under 405 nm, while it shows a transient spike response to visible light with longer wavelengths. The linear dynamic range, rise/decay time, and self-powered responsivity under 405 nm can reach 100, 38 µs/50 µs, and 17.7 mA W-1 , respectively. It is demonstrated that the transient spike photocurrent with long wavelength exposure is related to the illumination intensity and can coexist with normal photoresponse. Two waveband-dependent signals can be identified and used to reflect more information simultaneously. This work provides a new strategy for multispectral detection and demultiplexing, which can be used to improve data transfer rates and encrypted communications. This work mode can inspire more multispectral photodetectors with different stacked 2D materials, especially to the optoelectronic application of the wide bandgap, high dielectric photosensitive materials.

Ultraviolet photodetector based on RbCu2I3microwire.

Copper-based halide perovskites have shown great potential in lighting and photodetection due to their excellent photoelectric properties, good stability and lead-free nature. However, as an important piece of copper-based perovskites, the synthesis and application of RbCu2I3have never been reported. Here, we demonstrate the synthesis of high-quality RbCu2I3microwires (MWs) by a fast-cooling hot saturated solution method. The prepared MWs exhibit an orthorhombic structure with a smooth surface. Optical measurements show the RbCu2I3MWs have a sharp ultraviolet absorption edge with 3.63 eV optical band gap and ultra-large stokes shift (300 nm) in photoluminescence. The subsequent photodetector based on a single RbCu2I3MW shows excellent ultraviolet detection performance. Under the 340 nm illumination, the device shows a specific detectivity of 5.0 × 109Jones and a responsivity of 380 mA·W-1. The synthesis method and physical properties of RbCu2I3could be a guide to the future optoelectronic application of the new material.

Tunable interstitial anionic electrons in layered MXenes.

Electrides with spatial electrons serving as 'anions' in the cavities or channels exhibit intriguing properties which can be applied in electron injection/emission and high-speed devices. Here, we report a new group of layered electrides, M2X (M = Ti, V, and Cr; X = C and N) with electrons distributed in the interlayer spacings. We find that the interstitial electrons tend to be delocalized from the Ti-based structures to the Cr-based ones. We show that the interstitial electrons originate from thed-electrons of transition metal atoms. Our findings prove the existence of tunable interstitial electrons with rich electronic properties in layered MXenes and provide valuable insights into the design and fabrication of new materials with multiple applications.

Enhanced Optoelectronic Performance Induced by Ion Migration in Lead-Free CsCu2I3 Single-Crystal Microrods.

Lead-free perovskite has attracted great attention in realizing high-performance optoelectronic devices due to their excellent atmospheric stability and nontoxic characteristics. Although a pronounced ion migration effect has been observed in this new class of materials, its potential in enhancing the overall device performance is yet to be fully explored. In this work, we studied the effect of ion migrations on the carrier transport behavior and found that the recoverable migration process can contribute to enhancing the on/off ratio in a lead-free CsCu2I3 single-crystal microrod-based photodetector. In detail, we synthesized CsCu2I3 single-crystal microrods via an in-plane self-assembly supersaturated crystallization approach. These microrods with well-defined morphologies were then used to construct ultraviolet (UV)-band photodetectors, which outperform most reported lead-free perovskite photodetectors based on individual single crystals. Simultaneously, ion migration can result in asymmetric band bending in the two-terminal device, as confirmed by surface potential profiling with Kelvin probe force microscopy (KPFM). Such an effect can be harnessed to increase the on/off ratio by almost an order of magnitude. Furthermore, the lead-free CsCu2I3 single crystal exhibits excellent thermal and air stabilities. These findings demonstrate that the CsCu2I3 single-crystal microrods can be used in stable and efficient photodetection, and the ion migration effect can potentially be utilized for improving the optoelectronic performance of lead-free devices.

Extraordinarily Stable Aqueous Electrochromic Battery Based on Li4Ti5O12 and Hybrid Al3+/Zn2+ Electrolyte.

Aqueous electrochromic battery (ECB) is a multifunctional technology that shows great potential in various applications including energy-saving buildings and wearable batteries with visible energy levels. However, owing to the mismatch between traditional electrochromic materials and the electrolyte, aqueous ECBs generally exhibit poor cycling stability which bottlenecks their practical commercialization. Herein, we present an ultrastable electrochromic system composed of lithium titanate (Li4Ti5O12, LTO) electrode and Al3+/Zn2+ hybrid electrolyte. The fully compatible system exhibits excellent redox reaction reversibility, thus leading to extremely high cycling stabilities in optical contrast (12 500 cycles with unnoticeable degradation) and energy storage (4000 cycles with 82.6% retention of capacity), superior electrochromic performances including high optical contrast (∼74.73%) and fast responses (4.35 s/7.65 s for bleaching/coloring), as well as excellent discharge areal capacity of 151.94 mAh m-2. The extraordinary cycling stability can be attributed to the robust [TiO6] octahedral frameworks which remain chemically active even upon the gradual substitution of Li+ with Al3+ in LTO over multiple operation cycles. The high-performance electrochromic system demonstrated here not only makes the commercialization of low-cost, high-safety aqueous-based electrochromic devices possible but also provides potential design guidance for LTO-related materials used in aqueous-based energy storage devices.

Fabrication of Robust, Anti-reflective, Transparent Superhydrophobic Coatings with a Micropatterned Multilayer Structure.

Transparent superhydrophobic coatings with mechanical stability, self-cleaning function, and anti-reflective property have drawn much attention due to the great potential in a variety of real-world applications. In this work, we develop an ingenious approach to construct micropatterned transparent superhydrophobic coatings with a multilayer structure (water contact angle ∼153.6°, sliding angle ∼3.2°). A micropatterned ultraviolet-cured resist frame facilitates durability, while the modified silica nanoparticles, which are housed within the micro-cavities and bonded by an epoxy-based adhesive, impart superhydrophobicity. The micropatterned multilayer surface could endure sandpaper abrasion while maintaining satisfactory hydrophobicity. The prepared surfaces also retain the excellent water repellency after water jet impact, acid submerging, and mechanical bending, suggesting that they are sustainable in the case of adverse conditions and can be integrated with objects with non-flat geometries. Further, the superhydrophobic coatings exhibit an anti-reflection property while preserving high transparency. Taken together, we envision that the design strategies here can offer a practicable route to produce transparent superhydrophobic coatings for diverse outdoor applications.

Physical, chemical, and cell toxicity properties of mature/aged particulate matter (PM) trapped in a diesel particulate filter (DPF) along with the results from freshly produced PM of a diesel engine.

The lifetime and efficiency of diesel particulate filters (DPFs) strongly depend on the proper and periodic cleaning and servicing. Unfortunately, in some cases, inappropriate methods are applied to clean the DPFs, e.g., using air compressors without proper disposal procedures which can have negative impacts on human health, the environment, and DPF's efficiency. However, there is no information available about the properties of this kind of PM. This research is therefore presented to explore the physicochemical and toxicity properties of aged PM trapped in a DPF (using compressed air for PM sampling) employing STEM, SEM, EDS, Organic Carbon Analyzer, TGA/DSC, and Raman Spectrometer for investigating the physicochemical properties, and assays of cell viability, cellular reactive oxygen species (ROS), interleukin-6, and tumor necrosis factor-alpha (TNF-α) for investigating the toxicity properties. Also, analyses from fresh PM samples from the diesel vehicle at two engine speeds are presented. It is found that at a certain/fixed PM number/mass for all three samples tested, the PM from DPF compared with the fresh PM can have both positive (particularly having the lowest water-soluble total carbon ratio) and negative impacts on human health (particularly having the highest cell death rate of 13.4%, ROS, and TNF-α) and the environment.

Physicochemical and cell toxicity properties of particulate matter (PM) from a diesel vehicle fueled with diesel, spent coffee ground biodiesel, and ethanol.

The literature shows that information about the physical, chemical, and cell toxicity properties of particulate matter (PM) from diesel vehicles is not rich as the existence of a remarkable number of studies about the combustion, performance, and emissions of diesel vehicles using renewable liquid fuels, particularly biodiesels and alcohols. Also, the PM analyses from combustion of spent coffee ground biodiesel have not been comprehensively explored. Therefore, this research is presented. Pure diesel, 90% diesel + 10% biodiesel, and 90% diesel + 9% ethanol + 1% biodiesel, volume bases, were tested under a fast idle condition. STEM, SEM, EDS, Organic Carbon Analyzer, TGA/DSC, and Raman Spectrometer were employed for investigating the PM physical and chemical properties, and assays of cell viability, cellular reactive oxygen species, interleukin-6, and tumor necrosis factor-alpha were examined for investigating the PM cell toxicity properties. It is found that the application of both biodiesel and ethanol has the potential to change the PM properties, while the impact of ethanol is more than biodiesel on the changes. Regarding the important aspects, biodiesel can be effective for better human health (due to a decrease in cell death (-60.8%)) as well as good diesel particulate filter efficiency (due to lower activation energy (-7.6%) and frequency factor (-83.2%)). However, despite a higher impact of ethanol on the reductions in activation energy (-24.8%) and frequency factor (-99.0%), this fuel causes an increase in cell death (84.1%). Therefore, biodiesel can be an appropriate fuel to have a positive impact on human health, the environment, and emissions catalysts performance, simultaneously.

Observation and Suppression of Stacking Interface States in Sandwich-Structured Quantum Dot Light-Emitting Diodes.

Interfacial quality of functional layers plays an important role in the carrier transport of sandwich-structured devices. Although the suppression of interface states is crucial to the overall device performance, our understanding on their formation and annihilation mechanism via direct characterization is still quite limited. Here, we present a thorough study on the interface states present in the electron transport layer (ETL) of blue quantum dot (QD) light-emitting diodes (QLEDs). A ZnO/ZnMgO bilayer ETL is adopted to enhance the electron injection into blue QDs. By probing the ETL band structure with photoelectron spectroscopy, we discover that substantial band bending exists at the ZnO/ZnMgO interface, elucidating the presence of a high density of interface states which hinder electron transport. By inserting a ZnO@ZMO interlayer composed of mixed ZnO and ZnMgO nanoparticles, the band bending and thus the interface states are observed to reduce significantly. We attribute this to the hybrid surface properties of ZnO@ZMO, which can annihilate the surface states of both the ZnO and ZnMgO layers. The introduction of a bridging layer has led to ∼40% enhancement in the power efficiency of blue QLEDs and noticeable performance boosts in green and red QLEDs. The findings here demonstrate a direct observation of interface states via detailed band structure studies and outline a potential pathway for eliminating these states for better performances in sandwich-structured devices.

Efficiency Improvement of Quantum Dot Light-Emitting Diodes via Thermal Damage Suppression with HATCN.

With many advantages including superior color saturation and efficiency, quantum dot light-emitting diodes (QLEDs) are considered a promising candidate for the next-generation displays. Emission uniformity over the entire device area is a critical factor to the overall performance and reliability of QLEDs. In this work, we performed a thorough study on the origin of dark spots commonly observed in operating QLEDs and developed a strategy to eliminate these defects. Using advanced cross section fabrication and imaging techniques, we discovered the occurrence of voids in the organic hole transport layer and directly correlated them to the observed emission nonuniformity. Further investigations revealed that these voids are thermal damages induced during the subsequent thermal deposition of other functional layers and can act as leakage paths in the device. By inserting a thermo-tolerant 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile (HATCN) interlayer with an optimized thickness, the thermally induced dark spots can be completely suppressed, leading to a current efficiency increase by 18%. We further demonstrated that such a thermal passivation strategy can work universally for various types of organic layers with low thermal stability. Our findings here provide important guidance in enhancing the performances and reliability of QLEDs and also other sandwich-structured devices via the passivation of heat-sensitive layers.

Robust Ultralong Lead Halide Perovskite Microwire Lasers.

Hybrid organic-inorganic lead halide perovskite microwires are potential building blocks for realizing on-chip integrated optoelectronic devices. However, the length-controllable synthesis of one-dimensional hybrid perovskite microwires has been rarely reported, especially the ones with lengths in the millimeter scale. Herein, methylammonium lead bromide (MAPbBr3) and formamidinium lead bromide (FAPbBr3) micro and milliwires are demonstrated using single-crystal PbBr2 microwires synthesized via template-free solution-phase growth as the lattice framework. Following the PbBr2 template, the as-converted perovskite microwires possess controllable lengths ranging from tens to thousands of micrometers. In addition, Fabry-Perot (FP) lasing was realized in both MAPbBr3 and FAPbBr3 microwires, attesting to their excellent crystal quality and the efficient optical confinement of the natural cavity. These unique properties result in the first demonstration of FP perovskite microwire lasers with submillimeter lengths. More interestingly, the microwire lasers show excellent photostability under repetitive pulsed laser excitation for over 8 × 106 cycles. Such findings demonstrate that the solution-converted hybrid lead bromide microwires have excellent optoelectronic performances promising for practical applications, and the size controllability indicates that this novel fabrication process may be feasible for large-scale industrial production.

Stable and Efficient Blue-Emitting CsPbBr3 Nanoplatelets with Potassium Bromide Surface Passivation.

Colloidal all-inorganic perovskites nanocrystals (NCs) have emerged as a promising material for display and lighting due to their excellent optical properties. However, blue emissive NCs usually suffer from low photoluminescence quantum yields (PLQYs) and poor stability, rendering them the bottleneck for full-color all-perovskite optoelectronic applications. Herein, a facile approach is reported to enhance the emission efficiency and stability of blue emissive perovskite nano-structures via surface passivation with potassium bromide. By adding potassium oleate and excess PbBr2 to the perovskite precursor solutions, potassium bromide-passivated (KBr-passivated) blue-emitting (≈450 nm) CsPbBr3 nanoplatelets (NPLs) is successfully synthesized with a respectably high PLQY of 87%. In sharp contrast to most reported perovskite NPLs, no shifting in emission wavelength is observed in these passivated NPLs even after prolonged exposures to intense irradiations and elevated temperature, clearly revealing their excellent photo- and thermal-stabilities. The enhancements are attributed to the formation of K-Br bonding on the surface which suppresses ion migration and formation of Br-vacancies, thus improving both the PL emission and stability of CsPbBr3 NPLs. Furthermore, all-perovskite white light-emitting diodes (WLEDs) are successfully constructed, suggesting that the proposed KBr-passivated strategy can promote the development of the perovskite family for a wider range of optoelectronic applications.

CNSi/MXene/CNSi: Unique Structure with Specific Electronic Properties for Nanodevices.

2D materials have been interesting for applications into nanodevices due to their intriguing physical properties. In this work, four types of unique structures are designed that are composed of MXenes and C/N-Si layers (CNSi), where MXene is sandwiched by the CNSi layers with different thicknesses, for their practical applications into integrated devices. The systematic calculations on their elastic constants, phonon dispersions, and thermodynamic properties show that these structures are stable, depending on the composition of MXene. It is found: 1) different from MXene or N-functionalized MXene (M2 CN2 ), SiN2 /M2 X/SiN2 possess new electronic properties with free carriers only in the middle, leading to 2D free electron gas; 2) CNSi/MXene/CNSi shows an intrinsic Ohmic semiconductor-metal-semiconductor (S-M-S) contact, which is potential for applications into nanodevices; and 3) O/M2 C/SiN2 and N/M2 C/OSiN are also stable and show different electronic properties, which can be semiconductor or metal as a whole depending on the interface. A method is further proposed to fabricate the 2D structures based on the industrial availability. The findings may provide a novel strategy to design and fabricate the 2D structures for their application into nanodevices and integrated circuits.

Aluminum-Based Surface Polymerization on Carbon Dots with Aggregation-Enhanced Luminescence.

Aggregation-induced luminescence quenching of carbon nanodots (CDs) is the main obstacle for their applications in solid-state light emitting devices. Herein, we developed a one-step synthesis of solid-state emissive CDs with surface aluminum-based polymerization by adding AlCl3 in citric acid and urea via a microwave-heating dehydration process. Due to the strong coordination ability of Al ions with N and O atoms, considerable steric hindrance of Al-based cross-linked polymerization was introduced on the surface of the CDs, which not only avoided aggregation of the green emissive carbon cores but also facilitated efficient energy transfer from the blue emissive polymerized surface to the green emissive carbon cores in aggregates, leading to enhanced green emissions with a photoluminescence quantum yield (PLQY) of 72.7% in the solid state.

Design of 2D materials - MSi2CxN4-x (M = Cr, Mo, and W; x = 1 and 2) - with tunable electronic and magnetic properties.

Two-dimensional (2D) materials have attracted increasing interest in the past decades due to their unique physical and chemical properties for diverse applications. In this work, we present a first-principles design on a novel 2D family, MSi2CxN4-x (M = Cr, Mo, and W; x = 1 and 2), based on density-functional theory (DFT). We find that all MSi2CxN4-x monolayers are stable by investigating their mechanic, dynamic, and thermodynamic properties. Interestingly, we see that the alignment of magnetic moments can be tuned to achieve non-magnetism (NM), ferromagnetism (FM), anti-ferromagnetism (AFM) or paramagnetism (PM) by arranging the positions of carbon atoms in the 2D systems. Accordingly, their electronic properties can be controlled to obtain semiconductor, half-metal, or metal. The FM states in half-metallic 2D systems are contributed to the hole-mediated double exchange, while the AFM states are induced by super-exchange. Our findings show that the physical properties of 2D systems can be tuned by compositional and structural engineering, especially the layer of C atoms, which may provide guidance on the design and fabrication of novel 2D materials with projected properties for multi-functional applications.

Multi-Phase Heterostructure of CoNiP/Cox P for Enhanced Hydrogen Evolution Under Alkaline and Seawater Conditions by Promoting H2 O Dissociation.

Hydrogen evolution reaction (HER) is a key step for electrochemical energy conversion and storage. Developing well defined nanostructures as noble-metal-free electrocatalysts for HER is promising for the application of hydrogen technology. Herein, it is reported that 3D porous hierarchical CoNiP/Cox P multi-phase heterostructure on Ni foam via an electrodeposition method followed by phosphorization exhibits ultra-highly catalytic activity for HER. The optimized CoNiP/Cox P multi-phase heterostructure achieves an excellent HER performance with an ultralow overpotential of 36 mV at 10 mA cm-2 , superior to commercial Pt/C. Importantly, the multi-phase heterostructure shows exceptional stability as confirmed by the long-term potential cycles (30,000 cycles) and extended electrocatalysis (up to 500 h) in alkaline solution and natural seawater. Experimental characterizations and DFT calculations demonstrate that the strong electronic interaction at the heterointerface of CoNiP/CoP is achieved via the electron transfer from CoNiP to the heterointerface, which directly promotes the dissociation of water at heterointerface and desorption of hydrogen on CoNiP. These findings may provide deep understanding on the HER mechanism of heterostructure electrocatalysts and guidance on the design of earth-abundant, cost-effective electrocatalysts with superior HER activity for practical applications.