RESUMEN
Reproducible aerosol generation in combination with stable aerosol properties are essential prerequisites for compliant performance of acute or repeated inhalation toxicity tests of particulate materials according to OECD TG 403, 436, 412, or 413. A frequent problem of powder aerosol generation is the formation of coarse agglomerates with low shear resistance, which are beyond the tolerable size range but not detected by the prescribed aerodynamic measurement techniques by cascade impactor as the measurement conditions cause a disintegration into smaller fragments. But such agglomerates are observed during the transport to the inhalation chambers. These effects particularly apply to high mass concentrations and low-density powders, i.e., pyrogenic oxides. This study describes the transport influence in the airflow on the change of powder aerosols and on their respirability. A simplified short tube set-up was developed for the aerosol transport pre-tests, which allows the determination of the optimal aerosol formation conditions for the inhalation tests. The particles were measured with low shear using laser diffraction measurement or optical particle counters. The calculation of the aerodynamic particle sizes prescribed in the guidelines requires knowledge of the effective particle density of the porous aerosol particles. A practicable method for determining these is presented and described. In the outlook, first low concentration measurements show that clear agglomeration effects can also occur at particle concentrations around 20â¯mg/m³.
RESUMEN
The article by Balwierz et al [...].
Asunto(s)
Cosméticos , Salud Pública , Carcinógenos/toxicidadRESUMEN
Synthetic amorphous silica (SAS) is used as additive in a variety of industrial applications for many decades and has been approved to be used in food, food contact materials, pharmaceuticals, and cosmetics. Due its internal structure, SAS is considered as a nanomaterial, thus it is affected by a general safety discussion. Based on the production process, SAS for cosmetic application is a nanomaterial by the EU Recommendation, although it was not considered as such, because the solely size-dependent definitions of the term "nanomaterial" emerged in recent times first in Recommendation 2011/696/EU. Therefore, former physicochemical and toxicological evaluations of SAS were already performed on nanomaterials, however, without being addressed as such. Safety concerns can only emerge if two criteria, (toxicological) hazard and exposure towards the substance is fulfilled at the same time. In case of SAS, the Scientific Committee on Consumer Safety (SCCS) challenged provided data to be insufficient to draw a conclusion regarding the safety of SAS and thus, requested further investigations, in particular by exploring skin penetration of particulate SAS.Investigation of specific particulate substances in skin penetration tests is an analytical challenge. The number of available analytical techniques that are capable to detect nanomaterials in complex matrices, like receptor fluids from skin penetration testing, are limited and still emerging. In the new studies, a comprehensive set of analytical techniques were used to investigate the skin penetration potential of SAS. Particle-sensitive, element and particle-specific combinations of techniques and different sample preparation procedures, that respected the particulate nature of SAS, were used to detect SAS in receptor fluids directly. In addition, electron microscopic techniques were used to examine different layers of skin to detect adsorbed SAS.The combination of Asymmetric Flow Field-Flow Fractionation (AF4) in combination with Inductively Coupled Plasma Mass Spectrometry (ICP-MS) for examination of receptor fluids and Scanning Electron Microscopy coupled with Energy Dispersive X-ray spectroscopy (SEM/EDX) for examination of skin itself, were identified as suitable techniques for the detection of SAS in skin penetration tests. Data from literature was used to compare the results of the studies with the outcome of other test systems (other particles, other techniques). Both, the test results, and literature evaluation led to the conclusion, that SAS does not penetrate skin. Based on this outcome and local and systemic dermal toxicity review of SAS, it can be concluded that dermal application of SAS in cosmetic formulations is negligible.
RESUMEN
Low density powders have a bulk density of less than 100 kg/m3 and are produced technically by flame pyrolysis of silicon tetrachloride (pyrogenic powders such as pyrogenic silica) or wet-chemically by sol-gel processes (e.g. silica-gel) or precipitation reactions using sodium silicate solution and a mineral acid. The transport and alteration behavior of aerosols from low density powders was investigated in a device for toxicological inhalation studies. The test conditions corresponded to those for acute toxicology studies according to OECD Guideline 436. The use of cascade impactors, required by guideline, has not proven successful for low density powders as the fragile agglomerate structures are destroyed during the measurement. As an alternative and non-invasive measurement method, laser diffraction spectroscopy has proved very successful in the present investigations. In particular, aerosols from pyrogenic powders of low density showed a distinctive tendency to re-agglomerate, especially at concentrations >500 mg/m3mm3. Investigation results indicate that aerosol particle size must be monitored over the entire acute inhalation test period for acute inhalation studies to be performed reliably.