RESUMEN
All-solid-state batteries using Si as the anode have shown promising performance without continual solid-electrolyte interface (SEI) growth. However, the first cycle irreversible capacity loss yields low initial Coulombic efficiency (ICE) of Si, limiting the energy density. To address this, we adopt a prelithiation strategy to increase ICE and conductivity of all-solid-state Si cells. A significant increase in ICE is observed for Li1Si anode paired with a lithium cobalt oxide (LCO) cathode. Additionally, a comparison with lithium nickel manganese cobalt oxide (NCM) reveals that performance improvements with Si prelithiation is only applicable for full cells dominated by high anode irreversibility. With this prelithiation strategy, 15% improvement in capacity retention is achieved after 1000 cycles compared to a pure Si. With Li1Si, a high areal capacity of up to 10 mAh cm-2 is attained using a dry-processed LCO cathode film, suggesting that the prelithiation method may be suitable for high-loading next-generation all-solid-state batteries.
RESUMEN
All-solid-state batteries have recently gained considerable attention due to their potential improvements in safety, energy density, and cycle-life compared to conventional liquid electrolyte batteries. Sodium all-solid-state batteries also offer the potential to eliminate costly materials containing lithium, nickel, and cobalt, making them ideal for emerging grid energy storage applications. However, significant work is required to understand the persisting limitations and long-term cyclability of Na all-solid-state-based batteries. In this work, we demonstrate the importance of careful solid electrolyte selection for use against an alloy anode in Na all-solid-state batteries. Three emerging solid electrolyte material classes were chosen for this study: the chloride Na2.25Y0.25Zr0.75Cl6, sulfide Na3PS4, and borohydride Na2(B10H10)0.5(B12H12)0.5. Focused ion beam scanning electron microscopy (FIB-SEM) imaging, X-ray photoelectron spectroscopy (XPS), and electrochemical impedance spectroscopy (EIS) were utilized to characterize the evolution of the anode-electrolyte interface upon electrochemical cycling. The obtained results revealed that the interface stability is determined by both the intrinsic electrochemical stability of the solid electrolyte and the passivating properties of the formed interfacial products. With appropriate material selection for stability at the respective anode and cathode interfaces, stable cycling performance can be achieved for Na all-solid-state batteries.
RESUMEN
To enhance the compatibility between the polymer-based electrolytes and electrodes, and promote the interfacial ion conduction, a novel approach to engineer the interfaces between all-solid-state composite polymer electrolyte and electrodes using thin layers of ferroelectrics is introduced. The well-designed and ferroelectric-engineered composite polymer electrolyte demonstrates an attractive ionic conductivity of 7.9 × 10-5 S cm-1 at room temperature. Furthermore, the ferroelectric engineering is able to effectively suppress the growth of solid electrolyte interphase (SEI) at the interface between polymer electrolytes and Na metal electrodes, and it can also enhance the ion diffusion across the electrolyte-ferroelectric-cathode/anode interfaces. Notably, an extraordinarily high discharge capacity of 160.3 mAh g-1 , with 97.4% in retention, is achieved in the ferroelectric-engineered all-solid-state Na metal cell after 165 cycles at room temperature. Moreover, outstanding stability is demonstrated that a high discharge capacity retention of 86.0% is achieved over 180 full charge/discharge cycles, even though the cell has been aged for 2 months. This work provides new insights in enhancing the long-cyclability and stability of solid-state rechargeable batteries.
RESUMEN
The surface feature of solid electrolytes fundamentally governs their own physical properties and significantly affects the interaction with the electrode materials. The evaluation of interfacial contact between the electrolyte and the metallic anode is largely relied on the macroscopic contact angle measurement, which is influenced by the intrinsic wettability and the microstructure of the electrolyte. In this work, the surface chemistry of the solid electrolyte is first regulated via facile thermal treatments. Then, scanning probe microscopy (SPM)-based techniques are comprehensively adopted to study the interaction between the electrolyte and metallic anode at the nanoscale. By manipulating the overpotential applied on the SPM tip, the mobile sodium ions at the subsurface of the solid electrolyte can be extracted toward the surface, and the eventual topography of the products is deliberately correlated with the sodium wettability. In this context, the impact of surface treatment on the sodium wettability of the surface layer is systematically evaluated based on the topographic evolution at the nanoscale. Furthermore, the local electrochemical reaction dynamics is revealed by correlating the surface ionic activity and current-voltage (I-V) curves. This work presents a new methodology to effectively evaluate the sodium wettability of the solid electrolyte, and these findings can provide meaningful implications to the surface engineering of ceramic electrolytes for high-performance solid-state batteries.
RESUMEN
Sodium-metal batteries have strong potential to be utilized as stationary high energy density storage devices. Owing to its high ionic conductivity, low electronic conductivity and relatively easy fabrication, NASICON-structure electrolyte (Na3Zr2Si2PO12) is one of the potential candidates to be considered in the solid-state sodium-metal batteries at room temperature. However, the large interfacial resistance between the solid-state electrolyte and the metallic sodium is known to limit the critical current density (CCD) of the cell. In this study, a simple and cost-effective annealing process is introduced to the electrolyte preparation to improves its interface with metallic sodium. X-ray photoelectron spectroscopy and scanning probe microscopy show that Si forms bonds with the surface functional groups when exposed to the ambient condition. With the removal of surface contamination as well as a partially reduced electrolyte surface, the annealed electrolyte shows an extremely small interfacial resistance of 11 Ω cm2 and a high CCD of 0.9 mA cm-2. This study provides an insight on the electrolyte surface preparation and its significant in a sodium-metal solid-state battery.
RESUMEN
To tackle the global restriction on the use of lead-based materials, a feasible strategy of developing a piezoelectric ceramic with a ferroelectric- and relaxor-coexisted hybrid state is proposed in order to reduce the energy barrier as well as to assist polarization rotation. A significantly enhanced piezoelectric coefficient, d33, of 173 pC/N along with a broadened high-temperature stability above 300 °C has been obtained. Further probing via piezoresponse force microscopy unveils the grain boundary-governed domain structures with complicated configurations, suggesting close correlations with the coexistence of ferroelectric and relaxor states. This work demonstrates a recipe for establishing a novel grain-based ferroelectric-relaxor hybrid state with improved piezoelectric performance, which can further be beneficial for realistic applications.
RESUMEN
NASICON-type of solid-state electrolyte, Na3Zr2Si2PO12 (NZSP), is one of the potential solid-state electrolytes for all-solid-state Na battery and Na-air battery. However, in solid-state synthesis, high sintering temperature above 1200 °C and long duration are required, which led to loss of volatile materials and formation of impurities at the grain boundaries. This hampers the total ionic conductivity of NZSP to be in the range of 10-4 S cm-1. Herein, we have reduced both the sintering temperature and time of the NZSP electrolyte by sintering the NZSP powders with different amounts of Na2SiO3 additive, which provides the liquid phase for the sintering process. The addition of 5 wt % Na2SiO3 has shown the highest total ionic conductivity of 1.45 mS cm-1 at room temperature. A systematic study of the effect of Na2SiO3 on the microstructure and electrical properties of the NZSP electrolyte is conducted by the structural study with the help of morphological and chemical observations using X-ray diffraction (XRD), scanning electron microscopy, and using focused ion-beam-time of flight-secondary ion mass spectroscopy. The XRD results revealed that cations from Na2SiO3 diffused into the bulk change the stoichiometry of NZSP, leading to an enlarged bottleneck area and hence lowering activation energy in the bulk, which contributes to the increment of the bulk ion conductivity, as indicated by the electrochemical impedance spectroscopy result. In addition, higher density and better microstructure contribute to improved grain boundary conductivity. More importantly, this study has achieved a highly ionic conductive NZSP only by facile addition of Na2SiO3 into the NZSP powder prior to the sintering stage.
RESUMEN
All-solid-state lithium metal batteries (ASSLiMB) have been considered as one of the most promising next-generation high-energy storage systems that replace liquid organic electrolytes by solid-state electrolytes (SSE). Among many different types of SSE, NASICON-structured Li1+ xAl xGe2- x(PO3)4 (LAGP) shows high a ionic conductivity, high stability against moisture, and wide working electrochemical windows. However, it is unstable when it is in contact with molten Li, hence largely limiting its applications in ASSLiMB. To solve this issue, we have studied reaction processes and mechanisms between LAGP and molten Li, based on which a failure mechanism is hence proposed. With better understanding the failure mechanism, a thin thermosetting Li salt polymer, P(AA- co-MA)Li, layer is coated on the bare LAGP pellet before contacting with molten Li. To further increase the ionic conductivity of P(AA- co-MA)Li, LiCl is added in P(AA- co-MA)Li. A symmetric cell of Li/interface/LAGP/interface/Li is prepared using molten Li-Sn alloy and galvanically cycled at current densities of 15, 30, and 70 µA cm-2 for 100 cycles, showing stable low overpotentials of 0.036, 0.105, and 0.257 V, respectively. These electrochemical results demonstrate that the interface coating of P(AA- co-MA)Li can be an effective method to avoid an interfacial reaction between the LAGP electrolyte and molten Li.
