Method to obtain a plasma rich in platelet- and plasma-growth factors based on water evaporation.

Platelet-Rich Plasma, also known as PRP, is an autologous biologic product used in medicine as a treatment for tissue repair. Nowadays, the majority of PRP obtention methods enrich only platelets, not considering extraplatelet biomolecules, which take part in several cell processes. In the present work, a novel PRP preparation method was developed to obtain a PRP rich in both platelet and plasma extraplatelet molecules. The method is based on the evaporation of the water of the plasma using a rotary evaporator. With this new methodology an increase in plasmatic growth factors and, as a consequence, a better dermal fibroblast cell viability was achieved, compared to a standard PRP formulation. This novel PRP product obtained with this new methodology showed promising results in vitro as an improved PRP treatment in future application.

High survival rate after the combination of intrameniscal and intraarticular infiltrations of platelet-rich plasma as conservative treatment for meniscal lesions.

PURPOSE: To evaluate the efficacy of applying a combination of intrameniscal and intraarticular infiltrations of Platelet-Rich Plasma (PRP) in patients with meniscal tears, analyzing its failure rate and clinical evolution, as well as factors that may influence the positive response to this treatment. METHODS: Three hundred and ninety-two cases out of 696 met the inclusion criteria and were included in this work. Survival and patient-reported outcome measure (PROM) were collected and analyzed. Survival rate was defined as the percentage of patients who did not undergo meniscus surgery during their follow-up time. Patients were asked to complete the Knee injury and Osteoarthritis Outcome Score (KOOS) at baseline, 6 months and 18 months. Other patient- and pathology-related variables were collected. Blood and PRP samples were randomly tested as a quality control measure. Survival and comparative statistical tests, and multivariate regression were performed for the analysis of the variables. RESULTS: The PRP applied had a platelet concentration factor of 1.9X in respect to blood levels, with no leukocytes or erythrocytes. Thirty-eight patients required surgical intervention after treatment reaching a survival rate of 90.3% with an estimated mean survival time of 54.4 months. The type of injury (P = 0.002) and the presence of chondropathy were risk factors for surgical intervention after PRP treatment (P = 0.043). All KOOS scores showed a significant statistical increase from baseline to 6 months (N = 93) and 18 months (N = 66) (P < 0.0001). The number of cases with minimal clinically important improvement (MCII) at 6 months and 18 months post-treatment was 65 (69.9%) and 43 (65.2%), respectively. CONCLUSION: The combination of intrameniscal and intraarticular PRP infiltrations is a valid conservative treatment for meniscal injuries avoiding the need for surgical intervention. Its efficacy is higher in horizontal tears and decreases when joint degeneration is present. LEVEL OF EVIDENCE: Level IV.

Custom 3D-Printed Cutting Guides for Femoral Osteotomy in Rotational Malalignment Due to Diaphyseal Fractures: Surgical Technique and Case Series.

Femoral shaft fractures are one of the most common injuries in trauma patients. The gold standard treatment consists of closed reduction and intramedullary nailing, providing a high fracture healing rate and allowing early mobilization. However, rotational malalignment is a well-known complication following this procedure, and excessive femoral anteversion or femoral retroversion can trigger functional complaints. In order to achieve the ideal degree of femoral rotation, a 3D planning and printing cutting guides procedure was developed to correct femoral malrotation. A patient series with malalignment after a femoral diaphyseal fracture was operated on with the customized guides and evaluated in this study. Computed tomography scans were performed to accurately determine the number of degrees of malrotation, allowing the design of specific and personalized surgical guides to correct these accurately. Once designed, they were produced by 3D printing. After surgery with the customized guides to correct femoral malrotation, all patients presented a normalized anteversion angle of the femur (average -10.3°, range from -5° to -15°), according to their contralateral limb. These data suggest that the use of customized cutting guides for femoral osteotomy is a safe and reproducible surgical technique that offers precise results when correcting femoral malrotation.

Intraosseous infiltrations of Platelet-Rich Plasma for severe hip osteoarthritis: A pilot study.

OBJECTIVE: Addressing the subchondral bone through intraosseous infiltrations of Platelet-Rich Plasma (PRP) may improve the effectiveness of this technique for severe hip osteoarthritis (HOA). METHODS: Forty patients with HOA degree 2 and 3 according to the Tönnis scale were recruited for this study. They were susceptible to a total hip arthroplasty, without response to previous treatment based on intraarticular infiltrations of PRP. Patients received a combination of intraosseous injections into the acetabulum and the femoral head, as well as intraarticular PRP infiltrations. The clinical outcome was evaluated at 2, 6 and 12 months using the Hip Osteoarthritis Outcome Score (HOOS) and the Western Ontario and McMaster Universities Osteoarthritis (WOMAC) Index. RESULTS: At 2, 6 and 12 months, patients had significant pain improvement according to HOOS pain, WOMAC pain, and VAS scores. After the treatment, the percentage of patients with minimal clinically important improvement was 40% (16 over 40 patients) at 2 months, 37.5% (15 over 40) at 6 months, and 40% (16 over 40) at 12 months. Conclusion: The combination of intra-articular and intra-osseous infiltrations of PRP showed a pain reduction and improvement in hip joint functionality up to 12 months in patients with severe HOA, with no severe adverse effects.

Application of 3D technology and printing for femoral derotation osteotomy: case and technical report.

In some surgical techniques like femoral derotation osteotomy, accuracy is a key factor that often is not optimal because of the lack of appropriate technology. 3D printing is emerging in many professional areas and its use in the medical field may enhance the results of certain surgeries. This case describes a patient who underwent an intramedullary nail fixation to treat a femoral shaft fracture. After nine months, the patient presented hip pain and "in toe" walking caused by a malrotation produced during the surgery. To address the consequent femoral derotation osteotomy, 3D technology was used throughout the whole process. A 3D model of the patient's femur was created to conduct a real and accuracy assessment of femoral anteversion. Then, a customized surgical guide was designed and printed to ensure the proper alignment during surgery. Given the success of this surgery, 3D printing can be considered a quick and inexpensive tool to improve surgical results.