Vaginal residence and pharmacokinetic preclinical study of topical vaginal mucoadhesive W/S emulsions containing ciprofloxacin.

The aim of this work is to test the in vivo behavior of a mucoadhesive vaginal emulsion resistant to the clearance of vaginal fluids using ciprofloxacin (CPX) as an anti-infective model of drug. CPX is a broad-spectrum antibiotic used in the treatment of sexual tissues infections, as intravenous injection in a dose of 20 mg every 12 h. In this study, CPX was incorporated in water in silicone (W/S) mucoadhesive emulsions and the in vivo residence time and the CPX in vivo absorption and distribution to the sexual organs was studied using the rat as animal model. W/S emulsion shows excellent in vitro bioadhesion having high resistance to the vaginal fluids clearance. The drug release profiles show a constant release of CPX during at least 6 h according to a zero-order kinetics. In vivo computerized PET/CT Image Analysis after intravaginal administration to rats indicates that W/S emulsions remain in the vaginal area for a long time and shows a good absorption of the radiotracers used as markers through the vaginal mucosa. Ciprofloxacin pharmacokinetic studies developed after the single intravaginal administration of W/S emulsion shows a good absorption and distribution of CPX on the uterus and ovarian tissue. A significant concentration of CPX in the sexual tissues was observed after 24 h of administration of W/S emulsion. Therefore, W/S emulsions have a good in vivo residence and drug release in the vaginal mucosae showing a great potential for the treatment of sexual tissues infections, as vaginal bioadhesive delivery systems of antinfectious drugs.

Effect of roll compaction on granule size distribution of microcrystalline cellulose-mannitol mixtures: computational intelligence modeling and parametric analysis.

Dry granulation using roll compaction is a typical unit operation for producing solid dosage forms in the pharmaceutical industry. Dry granulation is commonly used if the powder mixture is sensitive to heat and moisture and has poor flow properties. The output of roll compaction is compacted ribbons that exhibit different properties based on the adjusted process parameters. These ribbons are then milled into granules and finally compressed into tablets. The properties of the ribbons directly affect the granule size distribution (GSD) and the quality of final products; thus, it is imperative to study the effect of roll compaction process parameters on GSD. The understanding of how the roll compactor process parameters and material properties interact with each other will allow accurate control of the process, leading to the implementation of quality by design practices. Computational intelligence (CI) methods have a great potential for being used within the scope of quality by design approach. The main objective of this study was to show how the computational intelligence techniques can be useful to predict the GSD by using different process conditions of roll compaction and material properties. Different techniques such as multiple linear regression, artificial neural networks, random forest, Cubist and k-nearest neighbors algorithm assisted by sevenfold cross-validation were used to present generalized models for the prediction of GSD based on roll compaction process setting and material properties. The normalized root-mean-squared error and the coefficient of determination (R2) were used for model assessment. The best fit was obtained by Cubist model (normalized root-mean-squared error =3.22%, R2=0.95). Based on the results, it was confirmed that the material properties (true density) followed by compaction force have the most significant effect on GSD.

MCC-mannitol mixtures after roll compaction/dry granulation: percolation thresholds for ribbon microhardness and granule size distribution.

In roll compaction, the specific compaction force, the gap width and the roll speed are the most important settings as they have a high impact in the products obtained. However the mechanical properties of the mixture being compacted are also critical. For this reason, a multilevel full factorial design including these parameters as factors plus three repetitions of the center point was performed for microcrystalline cellulose, mannitol and five binary mixtures (15, 30, 50, 70 and 85% MCC). These two reference excipients were chosen in order to investigate the plastic/brittle behavior of mixtures for the roll compaction process. These materials were roll compacted in a 3-W-Polygran® 250/50/3 (Gerteis) and the ribbons obtained were collected and milled into granules which were characterized regarding granule size distribution. After statistical evaluation, it was found that the most critical factors affecting the D10, D50, D90 and the fines fraction from the granules were the gap width and the specific compaction force, as well as the proportion of MCC together with its quadratic effect and the interaction between force and proportion of MCC. The microhardness of the ribbons from the center point as well as the D10, D50, D90 and the fines fraction from the granules produced at these same conditions were characterized. In all the cases, the proportion of MCC, i.e. the composition of the mixture, showed also an important effect on these properties measured. In this sense, the percolation theory was applied in order to study further the importance of the plastic/brittle ratio by calculating the percolation threshold or the limit over which the behavior of the system changes. This resulted in values of 34% for the HU (expression of microhardness), 27% and 28% for the D10 and fines, respectively (percolation of MCC) and 84% and 85% for the D50 and D90, respectively (percolation of mannitol).

Effect of roll-compaction and milling conditions on granules and tablet properties.

Dry granulation is an agglomeration process used to produce size-enlarged particles (granules), improving the handling properties of powders such as flowability. In this process, powders are compacted using a roll press to produce ribbons, which are milled in granules used further in the tableting process. The granule and tablet properties are influenced by the existence of different designs of the roll compactors, milling systems and the interaction between process parameters and raw material properties. The main objective of this work was to investigate how different roll-compaction conditions and milling process parameters impact on ribbons, granules and tablet properties, highlighting the role of the sealing system (cheek plates and rimmed roll). In this context, two common excipients differing in their mechanical behaviour (MCC and mannitol) are used. The study is based on the analysis of granule size distribution together with the characterization of loss of compactability during die compaction. Results show that the tensile strength of tablets is lower when using granules than when the raw materials are compressed. Moreover, the plastic material (MCC) is more sensitive than the brittle one (mannitol). Regarding the roll-force, it is observed that the higher the roll force, the lower the tensile strength of tablets from granulated material is. These findings are in agreement with the literature. The comparison of sealing systems shows that the rimmed-roll system leads to slightly stronger tablets than the use of cheek plates. In addition, the use of the rimmed-roll system reduces the amount of fines, in particular when high roll force is applied. Overall, it can be concluded that roll-compaction effect is predominant over the milling effect on the production of fines but less significant on the tablet properties. This study points out that the balance between a good flowability by reducing the amount of fines and appropriate tablet strength is achieved with rimmed-roll and the highest roll-force used.