RESUMEN
The development of sensitive, selective, and reliable gaseous hydrogen peroxide (H2O2) sensors operating at room temperature still represents a remaining challenge. In this work, we have investigated and combined the advantageous properties of a two-dimensional Ti3C2Tx MXene material that exhibits a large specific surface area and high surface activity, with favorable conducting and stabilizing properties of chitosan. The MXene-chitosan membrane was deposited on the ferrocyanide-modified screen-printed working carbon electrode, followed by applying poly(acrylic acid) as an electrolyte and accumulation medium for gaseous H2O2. The sensor showed highly sensitive and selective electroanalytical performance for detecting trace concentrations of gaseous H2O2 with a very low detection limit of 4 µg m-3 (4 ppbv), linear response in the studied concentration range of 0.5-30.0 mg m-3, and good reproducibility with an RSD of 1.3%. The applicability of the sensor was demonstrated by point-of-interest detection of gaseous H2O2 during the real hair bleaching process with a 9 and 12% H2O2 solution.
RESUMEN
Black phosphorus (BP), a promising 2D material for electronics, energy storage, catalysis, and sensing, has sparked a research boom. However, exfoliated thin-layered BP is unstable and can easily be degraded under environmental conditions, severely limiting its practical applications. In this context, a simple and cost-effective method has been proposed that involves electrochemically exfoliating BP and simultaneously electrochemically depositing aluminum oxide (AlO x ) for passivation of the exfoliated BP. The ambient stability of the exfoliated BP is studied using a time-dependent atomic force microscope (AFM). The AlO x capping layer significantly improves the environmental stability of BP compared to uncapped BP. The thermal stability of the resulting BP is evaluated using power-dependent Raman spectroscopy. The results show that the AlO x -passivated BP has increased thermal stability, with only a slight shift in peak position toward higher Raman power intensity. These properties can make the material suitable for stable energy storage devices. Interestingly, the electrochemical exfoliation and passivation processes resulted in the BP with a twist angle (9.86°), which is expected to exhibit unique electronic properties similar to those of graphene with a twist angle.
RESUMEN
Considerable improvements in the electrocatalytic activity of 2D metal phosphorous trichalcogenides (M2 P2 X6 ) have been achieved for water electrolysis, mostly with MII 2 [P2 X6 ]4- as catalysts for hydrogen evolution reaction (HER). Herein, MI MIII P2 S6 (MI = Cu, Ag; MIII = Sc, V, Cr, In) are synthesized and tested for the first time as electrocatalysts in alkaline media, towards oxygen reduction reaction (ORR) and HER. AgScP2 S6 follows a 4 e- pathway for the ORR at 0.74 V versus reversible hydrogen electrode; CuScP2 S6 is active for HER, exhibiting an overpotential of 407 mV and a Tafel slope of 90 mV dec-1 . Density functional theory models reveal that bulk AgScP2 S6 and CuScP2 S6 are both semiconductors with computed bandgaps of 2.42 and 2.23 eV, respectively and overall similar electronic properties. Besides composition, the largest difference in both materials is in their molecular structure, as Ag atoms sit at the midpoint of each layer alongside Sc atoms, while Cu atoms are raised to a similar height to S atoms, in the external segment of the 2D layers. This structural difference probably plays a fundamental role in the different catalytic performances of these materials. These findings show that MI (Cu, Ag) together with Sc(MIII ) leads to promising achievements in MI MIII P2 S6 materials as electrocatalysts.
RESUMEN
Promising applications of metal phosphorous trichalcogenides (M2 P2 X6 or MPX3 ) have been predicted in optoelectronics, photoelectrocatalysis, and water-splitting reactions, mainly due to its wide bandgap. Transition metals are widely used in the synthesis of MPX3 , however, divalent cations of alkaline earth metals can also be constituents in MPX3 2D layered structures. Herein, MgPX3 (X = S, Se) are synthesized and their photoelectrochemical (PEC) activity is tested in the hydrogen evolution and oxygen evolution reaction (OER) regions under a wide range of wavelengths. MgPSe3 photoelectrode shows the best PEC performance with a response of 1.6 ± 0.1 mA cm-2 under 420 nm. In the light-assisted OER, a 200 mV improvement is obtained in the overpotential at 10 mA cm-2 for MgPSe3 . The better performance of MgPSe3 is consistent with its lower optical bandgap (Eg = 3.15 eV), as a result of the variation of electronegativity between selenide and sulfide.
Asunto(s)
Magnesio , Agua , Hidrógeno/química , Oxígeno , Fósforo , Agua/químicaRESUMEN
Two-dimensional (2D) layered materials are currently one of the most explored materials for developing efficient and stable electrocatalysts in energy conversion applications. Some of the 2D metal phosphorous trichalcogenides (M2P2X6 or MPX3 in its simplified form) have been reported to be useful catalysts for water splitting, although results have been less promising for the sluggish oxygen evolution reaction (OER) due to insufficient activity or compromised stability. Herein, we report the OER catalysis of a series of M2P2X6 (M2+ = Mn, Fe, Co, Zn, Cd; X = S, Se). From the series of MPX3, CoPS3 yields the best results with an overpotential within the range of values usually obtained for IrO2 or RuO2 catalysts. The liquid-phase exfoliation of CoPS3 even improves the OER activity due to abundant active edges of the downsized sheets, accompanied by the presence of surface oxides. The influence of the OER medium and underlying substrate electrode is studied, with the exfoliated CoPS3 reaching the lowest overpotential at 234 mV at a current density of 10 mA/cm2, also able to sustain high current densities, with an overpotential of 388 mV at a current density of 100 mA/cm2, and excellent stability after multiple cycles or long-term operation. Quantum chemical models reveal that these observations are likely tied to moieties on CoPS3 edges, which are responsible for low overpotentials through a two-site mechanism. The OER performance of exfoliated CoPS3 reported herein yields competitive values compared to those reported for other Co-based and MPX3 in the literature, thus holding substantial promise for use as an efficient material for the anodic water-splitting reaction.