Photo-engineered optoelectronic properties of indium tin oxide via reactive laser annealing.

Transparent conductive oxides are appealing materials for optoelectronic and plasmonic applications as, amongst other advantages, their properties can be modulated by engineering their defects. Optimisation of this adjustment is, however, a complex design problem. This work examined the modification of the carrier transport properties of sputtered tin-doped indium oxide (ITO) via laser annealing in reactive environments. We relate the optical modifications to the structural, compositional, and electronic properties to elucidate the precise mechanisms behind the reactive laser annealing (ReLA) process. For sufficiently high laser fluence, we reveal an ambient-dependent and purely compositional modulation of the carrier concentration of ITO thin films. Hereby, we demonstrate that ReLA utilises the precise energy delivery of photonic processing to enhance the carrier mobility and finely tune the carrier concentration without significantly affecting the crystal structure. Exploitation of this phenomena may enable one to selectively engineer the optoelectronic properties of ITO, promising an alternative to the exploration of new materials for optoelectronic and photonic applications.

Tunable Infrared Plasmonic Properties of Epitaxial Ti1-xMgxN(001) Layers.

Optical transmission and reflection spectra in combination with ellipsometry and transport measurements on epitaxial rocksalt structure Ti1-xMgxN(001) layers with 0.00 ≤ x ≤ 0.49 are employed to explore their potential as refractory infrared plasmonic materials. A red shift in the reflection edge ℏωe from 2.0 to 0.8 eV and the corresponding unscreened plasma energy ℏωpu from 7.6 to 4.7 eV indicate a linear reduction in the free carrier density N with increasing x. However, nitrogen vacancies in Mg-rich samples act as donors, resulting in a minimum N = 1.6 × 1022 cm-3 for x = 0.49. Photoelectron valence band spectra confirm the diminishing conduction band density of states and indicate a 0.9 eV decrease in the Fermi level as x increases from 0 to 0.49. The dielectric function ε = ε1 + iε2 can be divided into a low-energy spectral region where intraband transitions result in large negative and positive ε1 and ε2, respectively, and a higher energy interband transition region with both ε1 and ε2 > 0. The screened plasma energy Eps that separates these two regions red-shifts from 2.6 to 1.3 eV for x = 0-0.39, indicating a tunable plasmonic activity that extends from the visible to the infrared (470-930 nm). Electron transport measurements indicate a metallic temperature coefficient of resistivity (TCR) for TiN-rich alloys with x ≤ 0.26 but weak carrier localization and a negative TCR <60 K for x = 0.39 and <300 K for x = 0.49, attributed to Mg alloying-induced disorder. The plasmonic quality factor Q is approximately an order of magnitude larger than what was previously reported for polycrystalline Ti1-xMgxN, making Ti1-xMgxN(001) layers competitive with Ti1-xScxN(001).

Graphene-Wrapped Copper Nanoparticles: An Antimicrobial and Biocompatible Nanomaterial with Valuable Properties for Medical Uses.

The great demand for antibacterial, biocompatible, and easily manufactured nanostructures has led to the design and development of graphene-wrapped copper nanoparticles (CuNPs) supported on Si wafers. In this study, we investigated the antibacterial properties of graphene/CuNPs nanostructures against Gram-positive and Gram-negative bacteria. Additional experiments regarding graphene/CuNPs nanostructures behavior against mouse fibroblast cell line L929 indicated their biocompatibility and consequently render them as model biomaterials for medical uses. Biofunctionalization of graphene/CuNPs nanostructures with a high-molecular-weight protein (green fluorescent protein), which retains its functionality after a "tight binding" on the nanostructure's surface, opens the way for attaching and other proteins, or biomolecules of great biological interest, to prepare novel biomaterials.

Metal (Ag/Ti)-Containing Hydrogenated Amorphous Carbon Nanocomposite Films with Enhanced Nanoscratch Resistance: Hybrid PECVD/PVD System and Microstructural Characteristics.

This study aimed to develop hydrogenated amorphous carbon thin films with embedded metallic nanoparticles (a-C:H:Me) of controlled size and concentration. Towards this end, a novel hybrid deposition system is presented that uses a combination of Plasma Enhanced Chemical Vapor Deposition (PECVD) and Physical Vapor Deposition (PVD) technologies. The a-C:H matrix was deposited through the acceleration of carbon ions generated through a radio-frequency (RF) plasma source by cracking methane, whereas metallic nanoparticles were generated and deposited using terminated gas condensation (TGC) technology. The resulting material was a hydrogenated amorphous carbon film with controlled physical properties and evenly dispersed metallic nanoparticles (here Ag or Ti). The physical, chemical, morphological and mechanical characteristics of the films were investigated through X-ray reflectivity (XRR), Raman spectroscopy, Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM), Transmission Electron Microscopy (TEM) and nanoscratch testing. The resulting amorphous carbon metal nanocomposite films (a-C:H:Ag and a-C:H:Ti) exhibited enhanced nanoscratch resistance (up to +50%) and low values of friction coefficient (<0.05), properties desirable for protective coatings and/or solid lubricant applications. The ability to form nanocomposite structures with tunable coating performance by potentially controlling the carbon bonding, hydrogen content, and the type/size/percent of metallic nanoparticles opens new avenues for a broad range of applications in which mechanical, physical, biological and/or combinatorial properties are required.

Remarkable Enhancement of the Hole Mobility in Several Organic Small-Molecules, Polymers, and Small-Molecule:Polymer Blend Transistors by Simple Admixing of the Lewis Acid p-Dopant B(C6F5)3.

Improving the charge carrier mobility of solution-processable organic semiconductors is critical for the development of advanced organic thin-film transistors and their application in the emerging sector of printed electronics. Here, a simple method is reported for enhancing the hole mobility in a wide range of organic semiconductors, including small-molecules, polymers, and small-molecule:polymer blends, with the latter systems exhibiting the highest mobility. The method is simple and relies on admixing of the molecular Lewis acid B(C6F5)3 in the semiconductor formulation prior to solution deposition. Two prototypical semiconductors where B(C6F5)3 is shown to have a remarkable impact are the blends of 2,8-difluoro-5,11-bis(triethylsilylethynyl)anthradithiophene:poly(triarylamine) (diF-TESADT:PTAA) and 2,7-dioctyl[1]-benzothieno[3,2-b][1]benzothiophene:poly(indacenodithiophene-co-benzothiadiazole) (C8-BTBT:C16-IDTBT), for which hole mobilities of 8 and 11 cm2 V-1 s-1, respectively, are obtained. Doping of the 6,13-bis(triisopropylsilylethynyl)pentacene:PTAA blend with B(C6F5)3 is also shown to increase the maximum hole mobility to 3.7 cm2 V-1 s-1. Analysis of the single and multicomponent materials reveals that B(C6F5)3 plays a dual role, first acting as an efficient p-dopant, and secondly as a microstructure modifier. Semiconductors that undergo simultaneous p-doping and dopant-induced long-range crystallization are found to consistently outperform transistors based on the pristine materials. Our work underscores Lewis acid doping as a generic strategy towards high performance printed organic microelectronics.

Heterojunction oxide thin-film transistors with unprecedented electron mobility grown from solution.

Thin-film transistors made of solution-processed metal oxide semiconductors hold great promise for application in the emerging sector of large-area electronics. However, further advancement of the technology is hindered by limitations associated with the extrinsic electron transport properties of the often defect-prone oxides. We overcome this limitation by replacing the single-layer semiconductor channel with a low-dimensional, solution-grown In2O3/ZnO heterojunction. We find that In2O3/ZnO transistors exhibit band-like electron transport, with mobility values significantly higher than single-layer In2O3 and ZnO devices by a factor of 2 to 100. This marked improvement is shown to originate from the presence of free electrons confined on the plane of the atomically sharp heterointerface induced by the large conduction band offset between In2O3 and ZnO. Our finding underscores engineering of solution-grown metal oxide heterointerfaces as an alternative strategy to thin-film transistor development and has the potential for widespread technological applications.

Chiral Metal-Oxide Nanofilms by Cellulose Template Using Atomic Layer Deposition Process.

In this article, we describe an advance approach for the fabrication of chiral metal-oxide nanofilms. Our approach is based on the atomic layer deposition of titania and alumina nanofilms onto cellulose microfibers, used as chiral templates, leading to the formation of chiral nanofilms with a spatial fibrous structure. The chiral nanofilms were extensively characterized by X-ray photoelectron spectroscopy and high-resolution electron microscopy. The chiral property of the produced titania nanofilms was studied by enantioselective adsorption experiments using circular-dichroism spectroscopy and chiral high-performance liquid chromatography. We demonstrate the application of the titania chiral nanofilms for enantioselective crystallization. Overall, the basic principle for the preparation of chiral nanofilms by atomic layer deposition is demonstrated, as well as their uses for several enantioselective applications.

Small Molecule/Polymer Blend Organic Transistors with Hole Mobility Exceeding 13 cm(2) V(-1) s(-1).

A ternary organic semiconducting blend composed of a small-molecule, a conjugated polymer, and a molecular p-dopant is developed and used in solution-processed organic transistors with hole mobility exceeding 13 cm(2) V(-1) s(-1) (see the Figure). It is shown that key to this development is the incorporation of the p-dopant and the formation of a vertically phase-separated film microstructure.

Selective modification of nanoparticle arrays by laser-induced self assembly (MONA-LISA): putting control into bottom-up plasmonic nanostructuring.

Nano-structuring of metals is one of the greatest challenges for the future of plasmonic and photonic devices. Such a technological challenge calls for the development of ultra-fast, high-throughput and low-cost fabrication techniques. Laser processing, accounts for the aforementioned properties, representing an unrivalled tool towards the anticipated arrival of modules based in metallic nanostructures, with an extra advantage: the ease of scalability. In the present work we take advantage of the ability to tune the laser wavelength to either match the absorption spectral profile of the metal or to be resonant with the plasma oscillation frequency, and demonstrate the utilization of different optical absorption mechanisms that are size-selective and enable the fabrication of pre-determined patterns of metal nanostructures. Thus, we overcome the greatest challenge of Laser Induced Self Assembly by combining simultaneously large-scale character with atomic-scale precision. The proposed process can serve as a platform that will stimulate further progress towards the engineering of plasmonic devices.

High acoustic strains in Si through ultrafast laser excitation of Ti thin-film transducers.

The role of thin-film metal transducers in ultrafast laser-generated longitudinal acoustic phonons in Si (100) monocrystal substrates is investigated. For this purpose degenerate femtosecond pump-probe transient reflectivity measurements are performed probing the Brillouin scattering of laser photons from phonons. The influence of the metallic electron-phonon coupling factor, acoustical impedance and film thickness is examined. An optical transfer matrix method for thin films is applied to extract the net acoustic strain relative strength for the various transducer cases, taking into account the experimental probing efficiency. In addition, a theoretical thermo-mechanical approach based on the combination of a revised two-temperature model and elasticity theory is applied and supports the experimental findings. The results show highly efficient generation of acoustic phonons in Si when Ti transducers are used. This demonstrates the crucial role of the transducer's high electron-phonon coupling constant and high compressive yield strength, as well as strong acoustical impedance matching with the semiconductor substrate.

Indium oxide thin-film transistors processed at low temperature via ultrasonic spray pyrolysis.

The use of ultrasonic spray pyrolysis is demonstrated for the growth of polycrystalline, highly uniform indium oxide films at temperatures in the range of 200-300 °C in air using an aqueous In(NO3)3 precursor solution. Electrical characterization of as-deposited films by field-effect measurements reveals a strong dependence of the electron mobility on deposition temperature. Transistors fabricated at ∼250 °C exhibit optimum performance with maximum electron mobility values in the range of 15-20 cm(2) V (-1) s(-1) and current on/off ratio in excess of 10(6). Structural and compositional analysis of as-grown films by means of X-ray diffraction, diffuse scattering, and X-ray photoelectron spectroscopy reveal that layers deposited at 250 °C are denser and contain a reduced amount of hydroxyl groups as compared to films grown at either lower or higher temperatures. Microstructural analysis of semiconducting films deposited at 250 °C by high resolution cross-sectional transmission electron microscopy reveals that as-grown layers are extremely thin (∼7 nm) and composed of laterally large (30-60 nm) highly crystalline In2O3 domains. These unique characteristics of the In2O3 films are believed to be responsible for the high electron mobilities obtained from transistors fabricated at 250 °C. Our work demonstrates the ability to grow high quality low-dimensional In2O3 films and devices via ultrasonic spray pyrolysis over large area substrates while at the same time it provides guidelines for further material and device improvements.

Nanocomposite catalysts producing durable, super-black carbon nanotube systems: applications in solar thermal harvesting.

A novel two-step approach for preparing carbon nanotube (CNT) systems, exhibiting an extraordinary combination of functional properties, is presented. It is based upon nanocomposite films consisting of metal (Me = Ni, Fe, Mo, Sn) nanoparticles embedded into diamond-like carbon (DLC). The main concept behind this approach is that DLC inhibits the growth of Me, resulting in the formation of small nanospheres instead of layers or extended grains. In the second step, DLC:Me substrates were used as catalyst templates for the growth of CNTs by the thermal chemical vapor deposition (T-CVD) process. X-ray photoelectron spectroscopy (XPS) has shown that at the T-CVD temperature of 700 °C DLC is completely graphitized and NiC is formed, making DLC:Ni a very effective catalyst for CNT growth. The catalyst layers and the CNT systems have been characterized with a wide range of analytical techniques such as Auger electron spectroscopy and X-ray photoelectron spectroscopy (AES/XPS), X-ray diffraction, reflectivity and scattering, Raman spectroscopy, scanning electron microscopy, atomic force microscopy, and optical and electrical testing. The produced CNTs are of excellent quality, without needing any further purification, durable, firmly attached to the substrate, and of varying morphology depending on the density of catalyst nanoparticles. The produced CNTs exhibit exceptional properties, such as super-hydrophobic surfaces (contact angle up to 165°) and exceptionally low optical reflection (reflectivity <10(-4)) in the entirety of the visible range. The combination of the functional properties makes these CNT systems promising candidates for solar thermal harvesting, as it is demonstrated by solar simulation experiments.

Bare-eye view at the nanoscale: new visual interferometric multi-indicator (VIMI).

By exploiting the interferometric antireflection action of a probe sample, consisting of a diamond-like carbon (DLC) film grown on Si, combined with a specific illumination spectrum, we designed and constructed an optical device for the visual remote sensing of radiation (either plasma or atomic oxygen) and for the visual inspection of adsorbed organic contamination as thin as a few molecular layers. The capabilities of this new visual interferometric multi-indicator (VIMI) enable the bare-eye color detection of thickness changes on the order of a few nanometers without the intervention of any instrumental or computer interface.