A multicenter study of modified electron beam output calibration.

PURPOSE: This study aims to assess the accuracy of a modified electron beam calibration based on the IAEA TRS-398 and AAPM-TG-51 in multicenter radiotherapy. METHODS: This study was performed using the Elekta and Varian Linear Accelerator electron beams with energies of 4-22 MeV under reference conditions using cylindrical (PTW 30013, IBA FC65-G, and IBA FC65-P) and parallel-plate (PTW 34045, PTW 34001, and IBA PPC-40) chambers. The modified calibration used a cylindrical chamber and an updated k ' Q $k{^{\prime}}_Q$ based on Monte Carlo calculations, whereas TRS-398 and TG-51 used cylindrical and parallel-plate chambers for reference dosimetry. The dose ratio of the modified calibration procedure, TRS-398 and TG-51 were obtained by comparing the dose at the maximum depth of the modified calibration to TRS-398 and TG-51. RESULTS: The study found that all cylindrical chambers' beam quality conversion factors determined with the modified calibration ( k ' Q ) $( {{{k^{\prime}}}_Q} )$ to the TRS-398 and TG-51 vary from 0.994 to 1.003 and 1.000 to 1.010, respectively. The dose ratio of modified/TRS-398cyl and modified/TRS-398parallel-plate, the variation ranges were 0.980-1.014 and 0.981-1.019, while for the counterpart modified/TG-51cyl was found varying between 0.991 and 1.017 and the ratio of modified/TG-51parallel-plate varied in the range of 0.981-1.019. CONCLUSION: This multi-institutional study analyzed a modified calibration procedure utilizing new data for electron beam calibrations at multiple institutions and evaluated existing calibration protocols. Based on observed variations, the current calibration protocols should be updated with detailed metrics on the stability of linac components.

Analysis of dose distribution reproducibility based on a fluence map of in vivo transit dose using an electronic portal imaging device.

Morphological changes can affect distribution of dose in patients. Determination of the dose distribution changes for each fraction radiotherapy can be done by relativein vivodosimetry (IVD). This study analysed the distribution of doses per fraction based on the fluence map recorded by the electronic portal imaging device (EPID) of the patient's transit dose. This research examined cases involving the cervix, breast, and nasopharynx. Transit dose analysis was performed by calculating the gamma index (GI) with composite and field-by-field methods. The gamma passing rate (GPR) value was assessed for its correlation with the subject's body weight. In the case of the nasopharynx, breast, and cervix, the GPR value decreased as the fraction increased. In the case of the nasopharynx, the correlation between the GPR and fraction radiotherapy showed no difference when using either composite or field-by-field methods. However, in cases involving the cervix and breast, there was a difference in the correlation values between the composite and field-by-field methods, where the subject had a significant correlation (p< 0.05) when it was done using a field-by-field method. In addition, the nasopharynx had the highest number of subjects with significant correlation (p< 0.05) between GPR and body weight, followed by the cervix and breast. In the nasopharynx, breast, and cervix, the reproducibility of the dose distribution decreased. This decreased reproducibility was associated with changes in body weight.

Modified calibration protocols in electron beam dosimetry: comparison with IAEA TRS-398 and AAPM TG-51.

This study aimed to compare absolute calibration outputs based on the protocols of the International Atomic Energy Agency (IAEA) Technical Report Series (TRS)-398, the American Association of Physicists in Medicine (AAPM) Task Group (TG)-51, and modified calibration approach. The electron beam output calibration followed the IAEA TRS-398 and AAPM TG-51 protocols, both of which required cylindrical chambers and parallel plates. However, the use of cylindrical chambers is not recommended at low energies because of the large fluence-correction factor. TG-51 recommended cross-calibration of the parallel-plate chamber against the cylindrical chamber in a high-energy electron beam. In 2020, an electron beam dosimetry modification was introduced that used a cylindrical ionisation chamber at all energies and updated the data for beam quality conversion factors. This modification provided a lower deviation than that reported in AAPM TG-51. Thus, the modified calibration based on TRS-398 was applied in the present study, which yielded results below the permissible tolerance. The beam calibration at 6, 8, 10, 12, and 15 MeV energies was carried out for two Elekta linear accelerators.. Electron beam dosimetry followed the AAPM TG-51 and TRS-398 protocols, and modified calibration were performed to measure the dose at the maximum depth expressed in dose/monitor units (cGy/MU). Charge-reading measurements were measured using ionisation chambers PTW 30013, IBA CC13, and Exradin A11. The average absorbed dose ratios were 1.004 and 1.009 using the modified calibration and TRS-398 and modified calibration and TG-51, respectively. Therefore, based on IAEA TRS-398, the results were below the tolerance limit (±2%).

Failure modes and downtime of radiotherapy LINACs and multileaf collimators in Indonesia.

BACKGROUND AND PURPOSE: The lack of equitable access to radiotherapy (RA) linear accelerators (LINACs) is a substantial barrier to cancer care in low- and middle-income countries (LMICs). These nations are expected to bear up to 75% of cancer-related deaths globally by 2030. State-of-the-art LINACs in LMICs experience major issues in terms of robustness, with mechanical and electrical breakdowns resulting in downtimes ranging from days to months. While existing research has identified the higher failure frequency and downtimes between LMICs (Nigeria, Botswana) compared to high-income countries (HICs, the UK), there has been a need for additional data and study particularly relating to multileaf collimators (MLCs). MATERIALS AND METHODS: This study presents for the first time the analysis of data gathered through a dedicated survey and workshop including participants from 14 Indonesian hospitals, representing a total of 19 LINACs. We show the pathways to failure of radiotherapy LINACs and frequency of breakdowns with a focus on the MLC subsystem. RESULTS: This dataset shows that LINACs throughout Indonesia are out of operation for seven times longer than HICs, and the mean time between failures of a LINAC in Indonesia is 341.58 h or about 14 days. Furthermore, of the LINACs with an MLC fitted, 59 . 02 - 1.61 + 1.98 $59.02_{ - 1.61}^{ + 1.98}$ % of all mechanical faults are due to the MLC, and 57 . 14 - 1.27 + 0.78 $57.14_{ - 1.27}^{ + 0.78}$ % of cases requiring a replacement component are related to the MLC. CONCLUSION: These results highlight the pressing need to improve robustness of RT technology for use in LMICs, highlighting the MLC as a particularly problematic component. This work motivates a reassessment of the current generation of RT LINACs and demonstrates the need for dedicated efforts toward a future where cancer treatment technology is robust for use in all environments where it is needed.

Comparison of deep learning models for building two-dimensional non-transit EPID Dosimetry on Varian Halcyon.

Background: This study compared the effectiveness of five deep learning models in constructing non-transit dosimetry with an a-Si electronic portal imaging device (EPID) on Varian Halcyon. Deep learning model is increasingly used to support prediction and decision-making in several fields including oncology and radiotherapy. Materials and methods: Forty-seven unique plans of data obtained from breast cancer patients were calculated using Eclipse treatment planning system (TPS) and extracted from DICOM format as the ground truth. Varian Halcyon was then used to irradiate the a-Si 1200 EPID detector without an attenuator. The EPID and TPS images were augmented and divided randomly into two groups of equal sizes to distinguish the validation and training-test data. Five different deep learning models were then created and validated using a gamma index of 3%/3 mm. Results: Four models successfully improved the similarity of the EPID images and the TPS-generated planned dose images. Meanwhile, the mismatch of the constituent components and number of parameters could cause the models to produce wrong results. The average gamma pass rates were 90.07 ± 4.96% for A-model, 77.42 ± 7.18% for B-model, 79.60 ± 6.56% for C-model, 80.21 ± 5.88% for D-model, and 80.47 ± 5.98% for E-model. Conclusion: The deep learning model is proven to run fast and can increase the similarity of EPID images with TPS images to build non-transit dosimetry. However, more cases are needed to validate this model before being used in clinical activities.

Evaluation of target volume and dose accuracy in intrafractional cases of lung cancer based on 4D-CT and 4D-CBCT images using an in-house dynamic thorax phantom.

Background: This study aimed to evaluate the target volume and dose accuracy in intrafraction cases using 4-dimensional imaging modalities and an in-house dynamic thorax phantom. Intrafraction motion can create errors in the definition of target volumes, which can significantly affect the accuracy of radiation delivery. Motion management using 4-dimensional modalities is required to reduce the risk. Materials and methods: Two variations in both breathing amplitude and target size were applied in this study. From these variations, internal target volume (ITVs) contoured in 10 phases of 4D-CT (ITV10), average intensity projection (AIP), and mid-ventilation (Mid-V) images were reconstructed from all 4D-CT datasets as reference images. Free-breathing (FB), augmentation free-breathing (Aug-FB), and static images were also acquired using the 3D-CT protocol for comparisons. In dose evaluations, the 4D-CBCT modality was applied before irradiation to obtain position correction. Then, the dose was evaluated with Gafchromic film EBT3. Results: The ITV10, AIP, and Mid-V provide GTVs that match the static GTV. The AIP and Mid-V reference images allowed reductions in ITVs and PTVs without reducing the range of target movement areas compared to FB and Aug-FB images with varying percentages in the range of 29.17% to 48.70%. In the dose evaluation, the largest discrepancies between the measured and planned doses were 10.39% for the FB images and 9.21% for the Aug-FB images. Conclusion: The 4D-CT modality can enable accurate definition of the target volume and reduce the PTV. Furthermore, 4D-CBCT provides localization images during registration to facilitate position correction and accurate dose delivery.

2-Dimensional IMRT dose audit: An Indonesian multicenter study.

Intensity modulated radiation therapy (IMRT) is an advanced technique in radiation therapy delivery. IMRT depends on the accuracy of the multileaf collimator during treatment. Hence, the actual dose distribution can deviate from the treatment planning system's calculation. This study aimed to perform a multicentre planar dosimetry audit of radiotherapy centres in Indonesia, using the structure sets from AAPM TG-119. The gamma index used to evaluate the dose distribution was 3%/3 mm and 3%/2 mm. We observed 100% gamma index passing rates mostly in the 3%/3 mm evaluations. The gamma index passing rates dropped in the 3%/2 mm analysis. Most of the radiotherapy centres participating in this audit satisfied each criterion's tolerance limit of the action level. This study may become a first result for the next multicenter IMRT audit by using a standardized protocol.

Modified electron beam output calibration based on IAEA Technical Report Series 398.

PURPOSE: The recently worldwide standard measurement of electron beam reference dosimetry include the International Atomic Energy Agency (IAEA) Technical Report Series (TRS)-398 and Association of Physicists in Medicine (AAPM) Task Group (TG)-51 protocols. Muir et al. have modified calibration methods for electron beam calibration based on AAPM TG-51. They found that the use of cylindrical chambers at low energy gave acceptable results. In this study, we propose and report a modified calibration for electron beam based on IAEA TRS-398, the standard reference dosimetry protocol worldwide. METHODS: This work was carried out with energies of 6, 8, 10, 12, and 15 MeV. The electron beam is generated from Elektra Synergy Platform and Versa HD linear accelerator. The charge readings were measured with PTW 30013, IBA CC13, Exradin A1Sl, and Exradin A11 chambers connected to the electrometer. The dose calculation uses an equation of modified calibration for electron beam using the updated k Q ${k_Q}$ factor in previous work. The absorbed dose to water for electron beam is expressed in dose per monitor unit (cGy/MU). Thus, we compared dose per monitor unit (D/MU) calculation using a modified calibration to TRS-398. RESULTS: In this work, we have succeeded in implementing the modified calibration of electron beam based on TRS-398 by applying a cylindrical chamber in all energy beams and using the updated k Q ${k_Q}$ factor. The ratio of the absorbed dose to water between original and modified calibration protocols of TRS-398 (Dw ) for the cylindrical chamber was 1.002 on the Elekta Synergy Platform and 1.000 on the Versa HD while for the parallel-plate chamber it was 1.013 on the Elekta Synergy Platform and 1.014 on the Versa HD. Based on these results, both the cylindrical and parallel-plate chambers are still within the tolerance limit allowed by the TRS-398 protocol, which is ±2%. Therefore, modified calibration based on TRS-398 gives acceptable results and is simpler to use clinically.

Evaluation of the linac neutron dose profile for various depths and field sizes: a Monte Carlo study.

High-energy medical linear accelerator (Linac) has been widely used for treating cancer patients. However, with its effectiveness, high-energy linac yields an undesirable amount of neutron contamination. An MCNPX code version 2.6.0 was used for calculating photoneutron contamination from Varian Clinac iX 15 MV linac heads in this study. The fast neutrons were dominantly produced inside the linac head. The neutron fluence, absorbed dose, and dose equivalent calculations occurred inside a linac head and a water phantom model. The fast neutrons begin to be moderated after 1 cm inside the water phantom by calculating the energy spectra. Variations in the field sizes from 2 × 2, 5 × 5, 10 × 10, and 15 × 15 cm2show that the neutron production yield would increase for larger field sizes. The maximum neutron dose equivalents are 3.745; 7.687; 11.794 and 14.197µSv/MU for 2 × 2, 5 × 5, 10 × 10 and 15 × 15 cm2field sizes, respectively. These calculations predict the photoneutron characteristics with more detail inside a treated patient during radiation therapy procedures.

Optimization of dose and image quality of paediatric cardiac catheterization procedure.

The purpose of this study is to quantify the quality of the available imaging modes for various iodine-based contrast agent concentration in paediatric cardiology. The figure of merit (FOM) was defined as the squared signal to noise ratio divided by a patient dose related parameter. An in house constructed phantom simulated a series of vessel segments with iodine concentrations from 10% or 30 mg/cc to 16% or 48 mg/cc of iodine in a blood plasma solution, all within the dimensional constraints of a paediatric patient. The phantom also used test inserts of tin (Sn). Measurements of Entrance Surface Air Kerma (ESAK) and exit dose rate were performed along with calculations of the signal-to-noise ratio (SNR) of all the objects. A first result showed that it was favourable to employ low dose fluoroscopy mode and lower frame rate modes in cine acquisition if dynamic information is not critical. Normal fluoroscopy dose mode provided a considerably higher dose level (in comparison to low dose mode) with only a slight improvement in SNR. Higher frame rate cine modes should be used however when the clinical situation dictates so. This work also found that tin should not be intended as iodine replacement material for research purposes due to the mismatching SNR, particularly on small vessel sizes.

Monitoring tumor motion by real time 2D/3D registration during radiotherapy.

BACKGROUND AND PURPOSE: In this paper, we investigate the possibility to use X-ray based real time 2D/3D registration for non-invasive tumor motion monitoring during radiotherapy. MATERIALS AND METHODS: The 2D/3D registration scheme is implemented using general purpose computation on graphics hardware (GPGPU) programming techniques and several algorithmic refinements in the registration process. Validation is conducted off-line using a phantom and five clinical patient data sets. The registration is performed on a region of interest (ROI) centered around the planned target volume (PTV). RESULTS: The phantom motion is measured with an rms error of 2.56 mm. For the patient data sets, a sinusoidal movement that clearly correlates to the breathing cycle is shown. Videos show a good match between X-ray and digitally reconstructed radiographs (DRR) displacement. Mean registration time is 0.5 s. CONCLUSIONS: We have demonstrated that real-time organ motion monitoring using image based markerless registration is feasible.

High-performance GPU-based rendering for real-time, rigid 2D/3D-image registration and motion prediction in radiation oncology.

A common problem in image-guided radiation therapy (IGRT) of lung cancer as well as other malignant diseases is the compensation of periodic and aperiodic motion during dose delivery. Modern systems for image-guided radiation oncology allow for the acquisition of cone-beam computed tomography data in the treatment room as well as the acquisition of planar radiographs during the treatment. A mid-term research goal is the compensation of tumor target volume motion by 2D/3D Registration. In 2D/3D registration, spatial information on organ location is derived by an iterative comparison of perspective volume renderings, so-called digitally rendered radiographs (DRR) from computed tomography volume data, and planar reference x-rays. Currently, this rendering process is very time consuming, and real-time registration, which should at least provide data on organ position in less than a second, has not come into existence. We present two GPU-based rendering algorithms which generate a DRR of 512×512 pixels size from a CT dataset of 53 MB size at a pace of almost 100 Hz. This rendering rate is feasible by applying a number of algorithmic simplifications which range from alternative volume-driven rendering approaches - namely so-called wobbled splatting - to sub-sampling of the DRR-image by means of specialized raycasting techniques. Furthermore, general purpose graphics processing unit (GPGPU) programming paradigms were consequently utilized. Rendering quality and performance as well as the influence on the quality and performance of the overall registration process were measured and analyzed in detail. The results show that both methods are competitive and pave the way for fast motion compensation by rigid and possibly even non-rigid 2D/3D registration and, beyond that, adaptive filtering of motion models in IGRT.

Validation for 2D/3D registration. II: The comparison of intensity- and gradient-based merit functions using a new gold standard data set.

PURPOSE: A new gold standard data set for validation of 2D/3D registration based on a porcine cadaver head with attached fiducial markers was presented in the first part of this article. The advantage of this new phantom is the large amount of soft tissue, which simulates realistic conditions for registration. This article tests the performance of intensity- and gradient-based algorithms for 2D/3D registration using the new phantom data set. METHODS: Intensity-based methods with four merit functions, namely, cross correlation, rank correlation, correlation ratio, and mutual information (MI), and two gradient-based algorithms, the backprojection gradient-based (BGB) registration method and the reconstruction gradient-based (RGB) registration method, were compared. Four volumes consisting of CBCT with two fields of view, 64 slice multidetector CT, and magnetic resonance-T1 weighted images were registered to a pair of kV x-ray images and a pair of MV images. A standardized evaluation methodology was employed. Targets were evenly spread over the volumes and 250 starting positions of the 3D volumes with initial displacements of up to 25 mm from the gold standard position were calculated. After the registration, the displacement from the gold standard was retrieved and the root mean square (RMS), mean, and standard deviation mean target registration errors (mTREs) over 250 registrations were derived. Additionally, the following merit properties were computed: Accuracy, capture range, number of minima, risk of nonconvergence, and distinctiveness of optimum for better comparison of the robustness of each merit. RESULTS: Among the merit functions used for the intensity-based method, MI reached the best accuracy with an RMS mTRE down to 1.30 mm. Furthermore, it was the only merit function that could accurately register the CT to the kV x rays with the presence of tissue deformation. As for the gradient-based methods, BGB and RGB methods achieved subvoxel accuracy (RMS mTRE down to 0.56 and 0.70 mm, respectively). Overall, gradient-based similarity measures were found to be substantially more accurate than intensity-based methods and could cope with soft tissue deformation and enabled also accurate registrations of the MR-T1 volume to the kV x-ray image. CONCLUSIONS: In this article, the authors demonstrate the usefulness of a new phantom image data set for the evaluation of 2D/3D registration methods, which featured soft tissue deformation. The author's evaluation shows that gradient-based methods are more accurate than intensity-based methods, especially when soft tissue deformation is present. However, the current nonoptimized implementations make them prohibitively slow for practical applications. On the other hand, the speed of the intensity-based method renders these more suitable for clinical use, while the accuracy is still competitive.