Desorption of Polycyclic Aromatic Hydrocarbons from Microplastics in Human Gastrointestinal Fluid Simulants-Implications for Exposure Assessment.

Microplastics have been detected in various food types, suggesting inevitable human exposure. A major fraction may originate from aerial deposition and could be contaminated by ubiquitous pollutants such as polycyclic aromatic hydrocarbons (PAHs). While data on the sorption of pollutants to microplastics are abundant, the subsequent desorption in the gastrointestinal tract (GIT) is less understood. This prompted us to systematically investigate the release of microplastics-sorbed PAHs at realistic loadings (44-95 ng/mg) utilizing a physiology-based in vitro model comprising digestion in simulated saliva, gastric, and small and large intestinal fluids. Using benzo[a]pyrene as a representative PAH, desorption from different microplastics based on low density polyethylene (LDPE), thermoplastic polyurethanes (TPUs), and polyamides (PAs) was investigated consecutively in all four GIT fluid simulants. The cumulative relative desorption (CRD) of benzo[a]pyrene was negligible in saliva simulant but increased from gastric (4 ± 1% - 15 ± 4%) to large intestinal fluid simulant (21 ± 1% - 29 ± 6%), depending on the polymer type. CRDs were comparable for ten different microplastics in the small intestinal fluid simulant, except for a polydisperse PA-6 variant (1-10 µm), which showed an exceptionally high release (51 ± 8%). Nevertheless, the estimated contribution of microplastics-sorbed PAHs to total human PAH dietary intake was very low (≤0.1%). Our study provides a systematic data set on the desorption of PAHs from microplastics in GIT fluid simulants.

The power of centrifugation: How to extract microplastics from soil with high recovery and matrix removal efficiency.

Understanding the occurrence and transformation of microplastics when released into the environment is essential for risk assessment. The use of biodegradable polymers in agriculture can help to reduce microplastic accumulation in soil, since released fragments of such materials are not persistent and are further transformed into CO2 and biomass (Wohlleben et al., 2023). To be able to monitor the fragmentation and biodegradation of these materials in soil, a validated extraction protocol is needed, which does not induce changes in the chemical and particle properties, additionally it should show high recoveries and matrix removal efficiency. A density-based extraction method in the centrifuge has the potential to remove a high amount of the soil matrix and is very selective for the polymer at the same time. Here we developed an efficient and non-destructive extraction protocol for biodegradable fragments from different soils using sequential centrifugation steps with varying densities and a freezing approach for sample collection. Although the focus of the present study was on biodegradable fragments, the technique can also be used for other types of microplastics with similar or lower density than the one tested for the method validation, but additional recovery tests for the target analyte are recommended.•A density-based extraction method for microplastics from soil, validated by recovery and stability tests using biodegradable polymers•Vessel changes and harsh chemical treatments are kept to a minimum.

An innovative microplastic extraction technique: The switchable calcium chloride density separation column tested for biodegradable polymers, polyethylene, and polyamide.

Extracting microplastics from complex matrices poses challenges due to the potential impact of harsh chemical treatments on microplastic properties. For fate and hazard assessment reliable techniques are needed to not only quantify the particle number but also to assess the physicochemical properties of environmental microplastics with minimum changes induced by extraction. Here we present the method development for an innovative and non-destructive extraction protocol based on a switchable calcium chloride density separation column. In contrast to commonly reported extraction protocols, the presented technique is suitable for targeted microplastic property analysis (e.g., surface chemistry and texture) by keeping chemical treatments (such as oxidation and enzymatic digestion) to a minimum. By adjusting the temperature we can control the aggregate state of the highly concentrated salt solution, allowing to separate the microplastics from matrix by cutting of purified, solidified samples. Harsh chemical treatments are avoided, as well as obstruction of microplastic extraction by adsorption to matrix components when passing the tap at the bottom of traditional density separation funnels. The use of microplastics that were prelabeled with a fluorescence dye helped to solve difficulties observed during method development by visual inspection before measurement of extraction efficiency: We spiked a blank compost with low-density polyethylene (LDPE) and polyamide (PA). Additionally, UV aged LDPE was used to demonstrate applicability to more hydrophilic, more environmentally relevant microplastics. The obtained initial results show high recovery of both unaged and aged LDPE over 97 wt.-% and an efficient compost removal but a lower and less robust recovery (between 68 and 18 wt.-%) for PA particles that are more challenging to extract due to an unfortunate synergistic combination of smaller particle size and higher density. Method adaptation to other microplastic types may still be necessary. In short:•A low-cost and simple approach without oxidation to extract (pre-aged) microplastics from compost•Method development by visual observation using fluorescent labelled microplastics and method validation by spike-recovery tests.

Effect of Polymer Properties on the Biodegradation of Polyurethane Microplastics.

The release of fragments from plastic products, that is, secondary microplastics, is a major concern in the context of the global plastic pollution. Currently available (thermoplastic) polyurethanes [(T)PU] are not biodegradable and therefore should be recycled. However, the ester bond in (T)PUs might be sufficiently hydrolysable to enable at least partial biodegradation of polyurethane particles. Here, we investigated biodegradation in compost of different types of (T)PU to gain insights into their fragmentation and biodegradation mechanisms. The studied (T)PUs varied regarding the chemistry of their polymer backbone (aromatic/aliphatic), hard phase content, cross-linking degree, and presence of a hydrolysis-stabilizing additive. We developed and validated an efficient and non-destructive polymer particle extraction process for partially biodegraded (T)PUs based on ultrasonication and density separation. Our results showed that biodegradation rates and extents decreased with increasing cross-linking density and hard-segment content. We found that the presence of a hydrolysis stabilizer reduced (T)PU fragmentation while not affecting the conversion of (T)PU carbon into CO2. We propose a biodegradation mechanism for (T)PUs that includes both mother particle shrinkage by surface erosion and fragmentation. The presented results help to understand structure-degradation relationships of (T)PUs and support recycling strategies.

Environmental Degradation of Microplastics: How to Measure Fragmentation Rates to Secondary Micro- and Nanoplastic Fragments and Dissociation into Dissolved Organics.

Understanding the environmental fate of microplastics is essential for their risk assessment. It is essential to differentiate size classes and degradation states. Still, insights into fragmentation and degradation mechanisms of primary and secondary microplastics into micro- and nanoplastic fragments and other degradation products are limited. Here, we present an adapted NanoRelease protocol for a UV-dose-dependent assessment and size-selective quantification of the release of micro- and nanoplastic fragments down to 10 nm and demonstrate its applicability for polyamide and thermoplastic polyurethanes. The tested cryo-milled polymers do not originate from actual consumer products but are handled in industry and are therefore representative of polydisperse microplastics occurring in the environment. The protocol is suitable for various types of microplastic polymers, and the measured rates can serve to parameterize mechanistic fragmentation models. We also found that primary microplastics matched the same ranking of weathering stability as their corresponding macroplastics and that dissolved organics constitute a major rate of microplastic mass loss. The results imply that previously formed micro- and nanoplastic fragments can further degrade into water-soluble organics with measurable rates that enable modeling approaches for all environmental compartments accessible to UV light.