Particle Shedding from Cotton and Cotton-Polyester Fabrics in the Dry State and in Washes.

The influence of 3, 10 and 50 washing cycles on the properties of cotton fabric and cotton-polyester blend in plain weave, was investigated in this study. In addition to the analysis of tensile properties in weft and warp directions and thickness, the number of particles produced in the dry state was also measured after 3, 10 and 50 washes. After washing, the entire effluent was analysed by determining the total suspended solids (TSS), the total solids (TS), the pH value and the conductivity. To determine the similarity of the observed wash cycles and properties of all processed samples, hierarchical cluster analysis (HCA) was performed. The fabric changes indicated by total wear in the warp direction after 50 washing cycles compared to unwashed ones amounting to 41.2% for cotton and 30.9% for cotton-polyester blend, may be attributed to the synergy of washing factors and raw material composition. Cotton fabric produced significantly more particles than cotton-polyester fabric in the dry state after the examined washing cycles in all size categories. A smaller number of released particles are in the larger size category >25 µm. The obtained TSS values confirm the degree of loading of the effluent with particulate matter from the analysed fabrics, since the detergent consists of water-soluble components. The HCA dendrograms confirmed that the release of particles during the first washing cycles is mainly determined by the structural properties of fabrics, while in the subsequent cycles the synergistic effect of chemical, mechanical and thermal effects in the interaction with the material prevailed.

Extending the Protection Ability and Life Cycle of Medical Masks through the Washing Process.

The reuse of decontaminated disposable medical face masks can contribute to reducing the environmental burden of discarded masks. This research is focused on the effect of household and laboratory washing at 50 °C on the quality and functionality of the nonwoven structure of polypropylene medical masks by varying the washing procedure, bath composition, disinfectant agent, and number of washing cycles as a basis for reusability. The barrier properties of the medical mask were analyzed before and after the first and fifth washing cycle indirectly by measuring the contact angle of the liquid droplets with the front and back surface of the mask, further by measuring air permeability and determining antimicrobial resistance. Additional analysis included FTIR, pH of the material surface and aqueous extract, as well as the determination of residual substances-surfactants-in the aqueous extract of washed versus unwashed medical masks, while their aesthetic aspect was examined by measuring their spectral characteristics. The results showed that household washing had a stronger impact on the change of some functional properties, primarily air permeability, than laboratory washing. The addition of the disinfectant agent, didecyldimethylammonium chloride, contributes to the protective ability and supports the idea that washing of medical masks under controlled conditions can preserve barrier properties and enable reusability.

Durability of Shield Effective Polyester Cotton Fabric with Integrated Stainless Steel Threads in Processes of Dry and Wet Cleaning.

Protective properties against electromagnetic radiation represent the essential value of textiles for protective clothing worn in hazardous working conditions. To ensure that protective clothing lasts for as long as feasible, care processes must be optimized, especially since protective clothing is subjected to repeated cycles due to soiling. Improved formulations of special detergents and agents with high-performance finishing agents used in care processes can contribute to a longer life of protective clothing. In this paper, the shield effectiveness of a cotton polyester fabric with integrated metal threads in the warp and weft directions at frequencies of 0.9 GHz, 1.8 GHz, 2.1 GHz, and 2.4 GHz is compared to that of its environmentally friendly alternative, wet cleaning processes. The research is carried out by varying process parameters: mechanics, chemical action, and cycle number. The results proved the drop of shield properties of polyester/cotton fabric with integrated stainless steel threads depending on frequencies and the number of professional cleaning cycles. The worst shield effectiveness of the tested fabric was obtained after 10 cycles of dry cleaning, wherein the degree of protection at frequency 2.4 GHz is reduced by 6.89 dB. According to the obtained results, the level of functional properties was better preserved in the wet cleaning process, which additionally has better ecological premises compared to dry cleaning process.

Impact of Washing Parameters on Thermal Characteristics and Appearance of Proban®-Flame Retardant Material.

Proban® is a multiphase treatment of cotton fabrics based on the formation of pre-condensates using the flame retardant (FR) agent tetrakis (hydroxymethyl) phosphonium salts (THPx). The assessment of the durability of a product demands a preliminary understanding of how relevant it is to extend its lifetime. It is therefore important to minimize the risk of agents impacting: (1) the protection level, (2) shape and dimensions, and (3) additional comfort characteristics of the fabric. This research focused on the impact of washing conditions on the durability of FR properties and appearance of Proban® cotton fabrics, which was systematically arranged through the variation in the chemistry distribution in the Sinner's circle. The chemical share was varied in laboratory conditions as a simulation of industrial washing based on component dosing, where the temperature, time and mechanical agitation were constant. The washing of cotton fabrics was performed through 10 cycles in four baths containing high alkali components, medium alkali components, high alkali reference detergent and water. The environmental acceptability of washing procedures through effluent analysis was assessed by physico-chemical and organic indicators. The limited oxygen index (LOI), calorimetric parameters (micro combustion calorimetry), thermal stability and evolved gases during thermal decomposition (thermogravimetric analyzer (TGA) coupled with an infrared spectrometer (TG-IR)), surface examination (FE-SEM), spectral characteristics and pH of the aqueous extract of the fabrics before and after 10 washing cycles were selected for proof of durability. The medium alkali bath was confirmed as a washing concept for Proban® cotton fabric through the preservation of FR properties examined through LOI, TGA, TG-IR and MCC parameters and appearance color and low level of fibrillation.

Biopolymer Textile Structure of Chitosan with Polyester.

The research deals with functionalization of a standard polyester fabric with biopolymer chitosan, whose premises are multifunctional and favour ecological effects. Due to the incompatibility of synthetic and natural polymers, the chitosan treatment was preceded by alkaline hydrolysis with sodium hydroxide with the addition of cationic and anionic surfactants as promoters. Compatibility of the chitosan with untreated and alkali-hydrolyzed fabrics was performed by analysis of mechanical and physico-chemical properties. The number of characterisation procedures performed required the use of hierarchical cluster analysis (HCA) to identify homogeneous groups or clusters in which similarities and differences between samples are visible. Almost all applied methods and evaluation parameters have shown that alkaline hydrolysis of polyester fabric has the best potential for functionalization with chitosan. Therefore, the addition of surfactants as promoters during alkaline hydrolysis is not necessary in the pretreatment process phase.

Reactive Printing and Wash Fastness of Inherent Flame Retardant Fabrics for Dual Use.

The possibility of reactive printability on protective flame-resistant fabrics, varied in composition of weft threads and weave was investigated. In addition, the wash fastness of printed samples was analyzed. The functional properties of fabrics were assessed by measuring of the Limiting Oxygen Index (LOI). Printing was performed with two printing pastes varied in thickeners and two dyestuff concentrations. The samples were analyzed by microscopic imaging using digital microscope and spectrophotometric measurement before and after the five washing cycles. The results confirmed the printability of FR inherent fabrics specified through fine colored effects and optimal wash fastness.

Electromagnetic Shielding Effectiveness of Woven Fabric with Integrated Conductive Threads after Washing with Liquid and Powder Detergents.

The paper investigates the shielding effectiveness of a newly developed cotton and polyester fabric into which conductive stainless-steel threads were incorporated in the warp and weft directions at frequencies 0.9 GHz, 1.8 GHz, 2.1 GHz, and 2.4 GHz. As resistance to external influences and degradation is an additional critical factor for protective textiles, the newly developed protective fabric was exposed to cumulative wash cycles with liquid and powder detergents, which were targeted to preserve the shielding effectiveness (SE). In addition to the SE shielding effectiveness, the influence of 10 washing cycles on the change in thickness as a structural parameter was analyzed. Micro-images of fabric surfaces before and after the first, third, fifth, seventh, and tenth washing cycles were also observed. The obtained results showed that powder and liquid detergents were well formulated to preserve the electromagnetic shielding effectiveness (EMSE) at higher frequencies. However, their impact on the appearance of the surface was not fully consistent with the shielding effectiveness.

Microplastics in Wastewater by Washing Polyester Fabrics.

Microplastics have become one of the most serious environmental hazards today, raising fears that concentrations will continue to rise even further in the near future. Micro/nanoparticles are formed when plastic breaks down into tiny fragments due to mechanical or photochemical processes. Microplastics are everywhere, and they have a strong tendency to interact with the ecosystem, putting biogenic fauna and flora at risk. Polyester (PET) and polyamide (PA) are two of the most important synthetic fibres, accounting for about 60% of the total world fibre production. Synthetic fabrics are now widely used for clothing, carpets, and a variety of other products. During the manufacturing or cleaning process, synthetic textiles have the potential to release microplastics into the environment. The focus of this paper is to explore the main potential sources of microplastic pollution in the environment, providing an overview of washable polyester materials.

Impact of Fabric Construction on Adsorption and Spreading of Liquid Contaminations.

A contamination on a textile material is defined as an undesirable, local formation that deviates in appearance from the rest of the material. In this paper the relationship between the shape and surface of liquid contaminations and the firmness factor of woven fabric is investigated. The interdependence of constructional and structural parameters of raw and bleached cotton fabrics were analysed. The results show that selected contaminations are distributed differently, primarily depending on the construction characteristics of the fabric, type of contamination and hydrophilicity of cotton fabric.

Particle Characterization of Washing Process Effluents by Laser Diffraction Technique.

The dominant type of polymer particles in water, sediment, and various organisms partly derives from natural and synthetic fibres released in the washing process. Pollution of aquatic recipients with these particles poses an interdisciplinary problem throughout the world. Wastewater from washing represents a dispersion system with different particle sizes that is also loaded with the source of the particles. Due to this complex system, the qualification and quantification of this type of pollution is difficult. In this paper, the laser diffraction technique was applied to characterize particles in effluents from washing and rinsing materials made of a mixture of cotton and polyester. The results obtained through the analysis prove that the laser diffraction technique is acceptable for the characterization of a composite effluent sample. The advanced statistical technique of multivariate analysis confirmed the interrelationship of the parameters of this complex dispersion system.

The Influence of Iron Ions on Optical Brighteners and Their Application to Cotton Fabrics.

The influence of iron ions at concentrations of 0.2, 0.5, and 1.0 g/L on optical brighteners of the groups stilbene and biphenyl in solution and on cotton fabric was investigated. Both groups of optical brighteners are intended for detergent formulations. The influence of iron ions was studied by absorption and fluorescence spectra in solution and by whiteness degree, identifying color differences using CIEL*a*b* coordinates and Ultraviolet Protection Factor (UPF) of cotton fabrics. The obtained results in solutions and cotton fabrics showed different behavior of optical brighteners stilbene and biphenyl in the presence of iron. Stilbene compounds with metal ions produced new species capable of absorbing in the UV-B region of the spectrum. A biphenyl compound in combination with iron had no effect on the absorption properties. Both optical brighteners were influenced by iron ions in the sense of fluorescence quenching. The influence of iron ions in single- and two-bath treatments of cotton fabrics after one cycle on whiteness degree and UPF was negligible.

Electromagnetic Shielding Properties of Knitted Fabric Made from Polyamide Threads Coated with Silver.

This paper investigates a textile material of low surface mass for its protection against electromagnetic radiation (EMR), which is suitable for composite structures of garments, and for technical and interior applications. The shielding effectiveness against EMR of fabric knitted from polyamide threads coated with silver, measured in the frequency range of 0.9 GHz to 2.4 GHz, indicated a high degree of protection. The key contribution of the paper is the evaluation of the stability of the shielding properties against EM radiation after applying apolar and polar solvents, in synergy with the cyclic process parameters of wet and dry cleaning. The results of the study confirmed the decline in the shielding effectiveness after successive cycles of material treatment with dry and wet cleaning. The effect of wet cleaning in relation to dry cleaning is more apparent, which is due to the damage of the silver coating on the polyamide threads in the knitted fabric.

Carboxymethyl Cellulose and Carboxymethyl Starch as Surface Modifiers and Greying Inhibitors in Washing of Cotton Fabrics.

This research is focused on cellulose and starch derivatives, carboxymethyl cellulose (CMC) and carboxymethyl starch (CMS), added to the detergent in washing reference cotton fabric in soft and hard water at 40, 60 and 90 °C. The applied polymers were analyzed through the potential of surface cellulose modification and inhibition of stain transfer from standard stain donors to modified and initial cotton fabrics. The surface modification of the cotton fabrics, characterized by the zeta potential and amounts of deposits, was coupled with the cluster analysis as well as a whiteness assessment. The obtained results of the zeta potential and degree of whiteness of the reference cotton fabrics before and after washing showed differences between CMC and CMS. The appropriateness of the cluster analysis was confirmed in assessing the potential of applied polymers for surface modification of cotton fabrics and greying inhibition.

Sigma-1 Receptor Expression in DRG Neurons During a Carrageenan-Provoked Inflammation.

Sigma 1 receptor (σ1R) is a non-opioid receptor that modulates pain perception and is strongly expressed in dorsal root ganglion (DRG) neurons. We studied the changes in the expression of σ1R in different sub-populations of DRG neurons during the first 48 hr in a carrageenan-induced inflammation rat model, with σ1R being a possible base for the development of neuropathic pain after inflammation. Twenty Sprague Dawley rats were divided into five groups (N = 4 in each group): the control (C) group was sacrificed immediately; all other animals received an intraplantar injection of 0.1 mL 2% carrageenan and were sacrificed in 6, 12, 24 or 48 hr after the injection and DRGs were collected and processed for immunohistochemistry. σ1R fluorescence intensity decreased slightly but significantly in up to 24 hr post-carrageenan injection in all sub-populations of DRG neurons (ib4+; ib4- medium, ib4- large and ib4- in total; P < 0.05 - P < 0.001), with the exception of the ib4- small neurons (<25 µm; P > 0.05). This decrement was followed by a subsequent increase in σ1R fluorescence intensity 48 hr after the plantar carrageenan injection (P < 0.05 - P < 0.0001). The same trend was also observed in the CGRP+ population of the DRG neurons, in the total population as well as in the CGRP+ small (<25 µm) and larger CGRP (>25 µm) sub-populations (P < 0.05 - P < 0.001). The presented results may contribute to further understanding of role of σ1R in the development of peripheral sensitization during inflammation. They may also be valuable for the therapeutic application of σ1R antagonists, particularly in the adjustment of the antagonist's dosage in a particular time window. Anat Rec, 302:1620-1627, 2019. © 2019 American Association for Anatomy.

Expression of Epithelial and Mesenchymal Differentiation Markers in the Early Human Gonadal Development.

Expressions of cytokeratin 8 (CK8), vimentin, nestin, and alpha-smooth-muscle-actin (alpha-SMA) were analyzed in the developing gonads of 12, 5-9 week old (W) human conceptuses by immunohistochemistry and immunofluorescence. During the investigated period, the number of CK8 positive cells increased from 56% to 92% in the gonadal surface epithelium, from 50% to 60% in the stroma, and from 23% to 42% in the medulla. In the early fetal period, the cell expression of CK8 increased in all gonadal parts, whereas primordial germ cells (PGC) remained negative. The expression of vimentin increased in the gonad stroma (gs) from 73% to 88%, and in the surface epithelium from 18% to 97% until ninth W. The medulla had the highest expression of vimentin in the seventh to eighth W (93%). Vimentin and CK8 colocalized in the somatic cells, while some PGCs showed vimentin expression only. Initially, nestin was positive in the gonad surface epithelium (8%) and stroma (52%), however during further development it decreased to 1% and 33%, respectively. In the early fetal period, the nestin positive cells decreased from 44% to 31% in the gonad medulla. Alpha-SMA was positive only in the blood vessels and mesonephros. The described pattern of expression of intermediate filaments (IF) in developing human gonads suggests their role in the control of PGC apoptosis, early differentiation of gs cells and cell migration. Both epithelial and mesenchymal origins of follicular cells and possible epithelial-to-mesenchymal transition of somatic cells is proposed. Lastly, IF intensity expression varies depending on the cell type and developmental period analyzed. Anat Rec, 300:1315-1326, 2017. © 2017 Wiley Periodicals, Inc.

Expression pattern of RAGE and IGF-1 in the human fetal ovary and ovarian serous carcinoma.

The expression pattern of RAGE and IGF-1 proteins in different ovarian cell lineages was histologically analyzed in six fetal, nine adult human ovaries, and nine serous ovarian carcinomas (OSC) using immunohistochemical methods. Mild expression of IGF-1 in ovarian surface epithelium (Ose) and oocytes in the 15-week human ovaries increased to moderate or strong in the stromal cells, oocytes and follicular cells in week 22. Occasional mild RAGE expression was observed in Ose during week 15, while strong expression characterized primordial follicles in week 22. In the reproductive human ovary, IGF-1 was mildly to moderately expressed in all ovarian cell lineages except in theca cells of the tertiary follicle where IGF-1 was negative. RAGE was strongly positive in the granulosa cells and some theca cells of the tertiary follicle, while negative to mildly positive in all cells of the secondary follicle. In the postmenopausal human ovary IGF-1 and RAGE were mildly expressed in Ose and stroma. In OSC, cells were strongly positive to IGF-1 and RAGE, except for some negative stromal cells. Different levels of IGF-1 and RAGE co-expression characterized fetal ovarian cells during development. In reproductive ovaries, IGF-1 and RAGE were co-localized in the granulosa and theca interna cells of tertiary follicles, while in postmenopausal ovaries and OSC, IGF-1 and RAGE were co-localized in Ose and OSC cells respectively. Our results indicate that intracellular levels of IGF-1 and RAGE protein might regulate the final destiny of the ovarian cell populations prior and during folliculogenesis, possibly controlling the metastatic potential of OSC as well.

The expression patterns of pro-apoptotic and anti-apoptotic factors in human fetal and adult ovary.

The influence of pro-apoptotic Bax and anti-apoptotic Bcl-2 proteins on the cell death (caspase-3, TUNEL) of different ovarian cell lineages was immunohistochemically analyzed in six fetal and five adult human ovaries in order to disclose possible mechanisms of cell number control. Mild to moderate expression of Bcl-2 characterized ovarian surface epithelium, follicular cells and oocytes of 15 and 22 week human ovaries, while expression of Bax and caspase-3 gradually increased in all ovarian cell populations, except caspase-3 in the ovarian surface epithelium. Different levels of Bax and Bcl-2 proteins co-expression characterized fetal ovarian cells, while TUNEL and caspase-3 co-expression was found only in some of them. In adult ovaries, Bcl-2 was moderately and Bax strongly expressed in the surface ovarian epithelium and stroma. Bcl-2 and Bax expression in granulosa and theca interna cells varied depending on the stage of follicular atresia. Caspase-3 apoptotic cells characterized granulosa cells of adult atretic follicles. Our results indicate that intracellular levels of Bcl-2 and Bax protein might regulate the final destiny of developing germ cells. Caspase-3 dependent apoptosis seems to be the most important, but not the only cell death pathway in ovaries. In adult ovaries, caspase-dependent cell death characterized granulosa cells, but not the germ cells.