Selective Detection of CO Using Proton-Conducting Graphene Oxide Membranes with Pt-Doped SnO2 Electrocatalysts: Mechanistic Study by Operando DRIFTS.

To reduce the risk of carbon monoxide (CO) poisoning, there is a strong need for small, compact gas sensors to detect and monitor CO at ppm concentrations. In this study, we focused on detecting CO with electrochemical sensors based on proton-conducting graphene oxide (GO) nanosheets at room temperature. We found that a Ce-doped GO nanosheet membrane fitted with the sensing electrode composed of Pt (10 wt %)-doped SnO2 nanocrystals exhibits an excellent sensor response to CO at 25 °C. Pt doping of SnO2 nanocrystals has made it possible to detect CO more selectively than H2 and ethanol. The CO detection mechanism is analyzed by operando diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), Fourier transform infrared gas cell measurements, and comprehensive density functional theory-based calculations. The results revealed that adsorption of CO occurs predominantly on Pt sites, and the adsorbed CO is anodically oxidized at the interface between the sensing electrode and proton-conducting membrane, generating the selective sensor response. The strong adsorption of CO was realized with Pt (10 wt %)-doped SnO2 nanocrystals, as revealed by the DRIFTS analysis and temperature-programed desorption technique.

Fast and selective production of quercetin and saccharides from rutin using microwave-assisted hydrothermal treatment in the presence of graphene oxide.

Rutin is a flavonoid glycoside, well-known for its antioxidant, anticarcinogenic, and cardioprotective properties. However, it exhibits lower bio absorptivity and bioactivity than its aglycon form, quercetin. Although liquid acid catalysts are conventionally utilized to obtain quercetin via rutin hydrolysis, the neutralization procedure is a major disadvantage owing to the added cost. In this study, graphene oxide (GO) was used as an alternative catalyst under microwave (MW) irradiation, owing to its easy separation from the reaction solution and high MW absorptivity, resulting in improved thermal efficiency. Two types of GOs were prepared (GO-HU using Hummer's method and GO-TO using Tour's method), and their catalytic performance for rutin hydrolysis was evaluated and compared. The highest rutin conversion (98.8 %) and quercetin yield (81.9 %) were obtained at 180 °C when the reaction was conducted for 15 min using 3 mg of GO-TO and 2400 ppm of initial rutin concentration in 50 mL of water.

A review on potential of green solvents in hydrothermal liquefaction (HTL) of lignin.

One of the greatest challenges in biorefinery is to reduce biomass' recalcitrance and enable valorization of lignin into higher value compounds. Likewise, green solvents and hydrothermal liquefaction (HTL) with feasible economic viability, functionality, and environmental sustainability have been widely introduced in extraction and conversion of lignin. This review starts with the underscore of disadvantages and limitations of conventional pretreatment approaches and role of green solvents in lignin extraction. Subsequently, the effect of process parameters along with the reaction mechanisms and kinetics on conversion of lignin through HTL were comprehensively reviewed. The limitations of green solvents in extraction and HTL of lignin from biomass were discussed based on the current advancements of the field and future research scopes were also proposed. More details info on HTL of biomass derived lignin which avoid the energy-intensive drying procedures are crucial for the accelerated development and deployment of the advanced lignin biorefinery.

Nano-pulsed discharge plasma-induced abiotic oligopeptide formation from diketopiperazine.

Conventional oligopeptide synthesis techniques involve environmentally harmful procedures and materials. In addition, the efficient accumulation of oligopeptides under Hadean Earth environments regarding the origin of life remains still unclear. In these processes, the formation of diketopiperazine is a big issue due to the strong inhibition for further elongation beyond dipeptides. Hydrothermal media enables environmentally friendly oligopeptide synthesis. However, hydrothermal oligopeptide synthesis produces large amounts of diketopiperazine (DKP), due to its thermodynamic stability. DKP inhibits dipeptide elongation and also constitutes an inhibitory pathway in conventional oligopeptide synthesis. Here, we show an efficient pathway for oligopeptide formation using a specially designed experimental setup to run both thermal and non-thermal discharge plasma, generated by nano-pulsed electric discharge with 16-23 kV voltage and 300-430 A current within ca. 500 ns. DKP (14%) was converted to dipeptides and higher oligopeptides in an aqueous solution containing alanine-DKP at pH 4.5, after 20 min of 50 pps thermal plasma irradiation. This is the first study to report efficient oligopeptide synthesis in aqueous medium using nano-pulsed plasma (with thermal plasma being more efficient than non-thermal plasma) via DKP ring-opening. This unexpected finding is implicative to evaluate the pathway how the oligopeptides could have accumulated in the primitive Earth with high-energy plasma sources such as thunder as well as to facilitate the green synthesis of oligopeptides.

Electrochemical Detection of Ethanol in Air Using Graphene Oxide Nanosheets Combined with Au-WO3.

Detection, monitoring, and analysis of ethanol are important in various fields such as health care, food industries, and safety control. In this study, we report that a solid electrolyte gas sensor based on a proton-conducting membrane is promising for detecting ethanol in air. We focused on graphene oxide (GO) as a new solid electrolyte because it shows a high proton conductivity at room temperature. GO nanosheets are synthesized by oxidation and exfoliation of expanded graphite via the Tour's method. GO membranes are fabricated by stacking GO nanosheets by vacuum filtration. To detect ethanol, Au-loaded WO3 is used as the sensing electrode due to the excellent activity of gold nanoparticles for the catalysis of organic molecules. Au-WO3 is coupled with rGO (reduced graphene oxide) to facilitate the electron transport in the electrode. Ce ions are intercalated into the GO membrane to facilitate proton transport. The sensor based on the Ce doped-GO membrane combined with Au-WO3/rGO as a sensing electrode shows good electric potential difference (ΔV) responses to ethanol in the air at room temperature. The sensor signal reaches more than 600 mV in response to ethanol at 40 ppm in air, making it possible to detect ethanol at a few ppb (parts per billion) level. The ethanol sensing mechanism was discussed in terms of the mixed-potential theory and catalysis of ethanol on Au-WO3.

Synergizing Sulfonated Hydrothermal Carbon and Microwave Irradiation for Intensified Esterification Reaction.

The synergy of sulfonated hydrothermal carbon and microwave (MW) irradiation was applied for the esterification of oleic acid with methanol (MeOH) to produce biodiesel. The effects of temperature, reaction time, ratio of oleic acid to methanol, and catalyst loading were investigated at a fixed MW power of 400 W. The addition of hexane, serving as a co-solvent and separator, was also investigated. The optimum conditions for the proposed process were oleic acid-to-methanol molar ratio of 1:5 and hexane-to-methanol ratio of 0.5 (v/v) in the presence of a 5 wt % catalyst, at 100 °C for 60 min, obtaining a 97% yield of oleic acid methyl ester. The addition of slight amounts of hexane resulted into an eightfold reduction in the amount of MeOH needed to obtain a yield above 90%, which normally required a MeOH-to-oil ratio of 40:1. This proposed novel approach could provide a more cost-effective method for the esterification of oil to produce biodiesel, that is, reactive separation utilizing carbon-based catalysts under MW irradiation.

Biogasoline production from linoleic acid via catalytic cracking over nickel and copper-doped ZSM-5 catalysts.

Catalytic cracking of vegetable oil mainly processed over zeolites, and among all the zeolites particularly HZMS-5 has been investigated on wide range for renewable and clean gasoline production from various plant oils. Despite the fact that HZSM-5 offers a higher conversion degree and boost aromatics yield, the isomerate yield reduces due to high cracking activity and shape selectivity of HZSM-5. Hence, to overcome these problems, in this study the transition metals, such as nickel and copper doped over HZSM-5 were tested for its efficiencies to improve the isoparaffin compounds. The catalysts were screened with linoleic acid in a catalytic cracking reaction conducted at 450 ᵒC for 90 min in an atmospheric condition in batch reactor. Then, the gasoline composition of the organic liquid product (OLP) was analysed in terms of paraffin, isoparaffin, olefin, naphthenes and aromatics (PIONA). The results showed that Cu/ZSM-5 produced the highest liquid yield of 79.1%, at the same time reduced the production of gas and coke to 18.8% and 0.7%. Furthermore, the desired isoparaffin composition in biogasoline increased from 1.6% to 6.8% and at the same time reduced the oxygenated and aromatic compounds to 15.4% and 59.7%, respectively. The linoleic acid as model compound of rubber seed oil, in the catalytic cracking reaction provides a clearer understanding of the process. Besides, the water gas shift (WGS) reaction in catalytic cracking reaction provides insitu hydrogen production to saturate the branched olefin into the desired isoparaffin and the aromatics into naphthenes.

Recovery of cellulose fibers from oil palm empty fruit bunch for pulp and paper using green delignification approach.

The aim of this work was to recover the cellulose fibers from EFB using low-transition-temperature-mixtures (LTTMs) as a green delignification approach. The hydrogen bonding of LTTMs observed in 1H NMR tends to disrupt the three-dimensional structure of lignin and further remove the lignin from EFB. Delignification process of EFB strands and EFB powder were performed using standard l-malic acid and cactus malic acid-LTTMs. The recovered cactus malic acid-LTTMs showed higher glucose concentration of 8.07 mg/mL than the recovered l-malic acid LTTMs (4.15 mg/mL). This implies that cactus malic acid-LTTMs had higher delignification efficiency which led to higher amount of cellulose hydrolyzed into glucose. The cactus malic acid-LTTMs-delignified EFB was the most feasible fibers for making paper due to its lowest kappa number of 69.84. The LTTMs-delignified EFB has great potential to be used for making specialty papers in pulp and paper industry.

Carbocatalysed hydrolytic cleaving of the glycosidic bond in fucoidan under microwave irradiation.

Biomass valorization involves breaking down naturally occurring long chain polysaccharides into their constituent monomers. The polysaccharide chain consists of monomers adjoined via C (carbon)-O (oxygen) glycosidic linkages that are typically cleaved via hydrolytic scission. In this study, we aimed to recover fucose from the polysaccharide fucoidan, which can be extracted from seaweed biomass. We investigated the depolymerisation behavior of fucoidan sourced from two different species of seaweeds, namely Undaria pinnatifida (F-UP) and Fucus vesiculosus (F-FV). Catalytic depolymerisation experiments were performed using four different carbon-based catalysts - graphene, multiwalled carbon nanotubes (MWCNT), graphene oxide (GO), and reduced graphene oxide (rGO) - under microwave (MW) irradiation. Our results showed that the depolymerisation of fucoidan was best achieved using GO, which was attributed to the abundance of oxygen functionalities on its surface. Furthermore, based on gel permeation chromatography analyses, the depolymerisation of fucoidan was found to follow a two-step process: (1) random scission leading to the production of short-chain oligosaccharides and (2) acid-catalysed hydrolysis of the oligosaccharides to fucose. Because of the longer chain length of F-UP (61 kDa), the highest fucose yield of 17.4% using this species was obtained at a higher temperature of 120 °C in a closed vessel. Meanwhile, in the case of F-FV (1.1 kDa), the highest yield of 54.0% was obtained under reflux conditions at a lower temperature of 104 °C. Our mechanistic study based on semi-empirical quantum calculations also revealed that the recovery of fucose from F-FV is more energetically favoured than from F-UP as a result of their structural differences.

Utilization of rice husk to enhance calcium oxide-based sorbent prepared from waste cockle shells for cyclic CO2 capture in high-temperature condition.

The CO2 capture capacity and cyclic stability of calcium oxide (CaO) prepared from cockle shells (CS) were enhanced by incorporating rice husk (RH) and binder through wet-mixing method. The cyclic reaction of calcination and carbonation was demonstrated using thermal gravimetric analyzer (TGA) which the calcination was performed in a pure N2 environment at 850 °C for 20 min and carbonation at 650 °C for 30 min in 20 vol% of CO2 in N2. The analysis using x-ray fluorescence (XRF) identified silica (Si) as the major elements in the sorbents. The RH-added sorbents also contained several types of metal elements such as which was a key factor to minimize the sintering of the sorbent during the cyclic reaction and contributed to higher CO2 capture capacity. The presence of various morphologies also associated with the improvement of the synthesized sorbents performance. The highest initial CO2 capture capacity was exhibited by CS+10%RH sorbent, which was 12% higher than the RH-free sorbent (CS). However, sorbents with the higher RH loading amount such as 40 and 50 wt% were preferred to maintain high capture capacity when the sorbents were regenerated and extended to the cyclic reaction. The sorbents also demonstrated the lowest average sorption decay, which suggested the most stable sorbent for cyclic-reaction. Once regenerated, the capture capacity of the RH-added sorbent was further increased by 12% when clay was added into the sorbent. Overall, the metal elements in RH and clay were possibly the key factor that enhances the performance of CaO prepared from CS, particularly for cyclic CO2 capture. Graphical abstract Cyclic calcination and carbonation reaction.

Production of gasoline range hydrocarbons from catalytic cracking of linoleic acid over various acidic zeolite catalysts.

Employment of edible oils as alternative green fuel for vehicles had raised debates on the sustainability of food supply especially in the third-world countries. The non-edible oil obtained from the abundantly available rubber seeds could mitigate this issue and at the same time reduce the environmental impact. Therefore, this paper investigates the catalytic cracking reaction of a model compound named linoleic acid that is enormously present in the rubber seed oil. Batch-scale experiments were conducted using 8.8 mL Inconel batch reactor having a cyclic horizontal swing span of 2 cm with a frequency of 60 cycles per minute at 450 °C under atmospheric condition for 90 min. The performance of HZSM-5, HBeta, HFerrierite, HMordenite and HY catalysts was tested for their efficiency in favouring gasoline range hydrocarbons. The compounds present in the organic liquid product were then analysed using GC-MS and classified based on PIONA which stands for paraffin, isoparaffin, olefin, naphthenes and aromatics respectively. The results obtained show that HZSM-5 catalyst favoured gasoline range hydrocarbons that were rich in aromatics compounds and promoted the production of desired isoparaffin. It also gave a higher cracking activity; however, large gaseous as by-products were produced at the same time.

Sustainable green pretreatment approach to biomass-to-energy conversion using natural hydro-low-transition-temperature mixtures.

Natural hydro-low-transition-temperature mixtures (NH-LTTMs) tend to be the most favorable next-generation green solvents for biomass pretreatment, as they are cheap and environmental friendly. The amount of water bound into the NH-LTTMs greatly affected their thermal stability, whereby the highest thermal stability was observed with the water content of 7.6 wt%. It is worth noting that, the highest molar transition energy of NH-LTTMs (47.57 kcal mol-1), which indicated the highest solubility, was optimized with the molar ratio of hydrogen bond donor (HBD)-hydrogen bond acceptor (HBA)-water (2:4:3) at a temperature of 60 °C. Hydrogen bonding networks of the NH-LTTMs, which led to the dissolution of biomass, were confirmed by the alteration in the peaks of the involved bonds and resonance signal to lower field through FTIR and 1H NMR spectra, respectively. The components evidenced in high-resolution mass spectra of extracted lignin showed its high potential to be valorized into useful fuels and chemicals.

Thermogravimetric analysis and kinetic modeling of low-transition-temperature mixtures pretreated oil palm empty fruit bunch for possible maximum yield of pyrolysis oil.

The impacts of low-transition-temperature mixtures (LTTMs) pretreatment on thermal decomposition and kinetics of empty fruit bunch (EFB) were investigated by thermogravimetric analysis. EFB was pretreated with the LTTMs under different duration of pretreatment which enabled various degrees of alteration to their structure. The TG-DTG curves showed that LTTMs pretreatment on EFB shifted the temperature and rate of decomposition to higher values. The EFB pretreated with sucrose and choline chloride-based LTTMs had attained the highest mass loss of volatile matter (78.69% and 75.71%) after 18 h of pretreatment. For monosodium glutamate-based LTTMs, the 24 h pretreated EFB had achieved the maximum mass loss (76.1%). Based on the Coats-Redfern integral method, the LTTMs pretreatment led to an increase in activation energy of the thermal decomposition of EFB from 80.00 to 82.82-94.80 kJ/mol. The activation energy was mainly affected by the demineralization and alteration in cellulose crystallinity after LTTMs pretreatment.

Choline chloride (ChCl) and monosodium glutamate (MSG)-based green solvents from optimized cactus malic acid for biomass delignification.

This work aimed to develop an efficient microwave-hydrothermal (MH) extraction of malic acid from abundant natural cactus as hydrogen bond donor (HBD) whereby the concentration was optimized using response surface methodology. The ideal process conditions were found to be at a solvent-to-feed ratio of 0.008, 120°C and 20min with 1.0g of oxidant, H2O2. Next generation environment-friendly solvents, low transition temperature mixtures (LTTMs) were synthesized from cactus malic acid with choline chloride (ChCl) and monosodium glutamate (MSG) as hydrogen bond acceptors (HBAs). The hydrogen-bonding interactions between the starting materials were determined. The efficiency of the LTTMs in removing lignin from oil palm biomass residues, empty fruit bunch (EFB) was also evaluated. The removal of amorphous hemicellulose and lignin after the pretreatment process resulted in an enhanced digestibility and thermal degradability of biomass.

Characterization of natural low transition temperature mixtures (LTTMs): Green solvents for biomass delignification.

The aim of this work was to characterize the natural low transition temperature mixtures (LTTMs) as promising green solvents for biomass pretreatment with the critical characteristics of cheap, biodegradable and renewable, which overcome the limitations of ionic liquids (ILs). The LTTMs were derived from inexpensive commercially available hydrogen bond acceptor (HBA) and l-malic acid as the hydrogen bond donor (HBD) in distinct molar ratios of starting materials and water. The peaks involved in the H-bonding shifted and became broader for the OH groups. The thermal properties of the LTTMs were not affected by water while the biopolymers solubility capacity of LTTMs was improved with the increased molar ratio of water and treatment temperature. The pretreatment of oil palm biomass was consistence with the screening on solubility of biopolymers. This work provides a cost-effective alternative to utilize microwave hydrothermal extracted green solvents such as malic acid from natural fruits and plants.

Supercritical carbon dioxide extraction of fucoxanthin from Undaria pinnatifida.

Undaria pinnatifida, commonly known as wakame in Japan, is one species of brown seaweeds containing valuable bioactive organic compounds such as fucoxanthin, a carotenoid, which has numerous functional properties. However, most of the seaweeds that do not meet strict quality standards are normally discarded as wastes or returned to the sea, a situation which is becoming an environmental concern. In this research, supercritical carbon dioxide (SCCO2) extraction was investigated for the isolation of fucoxanthin. SCCO2 extraction experiments were carried out at temperature range of 25-60 °C and pressure range of 20-40 MPa, at a carbon dioxide flow rate of 1.0-4.0 mL/min. Results showed that fucoxanthin recovery closed to 80% could be obtained at 40 °C and 40 MPa in extraction time of 180 min. The recovery increased with decreasing temperature and increasing pressure. Pretreatment with microwave (MW) also enhanced the efficiency of extraction due most likely to disruption of the cell membrane. Application of SCCO2, generally regarded as safe and environmentally benign solvent, for extraction of useful bioactive compounds from unwanted or substandard seaweeds look promising in the near future. The extracts obtained using the method can be utilized as food and pharmaceutical additive, and can be used in the development of new health supplements.

Polyphenolic contents and antioxidant activities of Lawsonia inermis leaf extracts obtained by microwave-assisted hydrothermal method.

Extracts obtained by microwave-assisted hydrothermal extraction of Lawsonia inermis leaves were evaluated for the presence of polyphenolic compounds and antioxidant activities. Extraction experiments were performed in temperature-controlled mode at a range of 100 to 200 degrees C, and extraction time of 5 to 30 min, and microwave-controlled mode at a power from 300-700 W, in irradiation time of 30 to 120 s. Polyphenolic contents were measured using Folin-Ciocalteau method, while antioxidant properties were analyzed using DPPH radical scavenging activities (RSA) expressed in BHA equivalents. Results showed that best values of RSA were obtained at mild temperature range of 100-120 degrees C. Controlling microwave power at short irradiation time gave better results than temperature-controlled treatment as well. Furthermore, comparison with the result obtained at room temperature confirmed that the use of microwave was more effective for extracting polar components that normally possess higher antioxidant activities.

Recovery of oil components of okara by ethanol-modified supercritical carbon dioxide extraction.

Recovery of the oil components of okara by ethanol-modified supercritical carbon dioxide extraction was investigated at 40-80 degrees C temperature and 12-30 MPa pressure. In a typical run (holding period of 2 h, continuous flow extraction of 5 h), results indicated that the oil component could be best obtained with a recovery of 63.5% at relatively low temperature of 40 degrees C and mild pressure of 20 MPa in the presence of 10 mol% EtOH as entrainer. Based on gas chromatography-mass spectrometry (GC-MS) analysis, the extracts consisted mainly of fatty acids and phytosterols, and traces of decadienal. Folin-Ciocalteau estimates of total phenols showed that addition of EtOH as entrainer increased the yield and the amount of phenolic compounds in the extracts. The amounts of two primary soy isoflavones, genistein and daidzein, in the extracts also increased with increasing amount of EtOH.

Metal elution from Ni- and Fe-based alloy reactors under hydrothermal conditions.

Elution of metals from Ni- and Fe-based alloy (i.e. Inconel 625 and SUS 316) under hydrothermal conditions was investigated. Results showed that metals could be eluted even in a short contact time. At subcritical conditions, a significant amount of Cr was extracted from SUS 316, while only traces of Ni, Fe, Mo, and Mn were eluted. In contrast, Ni was removed in significant amounts compared to Cr when Inconel 625 was tested. Several factors including temperature and contact time were found to affect elution behavior. The presence of air in the fluid even promoted elution under subcritical conditions.

Qualitative investigation on hydrothermal treatment of Hinoki (Chamaecyparis obtusa) bark for production of useful chemicals.

Hydrothermal treatment of an outer layer of a bark of Hinoki (Chamaecyparis obtusa) tree was investigated qualitatively for the possibility of utilizing residual forest biomass to produce valuable chemicals. Experiments were carried out in a semibatch reactor apparatus that allows the study of the effect of reaction temperatures in a single run. Gas chromatography-mass spectrometry analyses show the presence of useful chemicals such as furfural, aromatic compounds (1,3-di-tert-butyl benzene and 2,4-di-tert-butyl phenol), and fatty acids (myristic acid, palmitic acid, and stearic acid) in the products.