RESUMEN
Digitally printed organic photodiodes (OPDs) are of great interest for the cost-efficient additive manufacturing of single and multidevice detection systems with full freedom of design. Recently reported high-performance non-fullerene acceptors (NFAs) can address the crucial demands of future applications in terms of high operational speed, tunable spectral response, and device stability. Here, we present the first demonstration of inkjet and aerosol-jet printed OPDs based on the high-performance NFA, IDTBR, in combination with poly(3-hexylthiophene), exhibiting a spectral response up to the near-infrared (NIR) region. These digitally printed devices reach record responsivities up to 300 mA/W in the visible and NIR spectrum, competing with current commercially available technologies based on Si. Furthermore, their fast dynamic response with cutoff frequencies surpassing 2 MHz outperforms most of the state-of-the-art OPDs. The successful process translation from spin-coating to printing is highlighted by the marginal loss in performance compared to the reference devices, which reach responsivities of 400 mA/W and detection speeds of more than 4 MHz. The achieved high device performance and the industrial relevance of the developed fabrication process provide NFAs with an enormous potential for the development of printed photodetection systems.
RESUMEN
Digital printing enables solution processing of functional materials and opens a new route to fabricate low-cost electronic devices. One crucial parameter that affects the wettability of inks for all printing techniques is the surface free energy (SFE) of the substrate. Siloxanes, with their huge variety of side chains and their ability to form self-assembled monolayers, offer exhaustive control of the substrate SFE from hydrophilic to hydrophobic. Thus, siloxane treatment is a suitable approach to adjust the substrate conditions to the desired ink, instead of optimizing the ink to an arbitrary substrate. In this work, the influence of different fluorinated and nonfluorinated siloxanes on the SFE of different substrates, such as polymers, glasses, and metals, are examined. By mixing several siloxanes, we demonstrate the fine tuning of the surface energy. The polar and dispersive components of the SFE are determined by the Owens-Wendt-Rabel-Kaelble (OWRK) method. Furthermore, the impact of the siloxanes and therefore the SFE on the pinning of droplets and wet films are assessed via dynamic contact angle measurements. SFE-optimized substrates enable tailoring the resolution of inkjet printed silver structures. A nanoparticulate silver ink was used for printing single drops, lines, and source-drain electrodes for transistors. These were examined in terms of diameter, edge quality, and functionality. We show that by adjusting the SFE of an arbitrary substrate, the printed resolution is substantially increased by minimizing the printed drop size by up to 70%.
RESUMEN
The integration of periodic nanodisk arrays into the channel of a light-emitting field-effect transistor leads to enhanced and directional electroluminescence from thin films of purified semiconducting single-walled carbon nanotubes. The maximum enhancement wavelength is tunable across the near-infrared and is directly linked to the periodicity of the arrays. Numerical calculations confirm the role of increased local electric fields in the observed emission modification. Large current densities are easily achieved due to the high charge carrier mobilities of carbon nanotubes and will facilitate new electrically driven plasmonic devices.
RESUMEN
Self-organization of functional materials induced by low surface-energetic direct printed structures is presented. This study investigates fundamental fluid and substrate interactions and fabricates all-printed small area organic photodetectors with On-Off ratios of ≈10(5) and dark current densities of ≈10(-4) mA cm(-2) , as well as ring oscillators based on n-type organic field-effect transistors showing working frequencies up to 400 Hz.
RESUMEN
Hybrid photonic-plasmonic modes in periodic arrays of metallic nanostructures offer a promising trade-off between high-quality cavities and subdiffraction mode confinement. However, their application in electrically driven light-emitting devices is hindered by their sensitivity to the surrounding environment and to charge injecting metallic electrodes in particular. Here, we demonstrate that the planar structure of light-emitting field-effect transistor (LEFET) ensures undisturbed operation of the characteristic modes. We incorporate a square array of gold nanodisks into the charge transporting and emissive layer of a polymer LEFET in order to tailor directionality and emission efficiency via the Purcell effect and variation of the fractional local density of states in particular. Angle- and polarization-resolved spectra confirm that the enhanced electroluminescence correlates with the dispersion curves of the surface lattice resonances supported by these structures. These LEFETs reach current densities on the order of 10 kA/cm2, which may pave the way toward practical optoelectronic devices with tailored emission patterns and potentially electrically pumped plasmonic lasers.
