Dry-spun carbon nanotube ultrafiltration membranes tailored by anti-viral metal oxide coatings for human coronavirus 229E capture in water.

Although waterborne virus removal may be achieved using separation membrane technologies, such technologies remain largely inefficient at generating virus-free effluents due to the lack of anti-viral reactivity of conventional membrane materials required to deactivating viruses. Here, a stepwise approach towards simultaneous filtration and disinfection of Human Coronavirus 229E (HCoV-229E) in water effluents, is proposed by engineering dry-spun ultrafiltration carbon nanotube (CNT) membranes, coated with anti-viral SnO2 thin films via atomic layer deposition. The thickness and pore size of the engineered CNT membranes were fine-tuned by varying spinnable CNT sheets and their relative orientations on carbon nanofibre (CNF) porous supports to reach thicknesses less than 1 µm and pore size around 28 nm. The nanoscale SnO2 coatings were found to further reduce the pore size down to ∼21 nm and provide more functional groups on the membrane surface to capture the viruses via size exclusion and electrostatic attractions. The synthesized CNT and SnO2 coated CNT membranes were shown to attain a viral removal efficiency above 6.7 log10 against HCoV-229E virus with fast water permeance up to ∼4 × 103 and 3.5 × 103 L.m-2.h-1.bar-1, respectively. Such high performance was achieved by increasing the dry-spun CNT sheets up to 60 layers, orienting successive 30 CNT layers at 45°, and coating 40 nm SnO2 on the synthesized membranes. The current study provides an efficient scalable fabrication scheme to engineer flexible ultrafiltration CNT-based membranes for cost-effective filtration and inactivation of waterborne viruses to outperform the state-of-the-art ultrafiltration membranes.

The impact of PET microplastic fibres on PVDF ultrafiltration performance - A short-term assessment of MP fouling in simple and complex matrices.

Wastewater treatment plants (WWTPs) are key components for the capture of microplastics (MPs) before they are released into natural waterways. Removal efficiencies as high as 99% may be achieved but sub-micron MPs as well as nanoplastics have been overlooked because of analytical limitations. Furthermore, short MP fibres are of concern because of their low capture rate as well as the lack of understanding of their influence on purification system efficiency. This study has investigated the impact of poly(ethylene terephthalate) (PET) short nanofibres on the performance of polyvinylidene fluoride (PVDF) ultrafiltration membranes during cross-flow operation. Model MP fibres with an average length of 10 ± 7 µm and a diameter of 142 ± 40 nm were prepared via a combination of electrospinning and fine cutting using a cryomicrotome. The manufactured MPs were added to both pure and synthetic domestic wastewater at a concentration of 1 mg.L-1 to determine their impact on the performance of PVDF ultrafiltration membranes. The results show that PET fibres attach to the membrane in a disorganised manner with low pore coverage. The water flux was decreased by 8% for MPs in pure water and no noticeable effect in wastewater after 3 days of filtration. Additionally, the nutrient removal efficiency of the membrane was not altered by the presence of PET MPs. These findings show that MP fibres do not significantly influence the early stages of filtration for a standard concentration of MPs in wastewater treatment plant studies.

Novel Polysulfone/Carbon Nanotube-Polyamide Thin Film Nanocomposite Membranes with Improved Water Flux for Forward Osmosis Desalination.

Forward osmosis (FO) is a promising alternative to reverse osmosis (RO) in membrane-based water desalination. In the current study, carboxylated multiwalled carbon nanotubes (MWCNTs) were incorporated in a polyamide (PA) layer formed on top of a polysulfone porous support, resulting in a thin film nanocomposite (TFN) membrane. The amount of MWCNTs was varied (0.01, 0.05, 0.1, and 0.2 wt/vol %). The FO performance was investigated using deionized water as the feed solution and 2 M NaCl as the draw solution. It was found that the carboxylated MWCNTs enhanced the membrane hydrophilicity, surface roughness, and porosity. Such combined effects are believed to have led to enhanced FO water flux. TFN 0.2 showed the highest FO water flux of 73.15 L/m2 h, an improvement of 67% compared to the blank thin-film composite (TFC) membrane and significantly better than the values reported in the literature. Direct observation by transmission electron microscopy revealed the presence of some open-ended CNTs favorably oriented across the PA layer. Those are believed to have facilitated the transport of water through their inner cores and contributed to the increase in water flux. However, this was at the expense of salt rejection and reverse solute flux performance. The best performing membrane was found to be TFN 0.01. It exhibited a salt rejection of 90.1% with a FO water flux of 50.23 L/m2 h, which is 13% higher than the TFC membrane, and a reverse solute flux of 2.76 g/m2 h, which is 21% lower than the TFC membrane. This TFN 0.01 membrane also outperformed the TFN membranes reported in the literature.