Multifunctional Separator Allows Stable Cycling of Potassium Metal Anodes and of Potassium Metal Batteries.

This is the first report of a multifunctional separator for potassium-metal batteries (KMBs). Double-coated tape-cast microscale AlF3 on polypropylene (AlF3 @PP) yields state-of-the-art electrochemical performance: symmetric cells are stable after 1000 cycles (2000 h) at 0.5 mA cm-2 and 0.5 mAh cm-2 , with 0.042 V overpotential. Stability is maintained at 5.0 mA cm-2 for 600 cycles (240 h), with 0.138 V overpotential. Postcycled plated surface is dendrite-free, while stripped surface contains smooth solid electrolyte interphase (SEI). Conventional PP cells fail rapidly, with dendrites at plating, and "dead metal" and SEI clumps at stripping. Potassium hexacyanoferrate(III) cathode KMBs with AlF3 @PP display enhanced capacity retention (91% at 100 cycles vs 58%). AlF3 partially reacts with K to form an artificial SEI containing KF, AlF3 , and Al2 O3 phases. The AlF3 @PP promotes complete electrolyte wetting and enhances uptake, improves ion conductivity, and increases ion transference number. The higher of K+ transference number is ascribed to the strong interaction between AlF3 and FSI- anions, as revealed through 19 F NMR. The enhancement in wetting and performance is general, being demonstrated with ester- and ether-based solvents, with K-, Na-, or Li- salts, and with different commercial separators. In full batteries, AlF3 prevents Fe crossover and cycling-induced cathode pulverization.

Tuning Metal Elements in Open Frameworks for Efficient Oxygen Evolution and Oxygen Reduction Reaction Catalysts.

Electrochemical methods are promising technical routes for future clean energy storage and conversion. Most of the electrochemical methods involve oxygen reactions. Unfavorable kinetics and sluggish reactions are the main challenges for these processes. We report here a facile synthesis of highly efficient oxygen evolution reaction (OER) and oxygen reduction reaction (ORR) catalysts. The catalysts are synthesized through the fine-tuning of metal ions (M, specifically Co, Ni, Zn, and Cu) in Prussian blue analogues (PBAs) and thus termed as M-PBAs. The CoNi-PBA-2 catalyst shows the highest activity toward OER with an onset potential at 280 mV and a Tafel slope of 63 mV dec-1. Zn-PBA catalysts demonstrate high selectivity in two-electron-transfer ORR. The H2O2 yield is as high as 88% at 0 V vs RHE. Density functional theory (DFT) calculations also confirm the high selectivity of Zn-PBA toward H2O2 in ORR.

Millisecond Conversion of Metastable 2D Materials by Flash Joule Heating.

Controllable phase engineering is vital for precisely tailoring material properties since different phase structures have various electronic states and atomic arrangements. Rapid synthesis of thermodynamically metastable materials, especially two-dimensional metastable materials, with high efficiency and low cost remains a large challenge. Here we report flash Joule heating (FJH) as an electrothermal method to achieve the bulk conversion of transition metal dichalcogenides, MoS2 and WS2, from 2H phases to 1T phases in milliseconds. The conversions can reach up to 76% of flash MoS2 using tungsten powder as conductive additive. Different degrees of phase conversion can be realized by controlling the FJH conditions, such as reaction duration and additives, which allows the study of ratio-dependent properties. First-principles calculations confirm that structural processes associated with the FJH, such as vacancy formation and charge accumulation, result in stabilization of the 1T phases. FJH offers rapid access to bulk quantities of the hitherto hard-to-access 1T phases, a promising method for further fundamental research and diverse applications of metastable phases.

CO2 to Formic Acid Using Cu-Sn on Laser-Induced Graphene.

Converting CO2 into fuels and other value-added chemicals via an electrochemical reduction method has recently attracted great interest. However, there are still challenges to find suitable catalysts with high selectivity toward the formic acid formation. Here, we report the bimetallic CuSn-based catalyst to reduce CO2 to formic acid by optimizing the ratio of Cu to Sn to achieve the optimal selectivity. The catalyst is generated on laser-induced graphene. Among the catalysts, CuSn-4 with Cu/Sn atomic ratio close to 1:2 shows a faradaic efficiency of 99% toward formic acid with a high partial current density of 26 mA/cm2. Density functional theory calculations demonstrate that OCHO* intermediate formation is more favorable than that of COOH* on Sn sites, while OCHO* intermediate formation is moderate on Cu sites. The synergetic catalytic effect between Cu and Sn would further favor HCOOH formation. This study provides significant insight into the mechanism of formic acid formation.

Laser-Induced Silicon Oxide for Anode-Free Lithium Metal Batteries.

The development of a rechargeable Li metal anode (LMA) is an important milestone for improved battery technology. Practical issues hindering LMAs are the formation of Li dendrites and inactive Li during plating and stripping processes, which can cause short circuits, thermal runaway, and low coulombic efficiency (CE). Here, the use of a laser-induced silicon oxide (LI-SiOx ) layer derived from a commercial adhesive tape to improve the reversibility of Li metal batteries (LMBs) is studied. The silicone-based adhesive of the tape is converted by a commercial infrared laser into a homogeneous porous SiOx layer deposited directly over the current collector. The coating results in superior performance by suppressing the formation of Li dendrites and inactive Li and presenting higher average CE of 99.3% (2.0 mAh cm-2 at 2.0 mA cm-2 ) compared to bare electrodes. The thickness and morphology of the deposited Li is investigated, revealing a different mechanism of Li deposition on coated electrodes. The laser coating affords a method that is fast and avoids the use of toxic organic solvents and extensive drying times. The improved performance with the SiOx coating is demonstrated in LMB with a zero-excess ("anode-free") configuration where a 100% improved performance is verified.

Gram-scale bottom-up flash graphene synthesis.

Most bulk-scale graphene is produced by a top-down approach, exfoliating graphite, which often requires large amounts of solvent with high-energy mixing, shearing, sonication or electrochemical treatment1-3. Although chemical oxidation of graphite to graphene oxide promotes exfoliation, it requires harsh oxidants and leaves the graphene with a defective perforated structure after the subsequent reduction step3,4. Bottom-up synthesis of high-quality graphene is often restricted to ultrasmall amounts if performed by chemical vapour deposition or advanced synthetic organic methods, or it provides a defect-ridden structure if carried out in bulk solution4-6. Here we show that flash Joule heating of inexpensive carbon sources-such as coal, petroleum coke, biochar, carbon black, discarded food, rubber tyres and mixed plastic waste-can afford gram-scale quantities of graphene in less than one second. The product, named flash graphene (FG) after the process used to produce it, shows turbostratic arrangement (that is, little order) between the stacked graphene layers. FG synthesis uses no furnace and no solvents or reactive gases. Yields depend on the carbon content of the source; when using a high-carbon source, such as carbon black, anthracitic coal or calcined coke, yields can range from 80 to 90 per cent with carbon purity greater than 99 per cent. No purification steps are necessary. Raman spectroscopy analysis shows a low-intensity or absent D band for FG, indicating that FG has among the lowest defect concentrations reported so far for graphene, and confirms the turbostratic stacking of FG, which is clearly distinguished from turbostratic graphite. The disordered orientation of FG layers facilitates its rapid exfoliation upon mixing during composite formation. The electric energy cost for FG synthesis is only about 7.2 kilojoules per gram, which could render FG suitable for use in bulk composites of plastic, metals, plywood, concrete and other building materials.

Electronic Metal-Support Interaction-Modified Structures and Catalytic Activity of CeOx Overlayers in CeOx /Ag Inverse Catalysts.

Invited for the cover of this issue is Weixin Huang and co-workers at the University of Science and Technology of China. The image depicts the strong influence of electronic metal-support interaction (EMSI) on electronic structures and the catalytic activity of CeOx /Ag inverse catalysts. Read the full text of the article at 10.1002/chem.201904134.

Pore Characteristics for Efficient CO2 Storage in Hydrated Carbons.

Development of new approaches for carbon dioxide (CO2) capture is important in both scientific and technological aspects. One of the emerging methods in CO2 capture research is based on the use of gas-hydrate crystallization in confined porous media. Pore dimensions and surface functionality of the pores play important roles in the efficiency of CO2 capture. In this report, we summarize work on several porous carbons (PCs) that differ in pore dimensions that range from supermicropores to mesopores, as well as surfaces ranging from hydrophilic to hydrophobic. Water was imbibed into the PCs, and the CO2 uptake performance, in dry and hydrated forms, was determined at pressures of up to 54 bar to reveal the influence of pore characteristics on the efficiency of CO2 capture and storage. The final hydrated carbon materials had H2O-to-carbon weight ratios of 1.5:1. Upon CO2 capture, the H2O/CO2 molar ratio was found to be as low as 1.8, which indicates a far greater CO2 capture capacity in hydrated PCs than ordinarily seen in CO2-hydrate formations, wherein the H2O/CO2 ratio is 5.72. Our mechanistic proposal for attainment of such a low H2O/CO2 ratio within the PCs is based on the finding that most of the CO2 is captured in gaseous form within micropores of diameter <2 nm, wherein it is blocked by external CO2-hydrate formations generated in the larger mesopores. Therefore, to have efficient high-pressure CO2 capture by this mechanism, it is necessary to have PCs with a wide pore size distribution consisting of both micropores and mesopores. Furthermore, we found that hydrated microporous or supermicroporous PCs do not show any hysteretic CO2 uptake behavior, which indicates that CO2 hydrates cannot be formed within micropores of diameter 1-2 nm. Alternatively, mesoporous and macroporous carbons can accommodate higher yields of CO2 hydrates, which potentially limits the CO2 uptake capacity in those larger pores to a H2O/CO2 ratio of 5.72. We found that high nitrogen content prevents the formation of CO2 hydrates presumably due to their destabilization and associated increase in system entropy via stronger noncovalent interactions between the nitrogen functional groups and H2O or CO2.

Electronic Metal-Support Interaction-Modified Structures and Catalytic Activity of CeOx Overlayers in CeOx /Ag Inverse Catalysts.

Electronic metal-support interactions (EMSIs) of oxide-supported metal catalysts strongly modifies the electronic structures of the supported metal nanoparticles. The strong influence of EMSIs on the electronic structures of oxide overlayers on metal nanoparticles employing cerium oxides/Ag inverse catalysts is reported herein. Ce2 O3 overlayers were observed to exclusively form on Ag nanocrystals at low cerium loadings and be resistant to oxidation treatments up to 250 °C, whereas CeO2 overlayers gradually developed as the cerium loading increased. Ag cubes enclosed by {001} facets with a smaller work function exert a stronger EMSI effect on the CeOx overlayers than Ag cubes enclosed by {111} facets. Only the CeO2 overlayers with a fully developed bulk CeO2 electronic structure significantly promote the catalytic activity of Ag nanocrystals in CO oxidation, whereas cerium oxide overlayers with other electronic structures do not. These results successfully extend the concept of EMSIs from oxide-supported metal catalysts to metal-supported oxide catalysts.

Sustainable Synthesis of Bright Green Fluorescent Nitrogen-Doped Carbon Quantum Dots from Alkali Lignin.

Sustainable, inexpensive, and environmentally friendly biomass waste can be exploited for large-scale production of carbon nanomaterials. Here, alkali lignin was employed as a precursor to synthesize carbon quantum dots (CQDs) with bright green fluorescence through a simple one-pot route. The prepared CQDs had a size of 1.5-3.5 nm, were water-dispersible, and showed wonderful biocompatibility, in addition to their excellent photoluminescence and electrocatalysis properties. These high-quality CQDs could be used in a wide range of applications such as metal-ion detection, cell imaging, and electrocatalysis. The wide range of biomass lignin feedstocks provide a green, low-cost, and viable strategy for producing high-quality fluorescent CQDs and enable the conversion of biomass waste into high-value products that promote sustainable development of the economy and human society.

Highly Efficient Hydrogen Evolution from a Mesoporous Hybrid of Nickel Phosphide Nanoparticles Anchored on Cobalt Phosphosulfide/Phosphide Nanosheet Arrays.

Facile design of low-cost and high-efficiency catalysts with earth-abundant and cheap materials is desirable to replace platinum (Pt) for the hydrogen evolution reaction (HER) in water splitting, but the development of such HER catalysts with Pt-like activity using simple strategies remains challenging. A mesoporous hybrid catalyst of nickel phosphides nanoparticles and cobalt phosphosulfide/phosphide (CoS|Ni|P) nanosheet arrays for HER is reported here, which is developed by a facile three-step approach consisting of electrodeposition, thermal sulfurization, and phosphorization. This hybrid catalyst is highly robust and stable in acid for HER, and is distinguished by very low overpotentials of 41, 88, and 150 mV to achieve 10, 100, and 1000 mA cm-2 , respectively, as well as a small Tafel slope (45.2 mV dec-1 ), and a large exchange current density (964 µA cm-2 ). It is among the most efficient earth-abundant catalysts reported thus far for HER. More importantly, this electrocatalyst has electrochemical durability over 20 h under a wide range of current densities (up to 1 A cm-2 ) in acidic conditions, as well as very high turnover frequencies of 0.40 and 1.26 H2 s-1 at overpotentials of 75 and 100 mV, respectively, showing that it has great potential for practical applications in large-scale water electrolysis.

Oxidized Laser-Induced Graphene for Efficient Oxygen Electrocatalysis.

An efficient metal-free catalyst is presented for oxygen evolution and reduction based on oxidized laser-induced graphene (LIG-O). The oxidation of LIG by O2 plasma to form LIG-O boosts its performance in the oxygen evolution reaction (OER), exhibiting a low onset potential of 260 mV with a low Tafel slope of 49 mV dec-1 , as well as an increased activity for the oxygen reduction reaction. Additionally, LIG-O shows unexpectedly high activity in catalyzing Li2 O2 decomposition in Li-O2 batteries. The overpotential upon charging is decreased from 1.01 V in LIG to 0.63 V in LIG-O. The oxygen-containing groups make essential contributions, not only by providing the active sites, but also by facilitating the adsorption of OER intermediates and lowering the activation energy.

Design of Nanoparticle-Based Carriers for Targeted Drug Delivery.

Nanoparticles have shown promise as both drug delivery vehicles and direct antitumor systems, but they must be properly designed in order to maximize efficacy. Computational modeling is often used both to design new nanoparticles and to better understand existing ones. Modeled processes include the release of drugs at the tumor site and the physical interaction between the nanoparticle and cancer cells. In this article, we provide an overview of three different targeted drug delivery methods (passive targeting, active targeting and physical targeting), compare methods of action, advantages, limitations, and the current stage of research. For the most commonly used nanoparticle carriers, fabrication methods are also reviewed. This is followed by a review of computational simulations and models on nanoparticle-based drug delivery.