A chip-based potentiometric sensor for a Zika virus diagnostic using 3D surface molecular imprinting.

The latest Zika virus (ZIKV) pandemic caused great international concern from explosively proliferating throughout the Americas. Currently, there is no vaccine to prevent Zika virus infection and available tests rely on antibodies or RNA. Unfortunately, antibody-based detection systems can result in false positive results and RNA-based detection systems are costly, time-consuming, and impractical for testing in remote regions. In this study, a potential point-of-care (POC) diagnostic system was developed using a chip-based potentiometric sensor to detect Zika virus using a 3D molecular imprinting technique. This chip-based potentiometric sensor system was able to detect 10-1 PFU mL-1 ZIKV in a buffered solution under 20 minutes without any sample manipulation. This sensor was tested against Dengue virus at clinical viral loads and showed no sign of cross-reactivity. When tested against human saliva samples containing clinical viral loads, this sensor was able to detect 10 PFU mL-1 ZIKV among the pool of bio-macromolecules. The high sensitivity and high selectivity demonstrated here proved that this lab-on-a-chip diagnostic has the potential to become a POC detection system for rapid and accurate screening of flaviviruses.

Regulating substrate mechanics to achieve odontogenic differentiation for dental pulp stem cells on TiO2 filled and unfilled polyisoprene.

We have shown that materials other than hydrogels commonly used in tissue engineering can be effective in enabling differentiation of dental pulp stem cells (DPSC). Here we demonstrate that a hydrophobic elastomer, polyisoprene (PI), a component of Gutta-percha, normally used to obturate the tooth canal, can also be used to initiate differentiation of the pulp. We showed that PI substrates without additional coating promote cell adhesion and differentiation, while their moduli can be easily adjusted either by varying the coating thickness or incorporation of inorganic particles. DPSC plated on those PI substrates were shown, using SPM and hysitron indentation, to adjust their moduli to conform to differentially small changes in the substrate modulus. In addition, optical tweezers were used to separately measure the membrane and cytoplasm moduli of DPSC, with and without Rho kinase inhibitor. The results indicated that the changes in modulus were attributed predominantly to changes within the cytoplasm, rather than the cell membrane. CLSM was used to identify cell morphology. Differentiation, as determined by qRT-PCR, of the upregulation of OCN, and COL1α1 as well as biomineralization, characterized by SEM/EDAX, was observed on hard PI substrates in the absence of induction factors, i.e. dexamethasone, with moduli 3-4 MPa, regardless of preparation. SEM showed that even though biomineralization was deposited on both spun cast thin PI and filled thick PI substrates, the minerals were aggregated into large clusters on thin PI, and uniformly distributed on filled thick PI, where it was templated within banded collagen fibers. STATEMENT OF SIGNIFICANCE: This manuscript demonstrates the potential of polyisoprene (PI), an elastomeric polymer, for use in tissue engineering. We show how dental pulp stem cells adjust their moduli continuously to match infinitesimally small changes in substrate mechanics, till a critical threshold is reached when they will differentiate. The lineage of differentiation then becomes a sensitive function of both mechanics and morphology for a given chemical composition. Since PI is a major component of Gutta-percha, the FDA approved material commonly used for obturating the root canal, this work suggests that it can easily be adapted for in vivo use in dental regeneration.

The influence of roughness on stem cell differentiation using 3D printed polylactic acid scaffolds.

With the increase in popularity of 3D printing, an important question arises as to the equivalence between devices manufactured by standard methods vs. those presenting with identical bulk specifications, but manufactured via fused deposition modeling (FDM) printing. Using thermal imaging in conjunction with electron and atomic force microscopy, we demonstrate that large thermal gradients, whose distribution is difficult to predict, are associated with FDM printing and result in incomplete fusion and sharkskin of the printing filament. Even though these features are micro or submicron scale, and hence may not interfere with the intended function of the device, they can have a profound influence if the device comes in contact with living tissue. Dental pulp stem cells were cultured on substrates of identical dimensions, which were either printed or molded from the same PLA stock material. The cultures exhibited significant differences in plating efficiency, migration trajectory, and morphology at early times stemming from attempts by the cells to minimize cytoplasm deformation as they attempt to adhere on the printed surfaces. Even though biomineralization without dexamethasone induction was observed in all cultures at later times, different gene expression patterns were observed on the two surfaces. (Osteogenic markers were upregulated on molded substrates, while odontogenic markers were upregulated on the FDM printed surfaces.) Our results clearly indicate that the method of manufacturing is an important consideration in comparing devices, which come in contact with living tissues.

Continual cell deformation induced via attachment to oriented fibers enhances fibroblast cell migration.

Fibroblast migration is critical to the wound healing process. In vivo, migration occurs on fibrillar substrates, and previous observations have shown that a significant time lag exists before the onset of granulation tissue. We therefore conducted a series of experiments to understand the impact of both fibrillar morphology and migration time. Substrate topography was first shown to have a profound influence. Fibroblasts preferentially attach to fibrillar surfaces, and orient their cytoplasm for maximal contact with the fiber edge. In the case of en-mass cell migration out of an agarose droplet, fibroblasts on flat surfaces emerged with an enhanced velocity, v = 52µm/h, that decreases to the single cell value, v = 28µm/h within 24 hours and remained constant for at least four days. Fibroblasts emerging on fibrillar surfaces emerged with the single cell velocity, which remained constant for the first 24 hours and then increased reaching a plateau with more than twice the initial velocity within the next three days. The focal adhesions were distributed uniformly in cells on flat surfaces, while on the fibrillar surface they were clustered along the cell periphery. Furthermore, the number of focal adhesions for the cells on the flat surfaces remained constant, while it decreased on the fibrillar surface during the next three days. The deformation of the cell nuclei was found to be 50% larger on the fiber surfaces for the first 24 hours. While the mean deformation remained constant on the flat surface, it increased for the next three days by 24% in cells on fibers. On the fourth day, large actin/myosin fibers formed in cells on fibrillar surfaces only and coincided with a change from the standard migration mechanism involving extension of lamellipodia, and retraction of the rear, to one involving strong contractions oriented along the fibers and centered about the nucleus.