Towards health-based nano reference values (HNRVs) for occupational exposure: Recommendations from an expert panel.

Unique physicochemical characteristics of engineered nanomaterials (ENMs) suggest the need for nanomaterial-specific occupational exposure limits (OELs). Setting these limits remains a challenge. Therefore, the aim of this study was to set out a framework to evaluate the feasibility of deriving advisory health-based occupational limit values for groups of ENMs, based on scientific knowledge. We have used an expert panel approach to address three questions: 1) What ENM-categories should be distinguished to derive advisory health-based occupational limit values (or health-based Nano Reference Values, HNRVs) for groups of ENMs? 2) What evidence would be needed to define values for these categories? And 3) How much effort would it take to achieve this? The panel experts distinguished six possible categories of HNRVs: A) WHO-fiber-like high aspect ratio ENMs (HARNs), B) Non-WHO-fiber-like HARNs and other non-spheroidal ENMs, C) readily soluble spheroidal ENMs, D) biopersistent spheroidal ENMs with unknown toxicity, E) biopersistent spheroidal ENMs with substance-specific toxicity and F) biopersistent spheroidal ENMs with relatively low substance-specific toxicity. For category A, the WHO-fiber-like HARNs, agreement was reached on criteria defining this category and the approach of using health-based risk estimates for asbestos to derive the HNRV. For category B, a quite heterogeneous category, more toxicity data are needed to set an HNRV. For category C, readily soluble spheroidal ENMs, using the OEL of their molecular or ionic counterpart would be a good starting point. For the biopersistent ENMs with unknown toxicity, HNRVs cannot be applied as case-by-case testing is required. For the other biopersistent ENMs in category E and F, we make several recommendations that can facilitate the derivation of these HNRVs. The proposed categories and recommendations as outlined by this expert panel can serve as a reference point for derivation of HNRVs when health-based OELs for ENMs are not yet available.

Higher viral load and infectivity increase risk of aerosol transmission for Delta and Omicron variants of SARS-CoV-2.

BACKGROUND: Airborne transmission of SARS-CoV-2 is an important route of infection. For the wildtype (WT) only a small proportion of those infected emitted large quantities of the virus. The currently prevalent variants of concern, Delta (B1.617.2) and Omicron (B.1.1.529), are characterized by higher viral loads and a lower minimal infective dose compared to the WT. We aimed to describe the resulting distribution of airborne viral emissions and to reassess the risk estimates for public settings given the higher viral load and infectivity. METHOD: We reran the Monte Carlo modelling to estimate viral emissions in the fine aerosol size range using available viral load data. We also updated our tool to simulate indoor airborne transmission of SARS-CoV-2 by including a CO2 calculator and recirculating air cleaning devices. We also assessed the consequences of the lower critical dose on the infection risk in public settings with different protection strategies. RESULTS: Our modelling suggests that a much larger proportion of individuals infected with the new variants are high, very high or super-emitters of airborne viruses: for the WT, one in 1,000 infected was a super-emitter; for Delta one in 30; and for Omicron one in 20 or one in 10, depending on the viral load estimate used. Testing of the effectiveness of protective strategies in view of the lower critical dose suggests that surgical masks are no longer sufficient in most public settings, while correctly fitted FFP2 respirators still provide sufficient protection, except in high aerosol producing situations such as singing or shouting. DISCUSSION: From an aerosol transmission perspective, the shift towards a larger proportion of very high emitting individuals, together with the strongly reduced critical dose, seem to be two important drivers of the aerosol risk, and are likely contributing to the observed rapid spread of the Delta and Omicron variants of concern. Reducing contacts, always wearing well-fitted FFP2 respirators when indoors, using ventilation and other methods to reduce airborne virus concentrations, and avoiding situations with loud voices seem critical to limiting these latest waves of the COVID-19 pandemic.

NanoSafe III: A User Friendly Safety Management System for Nanomaterials in Laboratories and Small Facilities.

Research in nanoscience continues to bring forward a steady stream of new nanomaterials and processes that are being developed and marketed. While scientific committees and expert groups deal with the harmonization of terminology and legal challenges, risk assessors in research labs continue to have to deal with the gap between regulations and rapidly developing information. The risk assessment of nanomaterial processes is currently slow and tedious because it is performed on a material-by-material basis. Safety data sheets are rarely available for (new) nanomaterials, and even when they are, they often lack nano-specific information. Exposure estimations or measurements are difficult to perform and require sophisticated and expensive equipment and personal expertise. The use of banding-based risk assessment tools for laboratory environments is an efficient way to evaluate the occupational risks associated with nanomaterials. Herein, we present an updated version of our risk assessment tool for working with nanomaterials based on a three-step control banding approach and the precautionary principle. The first step is to determine the hazard band of the nanomaterial. A decision tree allows the assignment of the material to one of three bands based on known or expected effects on human health. In the second step, the work exposure is evaluated and the processes are classified into three "nano" levels for each specific hazard band. The work exposure is estimated using a laboratory exposure model. The result of this calculation in combination with recommended occupational exposure limits (rOEL) for nanomaterials and an additional safety factor gives the final "nano" level. Finally, we update the technical, organizational, and personal protective measures to allow nanomaterial processes to be established in research environments.

Chronic exposure to metal fume PM2.5 on inflammation and stress hormone cortisol in shipyard workers: A repeat measurement study.

Particulate matter with an aerodynamic diameter of ≤ 2.5 µm (PM2.5) has been linked to adverse health outcomes in welding workers. The objective of this study was to investigate associations of chronic exposure to metal fume PM2.5 in shipyard workers with health outcomes. A longitudinal study was conducted to determine the effects of metal fume PM2.5 on FeNO, urinary metals, urinary oxidative stress, inflammation, and stress hormones in workers. There were 20 office workers and 49 welding workers enrolled in this study who were followed-up for a second year. We observed that Fe, Zn, and Mn were abundant in PM2.5 to which welding workers were personally exposed, whereas PM2.5 to which office workers were personally exposed was dominated by Pb, Cu, and Zn. We observed in the first and/or second visits that urinary 8-iso-prostaglandin F2-α (PGF2α) and 8-hydroxy-2'-deoxy guanosine (8-OHdG) were significantly increased by exposure. An increase in urinary interleukin (IL)-6 and decreases in urinary serotonin and cortisol were observed in the first and/or second visits after exposure. PM2.5 was associated with decreases in urinary 8-OHdG and cortisol among workers. Next, we observed that urinary Ni, Co, and Fe had significantly increased among workers after a year of exposure. Urinary metals were associated with decreases in urinary 8-iso-PGF2α and cortisol among workers. Urinary Ni, Cu, and Fe levels were associated with an increase in urinary IL-6 and a decrease in urinary cortisol among workers. In conclusion, chronic exposure to metal fume PM2.5 was associated with inflammation and a cortisol deficiency in shipyard workers, which could associate with adrenal glands dysfunction.

Improving Quality in Nanoparticle-Induced Cytotoxicity Testing by a Tiered Inter-Laboratory Comparison Study.

The quality and relevance of nanosafety studies constitute major challenges to ensure their key role as a supporting tool in sustainable innovation, and subsequent competitive economic advantage. However, the number of apparently contradictory and inconclusive research results has increased in the past few years, indicating the need to introduce harmonized protocols and good practices in the nanosafety research community. Therefore, we aimed to evaluate if best-practice training and inter-laboratory comparison (ILC) of performance of the 3-(4,5-dimethylthiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium (MTS) assay for the cytotoxicity assessment of nanomaterials among 15 European laboratories can improve quality in nanosafety testing. We used two well-described model nanoparticles, 40-nm carboxylated polystyrene (PS-COOH) and 50-nm amino-modified polystyrene (PS-NH2). We followed a tiered approach using well-developed standard operating procedures (SOPs) and sharing the same cells, serum and nanoparticles. We started with determination of the cell growth rate (tier 1), followed by a method transfer phase, in which all laboratories performed the first ILC on the MTS assay (tier 2). Based on the outcome of tier 2 and a survey of laboratory practices, specific training was organized, and the MTS assay SOP was refined. This led to largely improved intra- and inter-laboratory reproducibility in tier 3. In addition, we confirmed that PS-COOH and PS-NH2 are suitable negative and positive control nanoparticles, respectively, to evaluate impact of nanomaterials on cell viability using the MTS assay. Overall, we have demonstrated that the tiered process followed here, with the use of SOPs and representative control nanomaterials, is necessary and makes it possible to achieve good inter-laboratory reproducibility, and therefore high-quality nanotoxicological data.

Estimation of Viral Aerosol Emissions From Simulated Individuals With Asymptomatic to Moderate Coronavirus Disease 2019.

Importance: Individuals with asymptomatic or mild coronavirus disease 2019 (COVID-19) have been reported to frequently transmit the disease even without direct contact. The severe acute respiratory syndrome coronavirus 2 has been found at very high concentrations in swab and sputum samples from such individuals. Objective: To estimate the virus levels released from individuals with asymptomatic to moderate COVID-19 into different aerosol sizes by normal breathing and coughing, and to determine what exposure could result from this in a room shared with such individuals. Design, Setting, and Participants: This mathematical modeling study combined the size-distribution of exhaled breath microdroplets for coughing and normal breathing with viral swab and sputum concentrations as approximation for lung lining liquid to obtain an estimate of emitted virus levels. Viral data were obtained from studies published as of May 20, 2020. The resulting emission data fed a single-compartment model of airborne concentrations in a room of 50 m3, the size of a small office or medical examination room. Main Outcomes and Measures: Modeling was used to estimate the viral load emitted by individuals breathing normally or coughing, and the concentrations expected in the simulated room at different ventilation rates. Results: The mean estimated viral load in microdroplets emitted by simulated individuals while breathing regularly was 0.0000049 copies/cm3, with a range of 0.0000000049 to 0.637 copies/cm3. The corresponding estimates for simulated coughing individuals were a mean of 0.277 copies/cm3 per cough, with a range of 0.000277 to 36 030 copies/cm3 per cough. The estimated concentrations in a room with an individual who was coughing frequently were very high, with a maximum of 7.44 million copies/m3 from an individual who was a high emitter. However, regular breathing from an individual who was a high emitter was modeled to result in lower room concentrations of up to 1248 copies/m3. Conclusions and Relevance: In this modeling study, breathing and coughing were estimated to release large numbers of viruses, ranging from thousands to millions of virus copies per cubic meter in a room with an individual with COVID-19 with a high viral load, depending on ventilation and microdroplet formation process. The estimated infectious risk posed by a person with typical viral load who breathes normally was low. The results suggest that only few people with very high viral load pose an infection risk in poorly ventilated closed environments. These findings suggest that strict respiratory protection may be needed when there is a chance to be in the same small room with an individual, whether symptomatic or not, especially for a prolonged period.

From nano to micrometer size particles - A characterization of airborne cement particles during construction activities.

Although, photocatalytic cement contains nanosized TiO2, a possibly carcinogen, no exposure assessments exist for construction workers. We characterized airborne nanoparticle exposures during construction activities simulated in an exposure chamber. We collected some construction site samples for regular cement in Switzerland and Thailand for comparison. Airborne nanoparticles were characterized using scanning mobility particle sizer (SMPS), portable aerosol spectrometer (PAS), diffusion size classifier (DiSCmini), transmission electron microscopy (TEM), scanning electron microscope energy dispersive X-ray spectroscopy (SEM-EDX), and X-ray diffraction. Bagged photocatalytic cement had 2.0 wt% (GSD ± 0.55) TiO2, while TiO2 in aerosols reached 16.5 wt% (GSD ± 1.72) during bag emptying and 9.7 wt% (GSD ± 1.36) after sweeping. The airborne photocatalytic cement particles were far smaller (approximately 50 nm) compared to regular cement. Cutting blocks made from photocatalytic cement or concrete, resulted in similar amounts of airborne nano TiO2 (2.0 wt% GSD ± 0.57) particles as in bagged material. Both photocatalytic and regular cement had a geometric mean diameter (GMD) < 3.5 µm. Main exposures for Thai workers were during sweeping and Swiss workers during drilling and polishing cement blocks. Targeted nanoparticle exposure assessments are needed as a significantly greater exposure to nano TiO2 were observed than what would have been predicted from the material's nano- TiO2 contents.

Occupational Inhalation Exposures to Nanoparticles at Six Singapore Printing Centers.

Laser printers emit high levels of nanoparticles (PM0.1) during operation. Although it is well established that toners contain multiple engineered nanomaterials (ENMs), little is known about inhalation exposures to these nanoparticles and work practices in printing centers. In this report, we present a comprehensive inhalation exposure assessment of indoor microenvironments at six commercial printing centers in Singapore, the first such assessment outside of the United States, using real-time personal and stationary monitors, time-integrated instrumentation, and multiple analytical methods. Extensive presence of ENMs, including titanium dioxide, iron oxide, and silica, was detected in toners and in airborne particles collected from all six centers studied. We document high transient exposures to emitted nanoparticles (peaks of ∼500 000 particles/cm3, lung-deposited surface area of up to 220 µm2/cm3, and PM0.1 up to 16 µg/m3) with complex PM0.1 chemistry that included 40-60 wt % organic carbon, 10-15 wt % elemental carbon, and 14 wt % trace elements. We also record 271.6-474.9 pmol/mg of Environmental Protection Agency-priority polycyclic aromatic hydrocarbons. These findings highlight the potentially high occupational inhalation exposures to nanoparticles with complex compositions resulting from widespread usage of nano-enabled toners in the printing industry, as well as inadequate ENM-specific exposure control measures in these settings.

Correction to: Particle toxicology and health - where are we?

After the publication of this article [1] it was hihglighted that the number of deaths related to natural disasters was incorrectly reported in the second paragraph of the Hazards from Natural particulates and the evolution of the biosphere section. This correction article shows the correct and incorrect statement. This correction does not change the idea presented in the article that from an evolutionary view point, natural disasters account only for a small fraction of the people on the planet. The original article has been updated.

Effects of short- and long-term exposures to particulate matter on inflammatory marker levels in the general population.

The effect of particulate matter (PM) on health increases with exposure duration but the change from short to longer term is not well studied. We examined the exposure to PM smaller 10 µm (PM10) from short to longer duration and their associations with levels of inflammatory markers in the population-based CoLaus cohort in Lausanne, Switzerland. Baseline and follow-up CoLaus data were used to study the associations between PM10 exposure and inflammatory markers, including the high-sensitivity C-reactive protein (CRP), as well as interleukin 1-beta (IL-1ß), interleukin 6 (IL-6), and tumor-necrosis-factor alpha (TNF-α) using mixed models. Exposure was determined for each participant's home address from hourly air quality simulations at a 5-m resolution. Short-term exposure intervals were 1 day, 1 week, and 1 month prior to the hospital visit (blood withdrawal); long-term exposure intervals were 3 and 6 months prior to the visit. In most time windows, IL-6, IL-1ß, and TNF-α were positively associated with PM10. No significant associations were identified for CRP. Adjusted associations with long-term exposures were stronger and more significant than those for short-term exposures. In stratified models, gender, age, smoking status, and hypertension only led to small modifications in effect estimates, though a few of the estimates for IL-6 and TNF-α became non-significant. In this general adult cohort exposed to relatively low average PM10 levels, clear associations with markers of systemic inflammation were observed. Longer duration of elevated exposure was associated with an exacerbated inflammatory response. This may partially explain the elevated disease risk observed with chronic PM10 exposure. It also suggests that reducing prolonged episodes of high PM exposure may be a strategy to reduce inflammatory risk.

Occupational exposure to inhaled nanoparticles: Are young workers being left in the dust?

OBJECTIVES: Occupational exposure to inhaled nanoparticles (NPs) represents a significant concern for worker health. Adolescent workers may face unique risks for exposure and resulting health effects when compared with adult workers. METHODS: This manuscript discusses key differences in risks for occupational exposures to inhaled NPs and resulting health effects between young workers and adult workers via an examination of both physiological and occupational setting factors. RESULTS: Previous studies document how adolescents often face distinct and unique exposure scenarios to occupational hazards when compared to adults. Moreover, they also face different and unpredictable health effects because biological functions such as detoxification pathways and neurological mechanisms are still developing well into late adolescence. Early exposure also increases the chances of developing long-latency disease earlier in life. Taken together, adolescents' rapid growth and development encompasses highly dynamic and complex processes. An aggravating factor is that these processes do not necessarily fall in line with legal classifications of adulthood, nor with occupational exposure limits created for adult workers. CONCLUSIONS: The differences in exposures and health consequences from NPs on young workers are insufficiently understood. Research is needed to better understand what adolescent-specific mitigation strategies may be most suitable to address these risk factors.

Particle toxicology and health - where are we?

BACKGROUND: Particles and fibres affect human health as a function of their properties such as chemical composition, size and shape but also depending on complex interactions in an organism that occur at various levels between particle uptake and target organ responses. While particulate pollution is one of the leading contributors to the global burden of disease, particles are also increasingly used for medical purposes. Over the past decades we have gained considerable experience in how particle properties and particle-bio interactions are linked to human health. This insight is useful for improved risk management in the case of unwanted health effects but also for developing novel medical therapies. The concepts that help us better understand particles' and fibres' risks include the fate of particles in the body; exposure, dosimetry and dose-metrics and the 5 Bs: bioavailability, biopersistence, bioprocessing, biomodification and bioclearance of (nano)particles. This includes the role of the biomolecule corona, immunity and systemic responses, non-specific effects in the lungs and other body parts, particle effects and the developing body, and the link from the natural environment to human health. The importance of these different concepts for the human health risk depends not only on the properties of the particles and fibres, but is also strongly influenced by production, use and disposal scenarios. CONCLUSIONS: Lessons learned from the past can prove helpful for the future of the field, notably for understanding novel particles and fibres and for defining appropriate risk management and governance approaches.

Methodological, political and legal issues in the assessment of the effects of nanotechnology on human health.

Engineered nanomaterials (ENMs) raise questions among the scientific community and public health authorities about their potential risks to human health. Studying a prospective cohort of workers exposed to ENMs would be considered the gold standard for identifying potential health effects of nanotechnology and confirming the 'no effect' levels derived from cellular and animal models. However, because only small, cross-sectional studies have been conducted in the past 5 years, questions remain about the health risks of ENMs. This essay addresses the scientific, methodological, political and regulatory issues that make epidemiological research in nanotechnology-exposed communities particularly complex. Scientific challenges include the array of physicochemical parameters and ENM production conditions, the lack of universally accepted definitions of ENMs and nanotechnology workers, and the lack of information about modes of action, target organs and likely dose-response functions of ENMs. Standardisation of data collection and harmonisation of research protocols are needed to eliminate misclassification of exposures and health effects. Forming ENM worker cohorts from a combination of smaller cohorts and overcoming selection bias are also challenges. National or international registries for monitoring the exposures and health of ENM workers would be helpful for epidemiological studies, but the creation of such a registry and ENM worker cohorts will require political support and dedicated funding at the national and international levels. Public authorities and health agencies should consider carrying out an ENM awareness campaign to educate and engage all stakeholders and concerned communities in discussion of such a project.

Nano-object Release During Machining of Polymer-Based Nanocomposites Depends on Process Factors and the Type of Nanofiller.

We tested the nanomaterial release from composites during two different mechanical treatment processes, automated drilling and manual sawing. Polyurethane (PU) polymer discs (1-cm thickness and 11-cm diameter) were created using different nanomaterial fillers: multiwall carbon nanotubes (MWCNT), carbon black (CB), silicon dioxide (SiO2), and an unfilled PU control. Drilling generated far more submicron range particles than sawing. In the drilling experiments, none of the tested nanofillers showed a significant influence on particle number concentrations or sizes, except for the PU/MWCNT samples, from which larger particles were released than from control samples. Higher drilling speed and larger drill bit size were associated with higher particle counts. Differences between composites were observed during sawing: PU/CB released higher number concentrations of micro-sized particles compared to reference samples. When sawing PU/SiO2 more nanoparticle agglomerates were observed. Furthermore, polymer fumes were released during sawing experiments, which was attributed to the process heat. For both drilling and sawing, the majority of the aerosolized particles were polymer matrix materials containing nanofillers (or protruding from their surface), as evidenced by electron microscopic analysis. Results suggest that: (i) processes associated with higher energy inputs are more likely to result in higher particle release in terms of number concentration; (ii) nanofillers may alter release processes; and (iii) other types of released particles, in particular polymer fumes from high-temperature processes, must also be considered in occupational exposure and risk assessments.

Air-Liquid Interface Cell Exposures to Nanoparticle Aerosols.

The field of nanomedicine is steadily growing and several nanomedicines are currently approved for clinical use with even more in the pipeline. Yet, while the use of nanotechnology to improve targeted drug delivery to the lungs has received some attention, the use of nanoparticles for inhalation drug delivery has not yet resulted in successful translation to market as compared to intravenous drug delivery. The reasons behind the lack of inhaled nanomedicines approved for clinical use or under preclinical development are unclear, but challenges related to safety are likely to contribute. Although inhalation toxicology studies often begin using animal models, there has been an increase in the development and use of in vitro air-liquid interface (ALI) exposure systems for toxicity testing of engineered nanoparticle aerosols, which will be useful for rapid testing of candidate substances and formulations. This chapter describes an ALI cell exposure assay for measuring toxicological effects, specifically cell viability and oxidative stress, resulting from exposure to aerosols containing nanoparticles.

Airborne engineered nanomaterials in the workplace-a review of release and worker exposure during nanomaterial production and handling processes.

For exposure and risk assessment in occupational settings involving engineered nanomaterials (ENMs), it is important to understand the mechanisms of release and how they are influenced by the ENM, the matrix material, and process characteristics. This review summarizes studies providing ENM release information in occupational settings, during different industrial activities and using various nanomaterials. It also assesses the contextual information - such as the amounts of materials handled, protective measures, and measurement strategies - to understand which release scenarios can result in exposure. High-energy processes such as synthesis, spraying, and machining were associated with the release of large numbers of predominantly small-sized particles. Low-energy processes, including laboratory handling, cleaning, and industrial bagging activities, usually resulted in slight or moderate releases of relatively large agglomerates. The present analysis suggests that process-based release potential can be ranked, thus helping to prioritize release assessments, which is useful for tiered exposure assessment approaches and for guiding the implementation of workplace safety strategies. The contextual information provided in the literature was often insufficient to directly link release to exposure. The studies that did allow an analysis suggested that significant worker exposure might mainly occur when engineering safeguards and personal protection strategies were not carried out as recommended.

A System to Create Stable Nanoparticle Aerosols from Nanopowders.

Nanoparticle aerosols released from nanopowders in workplaces are associated with human exposure and health risks. We developed a novel system, requiring minimal amounts of test materials (min. 200 mg), for studying powder aerosolization behavior and aerosol properties. The aerosolization procedure follows the concept of the fluidized-bed process, but occurs in the modified volume of a V-shaped aerosol generator. The airborne particle number concentration is adjustable by controlling the air flow rate. The system supplied stable aerosol generation rates and particle size distributions over long periods (0.5-2 hr and possibly longer), which are important, for example, to study aerosol behavior, but also for toxicological studies. Strict adherence to the operating procedures during the aerosolization experiments ensures the generation of reproducible test results. The critical steps in the standard protocol are the preparation of the material and setup, and the aerosolization operations themselves. The system can be used for experiments requiring stable aerosol concentrations and may also be an alternative method for testing dustiness. The controlled aerosolization made possible with this setup occurs using energy inputs (may be characterized by aerosolization air velocity) that are within the ranges commonly found in occupational environments where nanomaterial powders are handled. This setup and its operating protocol are thus helpful for human exposure and risk assessment.

Increase in oxidative stress levels following welding fume inhalation: a controlled human exposure study.

BACKGROUND: Tungsten inert gas (TIG) welding represents one of the most widely used metal joining processes in industry. It has been shown to generate a large majority of particles at the nanoscale and to have low mass emission rates when compared to other types of welding. Despite evidence that TIG fume particles may produce reactive oxygen species (ROS), limited data is available for the time course changes of particle-associated oxidative stress in exposed TIG welders. METHODS: Twenty non-smoking male welding apprentices were exposed to TIG welding fumes for 60 min under controlled, well-ventilated settings. Exhaled breathe condensate (EBC), blood and urine were collected before exposure, immediately after exposure, 1 h and 3 h post exposure. Volunteers participated in a control day to account for oxidative stress fluctuations due to circadian rhythm. Biological liquids were assessed for total reducing capacity, hydrogen peroxide (H2O2), malondialdehyde (MDA), and 8-hydroxy-2'-deoxyguanosine (8-OHdG) concentrations at each time point. A linear mixed model was used to assess within day and between day differences. RESULTS: Significant increases in the measured biomarkers were found at 3 h post exposure. At 3 h post exposure, we found a 24 % increase in plasma-H2O2 concentrations ([95%CI: 4 % to 46 %], p = 0.01); a 91 % increase in urinary-H2O2 ([2 % to 258 %], p = 0.04); a 14 % increase in plasma-8-OHdG ([0 % to 31 %], p = 0.049); and a 45 % increase in urinary-8-OHdG ([3 % to 105 %], p = 0.03). Doubling particle number concentration (PNC) exposure was associated with a 22 % increase of plasma-8-OHdG at 3 h post exposure (p = 0.01). CONCLUSION: A 60-min exposure to TIG welding fume in a controlled, well-ventilated setting induced acute oxidative stress at 3 h post exposure in healthy, non-smoking apprentice welders not chronically exposed to welding fumes. As mass concentration of TIG welding fume particles is very low when compared to other types of welding, it is recommended that additional exposure metrics such as PNC are considered for occupational risk assessments. Our findings highlight the importance of increasing awareness of TIG welding fume toxicity, especially given the realities of welding workplaces that may lack ventilation; and beliefs among interviewed welders that TIG represents a cleaner and safer welding process.

Characterization of Tungsten Inert Gas (TIG) Welding Fume Generated by Apprentice Welders.

Tungsten inert gas welding (TIG) represents one of the most widely used metal joining processes in industry. Its propensity to generate a greater portion of welding fume particles at the nanoscale poses a potential occupational health hazard for workers. However, current literature lacks comprehensive characterization of TIG welding fume particles. Even less is known about welding fumes generated by welding apprentices with little experience in welding. We characterized TIG welding fume generated by apprentice welders (N = 20) in a ventilated exposure cabin. Exposure assessment was conducted for each apprentice welder at the breathing zone (BZ) inside of the welding helmet and at a near-field (NF) location, 60cm away from the welding task. We characterized particulate matter (PM4), particle number concentration and particle size, particle morphology, chemical composition, reactive oxygen species (ROS) production potential, and gaseous components. The mean particle number concentration at the BZ was 1.69E+06 particles cm(-3), with a mean geometric mean diameter of 45nm. On average across all subjects, 92% of the particle counts at the BZ were below 100nm. We observed elevated concentrations of tungsten, which was most likely due to electrode consumption. Mean ROS production potential of TIG welding fumes at the BZ exceeded average concentrations previously found in traffic-polluted air. Furthermore, ROS production potential was significantly higher for apprentices that burned their metal during their welding task. We recommend that future exposure assessments take into consideration welding performance as a potential exposure modifier for apprentice welders or welders with minimal training.