Towards Tailored Dialdehyde Cellulose Derivatives: A Strategy for Tuning the Glass Transition Temperature.

The derivatization of dialdehyde cellulose (DAC) has received increasing attention in the development of sustainable thermoplastics. In this study, a series of dialcohol celluloses were generated by borohydride reduction, which exhibited glass transition temperature (Tg ) values ranging from 23 to 109 °C, depending on the initial degree of oxidation (DO) of the DAC intermediate. However, the DAC derivatives did not exhibit thermoplastic behavior when the DO of the modified DAC was below 26 %. The influence of introduced side chains was highlighted by comparing DAC-based thermoplastic materials obtained by either oximation or borohydride reduction. Our results provide insights into the generation of DAC-based thermoplastics and highlight a strategy for tailoring the Tg by adjusting the DO during the periodate oxidation step and selecting appropriate substituents in subsequent modifications.

Debugging periodate oxidation of cellulose: Why following the common protocol of quenching excess periodate with glycol is a bad idea.

Periodate oxidation of cellulose to produce "dialdehyde cellulose" (DAC) has lately received increasing attention in sustainable materials development. Despite the longstanding research interest and numerous reported studies, there is still an enormous variation in the proposed preparation and work-up protocols. This apparently reduces comparability and causes reproducibility problems in DAC research. Two simple but prevalent work-up protocols, namely glycol quenching and filtration/washing, were critically examined and compared, resulting in this cautionary note. Various analytical techniques were applied to quantify residual iodine species and organic contaminations from quenching side reactions. The commonly practiced glycol addition cannot remove all oxidising iodine compounds. Both glycol and the formed formaldehyde are incorporated into DAC's polymeric structure. Quenching of excess periodate with glycol can thus clearly be discouraged. Instead, simple washing protocols are recommended which do not bear the risk of side reactions with organic contaminants. While simple washing was sufficient for mildly oxidised celluloses, higher oxidised samples were more likely to trap residual (per)iodate, as determined by thiosulfate titration. For work-up, simple washing with water is proposed while determining potential iodine contaminations after washing with a simple colorimetric test and, if needed, removal of residual periodate by washing with an aqueous sodium thiosulfate solution.

Reductive Amination of Dialdehyde Cellulose: Access to Renewable Thermoplastics.

The reductive amination of dialdehyde cellulose (DAC) with 2-picoline borane was investigated for its applicability in the generation of bioderived thermoplastics. Five primary amines, both aliphatic and aromatic, were introduced to the cellulose backbone. The influences of the side chains on the course of the reaction were examined by various analytical techniques with microcrystalline cellulose as a model compound. The obtained insights were transferred to a 39%-oxidized softwood kraft pulp to study the thermal properties of thereby generated high-molecular-weight thermoplastics. The number-average molecular weights (Mn) of the diamine celluloses, ranging from 60 to 82 kD, were investigated by gel permeation chromatography. The diamine celluloses exhibited glass transition temperatures (Tg) from 71 to 112 °C and were stable at high temperatures. Diamine cellulose generated from aniline and DAC showed the highest conversion, the highest Tg (112 °C), and a narrow molecular weight distribution (D̵ of 1.30).

Fourier transform and near infrared dataset of dialdehyde celluloses used to determine the degree of oxidation with chemometric analysis.

This dataset is related to the research article entitled ``A fast method to measure the degree of oxidation of dialdehyde celluloses using multivariate calibration and infrared spectroscopy''. In this article, 74 dialdehyde cellulose samples with different degrees of oxidation were prepared by periodate oxidation and analysed by Fourier-transform infrared (FTIR) and near-infrared spectroscopy (NIR). The corresponding degrees of oxidation were determined indirectly by periodate consumption using UV spectroscopy at 222 nm and by the quantitative reaction with hydroxylamine hydrochloride followed by potentiometric titration. Partial least squares regression (PLSR) was used to correlate the infrared data with the corresponding degree of oxidation (DO). The developed NIR/PLSR and FTIR/PLSR models can easily be implemented in other laboratories to quickly and reliably predict the degree of oxidation of dialdehyde celluloses.

A fast method to measure the degree of oxidation of dialdehyde celluloses using multivariate calibration and infrared spectroscopy.

The properties of dialdehyde celluloses, which are usually generated by periodate oxidation, are highly dependent on the aldehyde content, i.e. the degree of oxidation (DO). Thus far, the established methods for determining the DO in dialdehyde celluloses lack simplicity or sufficient speed. More than 60 dialdehyde cellulose samples with varying aldehyde content were analysed by near-infrared and Fourier-transform infrared spectroscopy. This was found to be a reliable method for quickly predicting the DO if combined with partial least squares regression (PLSR). The proposed PLSR models can predict the DO with a high determination coefficient (R2) of 99% when applied to a single pulp type and 94% when applied to multiple types. This new approach quickly and reliably determines the DO of dialdehyde celluloses. It can be easily implemented in everyday research to save money, time and resources, especially because the raw datasets and measured DO values are provided.

Time-triggered calcium ion bridging in preparation of films of oxidized microfibrillated cellulose and pulp.

One of the main trends in developing bio-based materials is to improve their mechanical and physical properties using MFC derived from sustainable natural sources and compatible low-cost chemicals. The strength of anionic MFC based materials can be increased with addition of multivalent cations. However, direct mixing of solutions of multivalent cations with oxidized MFC may result in immediate, uncontrollable fibril aggregation and flock formation. The aim of this study was to design a method where Ca2+ ions liberate from solid CaCO3 particles on bleached hardwood (birch) kraft pulp, which was mixed with oxidized MFC and crosslink it to tailor the mechanical properties of the dried structure. In few minutes after adding acetic anhydride, pH of the wet film dropped from 7.3-4.8 through liberation of acetic acid and CaCO3 particles solubilized releasing Ca2+. The novel method could be applied on industrial scale for improving the performance of packaging materials.