Metal-doped niobate pyrochlores and double-perovskites for glycerol valorization: structural and electronic properties and DFT calculations.

In this study, metal-doped niobates and perovskites were obtained by a solid-state reaction. The solids were evaluated in the esterification of glycerol in the presence of acetic acid to produce valuable esters of glycerol. The structural features of the solids indicated the ZnNb2O6, Pb2.8Nb2O7.8 and CuNb2O6 columbite main phases and La2MnFeO6 double-perovskite. Density functional theory (DFT) studies of Pb2.8Nb2O7.8 clearly confirmed the existence of a robust orthorhombic structure and its electronic properties were correlated with the Nb and Pb interactions. The morphological and elemental analyses also indicated that not all surface elements, as well as morphology, were crucial for catalytic properties. All solids were active and selective toward triacetin formation upon glycerol esterification with acetic acid. The catalytic performance depends mainly on the availability of the surface and its structural stability, as well as defects formation. Recyclability studies indicated that the La2MnFeO6 double-perovskite was an efficient catalyst, achieving glycerol conversion of 68% and triacetin selectivity of 25% up to 4 cycles of use in the reaction. The structural defects near the Mn4+/Mn3+ surface sites resulted in the diffusion of anions and an increased concentration of oxygen vacancies contributed to the stable performance of the solid in glycerol ester production.

Ni-Doped Ordered Nanoporous Carbon Prepared from Chestnut Wood Tannins for the Removal and Photocatalytic Degradation of Methylene Blue.

In this work, Ni-doped ordered nanoporous carbon was prepared by a simple and green one-pot solvent evaporation induced self-assembly process, where chestnut wood tannins were used as a precursor, Pluronic® F-127 as a soft template, and Ni2+ as a crosslinking agent and catalytic component. The prepared carbon exhibited a 2D hexagonally ordered nanorod array mesoporous structure with an average pore diameter of ~5 nm. Nickel was found to be present on the surface of nanoporous carbon in the form of nickel oxide, nickel hydroxide, and metallic nickel. Nickel nanoparticles, with an average size of 13.1 nm, were well dispersed on the carbon surface. The synthesized carbon was then tested for the removal of methylene blue under different conditions. It was found that the amount of methylene blue removed increased with increasing pH and concentration of carbon but decreased with increasing concentration of methylene blue. Furthermore, photocatalytic tests carried out under visible light illumination showed that purple light had the greatest effect on the methylene blue adsorption/degradation, with the maximum percent degradation achieved at ~4 h illumination time, and that the percent degradation at lower concentrations of methylene blue was much higher than that at higher concentrations. The adsorption/degradation process exhibited pseudo second-order kinetics and strong initial adsorption, and the prepared carbon showed high magnetic properties and good recyclability.

Correction: Carmo et al. Effects of the Incorporation of Distinct Cations in Titanate Nanotubes on the Catalytic Activity in NOx Conversion. Materials 2021, 14, 2181.

In the original publication, there was a mistake in Figure 1 as published [...].

Effect of Polyvinyl Alcohol Ligands on Supported Gold Nano-Catalysts: Morphological and Kinetics Studies.

The effect of polyvinyl alcohol (PVA) stabilizers and gold nanoparticles supported on active carbon (AuNPs/AC) was investigated in this article. Polymers with different molecular weights and hydrolysis degrees have been synthesized and used, like the stabilizing agent of Au nano-catalysts obtained by the sol-immobilization method. The reduction of 4-nitrophenol with NaBH4 has been used as a model reaction to investigate the catalytic activity of synthesized Au/AC catalysts. In addition, we report several characterization techniques such as ultraviolet-visible spectroscopy (UV-Vis), dynamic light scattering (DLS), X-ray diffraction (XRD), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) in order to correlate the properties of the polymer with the metal nanoparticle size and the catalytic activity. A volcano plot was observed linking the catalytic performance with hydrolysis degree and the maximum of the curve was identified at a value of 60%. The Au:PVA-60 weight ratio was changed in order to explain how the amount of the polymer can influence catalytic properties. The effect of nitroaromatic ring substituents on the catalytic mechanism was examined by the Hammett theory. Moreover, the reusability of the catalyst was investigated, with little to no decrease in activity observed over five catalytic cycles. Morphological and kinetic studies reported in this paper reveal the effect of the PVA polymeric stabilizer properties on the size and catalytic activity of supported gold nanoparticles.

Effects of the Incorporation of Distinct Cations in Titanate Nanotubes on the Catalytic Activity in NOx Conversion.

Effects of the incorporation of Cr, Ni, Co, Ag, Al, Ni and Pt cations in titanate nanotubes (NTs) were examined on the NOx conversion. The structural and morphological characterizations evidenced that the ion-exchange reaction of Cr, Co, Ni and Al ions with the NTs produced catalysts with metals included in the interlayer regions of the trititanate NTs whereas an assembly of Ag and Pt nanoparticles were either on the nanotubes surface or inner diameters through an impregnation process. Understanding the role of the different metal cations intercalated or supported on the nanotubes, the optimal selective catalytic reduction of NOx by CO reaction (SCR) conditions was investigated by carrying out variations in the reaction temperature, SO2 and H2O poisoning and long-term stability runs. Pt nanoparticles on the NTs exhibited superior activity compared to the Cr, Co and Al intercalated in the nanotubes and even to the Ag and Ni counterparts. Resistance against SO2 poisoning was low on NiNT due to the trititanate phase transformation into TiO2 and also to sulfur deposits on Ni sites. However, the interaction between Pt2+ from PtOx and Ti4+ in the NTs favored the adsorption of both NOx and CO enhancing the catalytic performance.

Mechanistic insights into acetaminophen removal on cashew nut shell biomass-derived activated carbons.

Activated carbons prepared from cashew nut shells by chemical activation with phosphoric acid were tested for the removal of acetaminophen. It was found that an increase in carbonization temperature resulted in increased pore volume and decreased amount of surface functional groups. Potentiometric titration analysis indicated that the majority of surface groups on carbons are acidic. Detailed surface characterization by FT-IR, XPS, and thermal analyses indicated the involvement of surface functional groups in the removal of acetaminophen either via hydrogen bonding or by acid hydrolysis. The carbon obtained at 600 °C, which contains high amount of carboxylic groups and high pore volume, exhibited the highest adsorption capacity. For this carbon, the removal of acetaminophen took place mostly via acid hydrolysis with the formation of p-aminophenol and acetic acid adsorbed on the surface. Carbon obtained at 400 °C was found to have the highest density of acidic functional groups, which resulted in dimerization reactions and pore blockage. No direct correlation was observed between the adsorption capacities of carbons and their textural or surface characteristics. This suggests the complexity of acetaminophen removal by the cashew nut shell-derived activated carbons, governed by their surface chemistry and supported by high surface area accessible via micro/mesopores.

Acid Red 66 Dye Removal from Aqueous Solution by Fe/C-based Composites: Adsorption, Kinetics and Thermodynamic Studies.

The presence of synthetic dyes in water causes serious environmental issues owing to the low water quality, toxicity to environment and human carcinogenic effects. Adsorption has emerged as simple and environmental benign processes for wastewater treatment. This work reports the use of porous Fe-based composites as adsorbents for Acid Red 66 dye removal in an aqueous solution. The porous FeC and Fe/FeC solids were prepared by hydrothermal methods using iron sulfates and sucrose as precursors. The physicochemical properties of the solids were evaluated through X-ray diffraction (XRD), Scanning electron microscopy coupled with Energy dispersive spectroscopy (SEM-EDS), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared s (FTIR), Raman and Mössbauer spectroscopies, nitrogen adsorption-desorption isotherms, Electron Paramagnetic Resonance (EPR) and magnetic saturation techniques. Results indicated that the Fe species holds magnetic properties and formed well dispersed Fe3O4 nanoparticles on a carbon layer in FeC nanocomposite. Adding iron to the previous solid resulted in the formation of γ-Fe2O3 coating on the FeC type structure as in Fe/FeC composite. The highest dye adsorption capacity was 15.5 mg·g-1 for FeC nanocomposite at 25 °C with the isotherms fitting well with the Langmuir model. The removal efficiency of 98.4% was obtained with a pristine Fe sample under similar experimental conditions.

Design of Multifunctional Titania-Based Photocatalysts by Controlled Redox Reactions.

This work aims at the preparation of multifunctional titania-based photocatalysts with inherent capabilities for thermal co-activation and stabilisation of anatase polymorph, by designing the phase composition and microstructure of rutile-silicon carbide mixture. The processing involved a conventional solid state route, including partial pre-reduction of rutile by SiC in inert Ar atmosphere, followed by post-oxidation in air. The impacts of processing conditions on the phase composition and photocatalytic activity were evaluated using Taguchi planning. The XRD studies confirmed the presence of rutile/anatase mixtures in the post-oxidised samples. The results emphasise that pre-reduction and post-oxidation temperatures are critical in defining the phase composition, while post-oxidation time is relevant for the photocatalytic performance. Microstructural studies revealed the formation of core-shell particles, which can suppress the photocatalytic activity. The highest apparent reaction rate of the photodegradation of methylene blue was observed for the sample pre-reduced in Ar at 1300 °C for 5 h and then calcined in air at 400 °C for 25 h. Though its performance was ~1.6-times lower than that for the same amount of nanostructured industrial P25 photocatalyst, it was achieved in the material possessing 2-3 times lower surface area and containing ~50 mol% of SiO2 and SiC, thus demonstrating excellent prospects for further improvements.

Photocatalyzed preferential oxidation of CO under simulated sunlight using Au-transition metal oxide-sepiolite catalysts.

In the present study a series of Au-transition metal oxides supported on a clay mineral such as sepiolite were tested in the preferential oxidation of CO in an excess of H2 under simulated solar light irradiation and in the absence of light, at 30 °C and atmospheric pressure. Transition metal oxides (ZnO, Fe2O3, NiO, MnO2, and Co3O4) were dispersed over the sepiolite surface where, subsequently, Au nanoparticles with an average particle size between 2 and 3 nm were successfully deposited-precipitated. The obtained photocatalysts were characterized by XRD, XRF, DRUV-Vis, N2 adsorption-desorption and HRTEM in order to evaluate the optical, structural and chemical properties of the prepared samples. Despite the low amount of gold (nominal 1.0 wt%), the catalysts exhibited an outstanding behavior under light irradiation, with reaction rates between 4.5 and 5.2 mmol COox gcat-1 h-1 for the Au-NiSep, Au-CoSep and Au-ZnSep samples. These photocatalysts exhibited a high dispersion of the respective transition metal oxides over the sepiolite support and the presence of low-coordinated hemispherical gold nanoparticles. The superior photocatalytic efficiency of these samples was ascribed to the reduction of the electron-hole pair recombination of photogenerated charge carriers by the excitation of the localized surface plasmon resonance of the Au nanoparticles. The BET surface area and the gold particle size seemed to be relevant factors affecting the catalytic performance.

Chitosan activated with divinyl sulfone: a new heterofunctional support for enzyme immobilization. Application in the immobilization of lipase B from Candida antarctica.

A novel heterofunctional support for enzyme immobilization, chitosan-divinyl sulfone, was assessed in this study. The activation of chitosan with DVS was carried out at three different pHs (10.0, 12.5 and 14.0) and a Candida antarctica Lipase B (CALB) was selected as the model enzyme. After immobilization, the biocatalysts were incubated under alkaline conditions in a buffer to facilitate the multipoint covalent attachment, followed by incubation in ethylenediamine (EDA) aiming at blocking the remaining reactive groups. The highest thermal stability was obtained when pH 10.0 was used during support activation. These results were shown to be better than those obtained when using glutaraldehyde as the support-activating reagent. Subsequently, the immobilization pH was investigated (5.0, 7.0 and 10.0) prior to alkaline incubation, with the highest enzyme stability levels found at pH 10.0. Finally, the selected biocatalyst was used in the hydrolysis of ethyl hexanoate and presented an activity of 14,520.37 U/g of immobilized lipase at pH 5.0. These results show that chitosan activated with divinyl sulfone is a very promising support for enzyme immobilization and the proposed protocol is able to successfully improve enzyme stability.

CO Preferential Photo-Oxidation in Excess of Hydrogen in Dark and Simulated Solar Light Irradiation over AuCu-Based Catalysts on SBA-15 Mesoporous Silica-Titania.

In this work, SBA-15 silica and silica-titania have been used as supports for photocatalysts based on AuCu alloy (Au:Cu = 1) to be used in the preferential oxidation of CO (CO-PROX) in excess of hydrogen at room temperature and atmospheric pressure both in the dark and under simulated solar light irradiation. To study their textural, structural, chemical and optical properties, the samples were characterized by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HR-TEM), adsorption-desorption of N2 at -196 °C, 13C and 29Si solid state nuclear magnetic resonance (NMR), X-ray photoelectron spectroscopy (XPS) and diffuse reflectance ultraviolet-visible (DRUV-vis) spectroscopy. Titanium was present mainly in the form of titania aggregates, but also as small particles interacting with the SBA support. In both catalysts, the metal alloy nanoparticles displayed an average size of 4 nm as demonstrated by TEM measurements. AuCu/Ti-SBA turned out to be photoactive and selective in the photo-CO-PROX reaction showing the highest activity, with conversion and selectivity towards CO2 of 80%, due both to the presence of titania incorporated in SBA-15 and to the synergistic effect of Cu when alloyed with Au.

Lamellar zirconium phosphates to host metals for catalytic purposes.

In the present study a porous lamellar zirconium phosphate heterostructure (PPH) formed from zirconium(iv) phosphate expanded with silica galleries (P/Zr molar ratio equal to 2 and (Si + Zr)/P equal to 3) was prepared to host noble metals. Textural and structural characterization of PPH-noble metal materials was carried out in order to elucidate the location and dispersion of the metallic particles and the properties of the resulting material to be used in catalytic processes. In the present paper, their activity in the catalytic hydrodeoxygenation (HDO) reaction of dibenzofuran (DBF) was evaluated. X-ray diffraction (XRD), solid state nuclear magnetic resonance (NMR) and X-ray photoelectron spectroscopy (XPS) evidenced that the structure of the pillared zirconium phosphate material was not modified by the incorporation of Pt and Pd. Moreover, transmission electron microscopy (TEM) showed a different dispersion of the noble metal. The acidity of the resulting PPH-noble metal materials also changed, although in all cases the acidity was of weak nature, and the incorporation of noble metals affected Brønsted acid sites as observed from 31P NMR spectra. In general, the textural, structural and acidic properties of the resulting materials suggest that PPH can be considered a good candidate to be used as a catalytic support. Thus, the catalytic results of the PPH-noble metal samples indicated that the Pd sample showed a stable behavior probably ascribed to a high dispersion of the active phase. However, the Pt sample suffered from fast deactivation. The selectivity to the reaction products was strongly dependent on the noble metal employed.