RESUMEN
Solid-state batteries based on Li7La3Zr2O12 (LLZO) garnet electrolyte are a robust and safe alternative to conventional lithium-ion batteries. However, the large-scale implementation of ceramic composite cathodes is still challenging due to a complex multistep manufacturing process. A new one-step route for the direct synthesis of LLZO during the manufacturing of LLZO/LiCoO2 (LCO) composite cathodes based on cheap precursors and utilizing the industrially established tape casting process is presented. It is shown that Al, Ta:LLZO can be formed directly in the presence of LCO from metal oxide precursors (LiOH, La2O3, ZrO2, Al2O3, and Ta2O5) by heating to 1050 °C, eliminating the time- and energy-consuming synthesis of preformed LLZO powders. In addition, performance-optimized gradient microstructures can be produced by sequential casting of slurries with different compositions, resulting in dense and flat phase-pure cathodes without unwanted ion interdiffusion or secondary phase formation. Freestanding cathodes with a thickness of 85 µm, a relative density of 95%, and an industrial relevant LCO loading of 15 mg show an initial capacity of 82 mAh g-1 (63% of the theoretical capacity of LCO) in a solid-state cell with Li metal anodes, which is comparable to conventional LCO/LLZO cathodes and can be further improved in the future.
RESUMEN
In this work, the effects of dopant size and oxidation state on the structure and electrochemical performance of LiNi0.8Co0.1Mn0.1O2 (NCM811) are investigated. It is shown that doping with boron (B) which has a small ionic radius and an oxidation state of 3+, leads to the formation of a boron oxide-containing surface coating (probably Li3BO3), mainly on the outer surface of the secondary particles. Due to this effect, boron only slightly affects the size of the primary particle and the initial capacity, but significantly improves the capacity retention. On the other hand, the dopant ruthenium (Ru) with a larger ionic radius and a higher oxidation state of 5+ can be stabilized within the secondary particles and does not experience a segregation to the outer agglomerate surface. However, the Ru dopant preferentially occupies incoherent grain boundary sites, resulting in smaller primary particle size and initial capacity than for the B-doped and pristine NCM811. This work demonstrates that a small percentage of dopant (2 mol%) cannot significantly affect bulk properties, but it can strongly influence the surface and/or grain boundary properties of microstructure and thus the overall performance of cathode materials.
RESUMEN
Non-toxic, highly active and robust complexes are the holy grail as ideal green catalysts for the polymerisation of biorenewable and biodegradable polylactide. Four new zinc guanidine complexes [ZnCl2(TMG4NMe2asme)], [ZnCl2(TMG5Clasme)], [ZnCl2(TMG5Measme)] and [ZnCl2(TMG5NMe2asme)] with different electron-donating and electron-withdrawing groups on the ligand's aromatic backbone have been synthesised. Ligands are derived from low-cost commercially available compounds and have been converted by a three- or four-step synthesis process into the desired ligand in good yields. The compounds have been fully characterised and tested in the ROP of rac-LA under industrially relevant conditions. The complexes are based on the recently published structure [ZnCl2(TMGasme)] which has shown high activity in the polymerisation of lactide at 150 °C. Different substituents in the para-position of the guanidine moiety significantly increase the polymerisation rate whereas positioning substituents in the meta-position causes no change in the reaction rate. With molecular weights over 71 000 g mol-1 being achievable, the best system produces polymers for multiple industrial applications and its polymerisation rate approaches that of Sn(Oct)2. The robust systems are able to polymerise non-purified lactide. The initiation of the polymerisation is suggested to occur due to impurities in the monomer.