RESUMEN
A slurry sampling method was developed for the fast determination of Pb, Ni, Fe, and Mn in construction materials by high-resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GFAAS). For sample introduction into the GF, stable slurries were prepared by sonicating 10 mg of ground solid sample in 10.0 mL of 1% (v/v) Triton X-100 and 1% (v/v) HNO3 solution for 1.0 min. The determination of the four elements was carried out in three measurement runs, with Ni and Fe being determined simultaneously. The HR-CS GFAAS measurements were performed using analytical lines with adequate sensitivity, considering the content of each element in the material: Pb at 283.306 nm (42%), Mn at 403.080 nm (6.7%), Ni at 232.003 nm (100%) and Fe at 232.036 nm (1.4%). The pyrolysis and atomization temperatures and the use of chemical modifiers were optimized using both aqueous standards and slurry samples. At optimal conditions, samples with concentrations of Pb from 1.5 to 80 µg g-1, Ni from 4.0 to 75 µg g-1, Mn from 2.0 to 600 µg g-1, and Fe from 0.15 to 60 mg g-1 could be determined using a unique sample suspension. To assess the validity of the method, a fly ash certified reference material (CRM) was analysed using the slurry sampling HR-CS GFAAS method; this CRM and the construction material samples were also analysed by HR-CS GFAAS after the digestion of the samples. The obtained results using both methods were statistically comparable (Student's paired t-test for two independent methods at a 95% confidence level) demonstrating the suitability of the proposed method.
RESUMEN
The linear economy paradigm in place to date has to be seriously challenged to give way to a new school of thought known as the circular economy. In this research work, precast kerbs and paving blocks made with recycled concrete (RACC-mixture) bearing 50 wt% mixed recycled aggregate (masonry content of 33%) and an eco-efficient cementitious material as 25 wt% conventional binder replacement were evaluated to assess their intrinsic potential to replace traditional raw materials, in keeping with circular economy criteria. Therefore, precast products were subjected to mechanical strength, durability and microstructure tests and were compared to conventional concrete units (CC-mixture and commercially available precast elements). Although a class demotion was observed for water absorption and some decreases in flexural strength (26%), splitting tensile strength (12.8%) and electrical resistivity (45%) and a lower class water absorption were registered, and the recycled mixture also exhibited a greater performance in terms of compressive strength (6%), a better abrasion resistance classification and a comparable porosity and microstructure, which ensures a good concrete durability. In any case, the results showed that precast pieces were European standard-compliant, thus supporting the viability of the mixed recycled aggregates and eco-efficient cementitious replacement in footways.
RESUMEN
This study explores the effect on sulfate resistance of the use of ornamental granite industry waste as a supplementary cementitious material (at replacement ratios of 10% and 20%) in cement manufacture. The present paucity of scientific knowledge of the behaviour of these new cements when exposed to an external source of sulfates justifies the need for, and the originality of, this research. After characterising the waste chemically and mineralogically, cement paste specimens were prepared in order to determine the durability of the newly designed eco-cements using Köch-Steinegger corrosion indices. The new hydration products, which might induce microstructural, mineralogical, or morphological decay in the specimens, were also analysed by comparing the samples before and after soaking in a sodium sulfate solution for different test periods. Respect to the results, the damage to pastes bearing 10% granite sludge (GS) is the same as observed in OPC, whilst the former exhibit a higher Köch-Steinegger corrosion rate (1.61) than both OPC and OPC+20GS. Soaking the pastes in sodium sulfate induces matrix densification due to ettringite formation and gypsum precipitation in the pores. Further to those results, at an optimal replacement ratio of 10%, these alternative, eco-friendlier materials can be used in the design and construction of non-structural cement-based (mortar or concrete) members exposed to an external source of sulfate.