Low-temperature adaptive conductive hydrogel based on ice structuring proteins/CaCl2 anti-freeze system as wearable strain and temperature sensor.

Conductive hydrogels as wearable devices meet the basic demands of mechanical flexibility and smart sensing. However, achieving anti-freeze property in conductive hydrogels is still challengeable. Here, a novel anti-freezing system based on ice structuring proteins and CaCl2 was introduced to enable a conductive hydrogel with low-temperature adaptability. Both formation of ice nuclei and ice growth of the hydrogel at sub-zero temperature could be inhibited. Supported by the anti-freeze system, the hydrogel revealed good flexibility (890% at -20 °C), recovery and conductivity (0.50 S/m at -20 °C) at both room temperature and sub-zero temperature. The low-temperature adaptability enabled the hydrogel to be used as strain and temperature sensors at both room temperature and sub-zero temperature. The anti-freeze system in this work is expected to open up a new avenue to promote the conductive hydrogel with low-temperature adaptability.

Multi-Sacrificial Bonds Enhanced Double Network Hydrogel with High Toughness, Resilience, Damping, and Notch-Insensitivity.

The engineering applications of hydrogels are generally limited by the common problem of their softness and brittlness. In this study, a composite double network ionic hydrogel (CDN-gel) was obtained by the facile visible light triggered polymerization of acrylic acid (AA), polyvinyl alcohol (PVA), and hydrolyzed triethoxyvinylsilane (TEVS) and subsequent salt impregnation. The resulting CDN-gels exhibited high toughness, recovery ability, and notch-insensitivity. The tensile strength, fracture elongation, Young's modulus, and toughness of the CDN-gels reached up to ~21 MPa, ~700%, ~3.5 MPa, and ~48 M/m3, respectively. The residual strain at a strain of 200% was only ~25% after stretch-release of 1000 cycles. These properties will enable greater application of these hydrogel materials, especially for the fatigue resistance of tough hydrogels, as well as broaden their applications in damping.

Porous biochar/chitosan composites for high performance cellulase immobilization by glutaraldehyde.

In this work, porous biochar derived from sugarcane bagasse was prepared and then coated with different amounts of chitosan (C@CS) for cellulase immobilization. Cellulase was covalently immobilized on the support by using glutaraldehyde as a linker. The chemical characteristics and morphology of the samples were determined by SEM, BET, FT-IR and XPS. The properties of immobilized enzyme were evaluated by activity recovery, optimum pH value and temperature, and recyclability. The results showed that all the three kinds of immobilized cellulase did not change the optimum pH value of 4 and temperature of 60 °C, and they also exhibited good activity and reusability. Especially for C@CS25 (the feeding ratio of porous biochar to chitosan was 0.5 g: 25 mg), the support retained the morphology of porous biochar well. The corresponding immobilized cellulase kept 67 % activity of free cellulase at pH = 4 and 60 °C, and showed a glucose productivity of 90.8 % even after 10 cycles.

Thermal Welding by the Third Phase Between Polymers: A Review for Ultrasonic Weld Technology Developments.

Ultrasonic welding (USW) is a promising method for the welds between dissimilar materials. Ultrasonic thermal welding by the third phase (TWTP) method was proposed in combination with the formation of a third phase, which was confirmed as an effective technology for polymer welding between the two dissimilar materials compared with the traditional USW. This review focused on the advances of applying the ultrasonic TWTP for thermoplastic materials. The research development on the ultrasonic TWTP of polycarbonate (PC) and polymethyl methacrylate (PMMA), polylactic acid (PLA) and polyformaldehyde (POM), and PLA and PMMA are summarized according to the preparation of the third phase, welded strength, morphologies of rupture surfaces, thermal stability, and others. The review aimed at providing guidance for using ultrasonic TWTP in polymers and a basic understanding of the welding mechanism, i.e., interdiffusion and molecular motion mechanisms between the phases.

Preparation and Characterization of DOPO-Functionalized MWCNT and Its High Flame-Retardant Performance in Epoxy Nanocomposites.

In this work, functionalized multi-walled carbon nanotubes (MWCNT) were synthesized by the reaction between acylated MWCNT and 10-(2,5-dihydroxyphenyl)-9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (ODOPB). The obtained MWCNT-ODOPB was well dispersed into epoxy resins together with aluminum diethylphosphinate (AlPi) to form flame-retardant nanocomposites. The epoxy resin nanocomposite with phosphorus content of 1.00 wt % met UL 94 V-0 rating, exhibited LOI value of 39.5, and had a higher Tg compared to neat epoxy resin, which indicates its excellent flame retardant performance. These experimental results indicated that MWCNT-ODOPB was a compatible and efficient flame retardant for epoxy resins. Moreover, cone calorimeter analysis showed that the peak heat release rate (pHRR), total heat release (THR) values, and CO2 production profiles of the composites decreased with an increase in the additional amount of phosphorus.

Strain-Sensitive Performance of a Tough and Ink-Writable Polyacrylic Acid Ionic Gel Crosslinked by Carboxymethyl Cellulose.

A tough polyacrylic acid ionic gel is obtained using carboxymethyl cellulose as a crosslinker and KCl as a conductive ions donor. The polymerization process is initiated by ceric ammonium nitrate and triggered by visible light, which can be employed as a facile 3D printing process to fabricate arbitrary gel architectures. Curling macromolecular crosslinker and plentiful hydrogen bonds among polymers endow the ionic gel with superior mechanical performance including high tensile strength (≈1.33 MPa), large elongation (>8 times), high toughness (≈5.11 MJ m-3 ), and good self-recovery property. Importantly, the ionic gel can be assembled into a flexible strain sensor to precisely monitor the diverse human body motions in real time, that is, joints bending and muscle contraction, by recording the capacitance variation. This strain-sensitive performance, which can recover even after 1000 successive cycles, should enable the detection of body action and provide a potential application in health-care monitoring or human-computer user interfaces.

Effects of Isolation by Continental Islands in the Seto Inland Sea, Japan, on Genetic Diversity of the Large Japanese Field Mouse, Apodemus speciosus (Rodentia: Muridae), Inferred from the Mitochondrial Dloop Region.

To study the effects of post-glacial isolation by islands on population genetic diversity and differentiation of the large Japanese field mouse, Apodemus speciosus, we examined partial nucleotide sequences of the mitochondrial Dloop region (ca. 300 bp) in 231 individuals collected from islands in the Seto Inland Sea and adjacent regions on Honshu and Shikoku Islands in the western part of the Japanese archipelago. Molecular phylogenetic and network analyses showed that haplotypes in each island tended to form monophyletic groups, while those in Honshu and Shikoku (the major Japanese islands) showed scattered relationships and were connected with island haplotypes. These observations suggest that a set of Honshu and Shikoku haplotypes became the ancestral lineages of the island population. No gene flow was detected among island populations, indicating that independent evolution occurred on each island, without the influence of human activities, since the establishment of the islands in the Holocene. Population genetic diversities on each island were lower than those on Honshu and Shikoku. Comparison between genetic diversity and island area size showed positive correlations and supported the suggestion that genetic drift is a major factor that shaped the current haplotype constitution of the islands in the Seto Inland Sea.

Rapid Recovery Double Cross-Linking Hydrogel with Stable Mechanical Properties and High Resilience Triggered by Visible Light.

The designed tough hydrogels, depending on energy dissipation mechanism, possess excellent biocompatibility, stimuli-responsiveness, and outstanding mechanical properties. However, the application of hydrogels is greatly limited in actuators and sensors for the lack of instantaneous recovery and resilience. In this work, we synthesized a double cross-linking poly(acrylic acid) hydrogel via a simple, one-pot, visible-light-trigger polymerization, with carboxymethyl cellulose as initiator and the first cross-linker, N,N'-methylene bis(acrylamide) (MBA) as the second cross-linker. The tensile strength and elastic modulus are in the range of 724-352 kPa and 115-307 kPa, respectively, depending on the MBA content. The swelling ratio of hydrogels dramatically decreased with increasing the MBA content. DMA results indicate that the internal friction between molecules within the hydrogel decreases with the increase of MBA content. Cyclic tensile tests show that after the structure stabilizes, the resilience, maximum stress, and residual strain of Gel-2 maintains over 93% (95% for successive cyclic tensile test), 115 kPa and less than 3%, respectively, at a strain of 125%. The values of resilience and residual strain are almost constant in both successive and intermittent cyclic tensile tests. Moreover, the swollen hydrogel has higher resilience and lower residual strain than the same hydrogel in the as-prepared state.

Enhanced Conductivity and Electrochemical Performance of Electrode Material Based on Multifunctional Dye Doped Polypyrrole.

Polypyrrole were prepared via in-situ chemical oxidative polymerization in the presence of multisulfonate acid dye (acid violet 19). In this work, acid violet 19 could play the role as dopant, surfactant and physical cross-linker for pyrrole polymerization, and had impact on the morphology, dispersion stability, thermal stability, electrical conductivity and electrochemical behavior of the samples. The thermal stability of the dye doped polypyrrole was enhanced than pure polypyrrole due to the strong interactions between polypyrrole and acid violet 19. The dispersion stability of the samples in water was also improved by incorporating an appropriate amount of acid violet 19. The sample with 20% of acid violet 19 showed granular morphology with the smallest diameter of -50 nm and possessed the maximum electrical conductivity of 39.09 S/cm. The as-prepared multifunctional dye doped polypyrrole samples were used to fabricate electrodes and exhibited a mass specific capacitance of 379-206 F/g in the current density range of 0.2-1.0 A/g. The results indicated that the multifunctional dye could improve the performances of polypyrrole as electrode material for supercapacitors.

Robust and Superhydrophobic Surface Modification by a "Paint + Adhesive" Method: Applications in Self-Cleaning after Oil Contamination and Oil-Water Separation.

Conventional superhydrophobic surfaces have always depended on expensive, sophisticated, and fragile roughness structures. Therefore, poor robustness has turned into the bottleneck for large-scale industrial applications of the superhydrophobic surfaces. To handle this problem, a superhydrophobic surface with firm robustness urgently needs to be developed. In this work, we created a versatile strategy to fabricate robust, self-cleaning, and superhydrophobic surfaces for both soft and hard substrates. We created an ethanol based suspension of perfluorooctyltriethoxysilane-mdodified calcium carbonate nanoparticles which can be sprayed onto both hard and soft substrates to form superhydrophobic surfaces. For all kinds of substrates, spray adhesive was directly coated onto abluent substrate surfaces to promote the robustness. These superhydrophobic surfaces showed remarkable robustness against knife scratch and sandpaper abrasion, while retaining its superhydrophobicity even after 30 abrasion cycles with sandpaper. What is more, the superhydrophobic surfaces have shown promising potential applications in self-cleaning and oil-water separation. The surfaces retained their self-cleaning property even immersed in oil. In addition to oil-water separation, the water contents in oil after separation of various mixtures were all below 150 ppm, and for toluene even as low as 55 ppm. Furthermore, the as-prepared device for oil-water separation could be cycled 6 times and still retained excellent oil-water separation efficiency.

Preparation and application of conducting polymer/Ag/clay composite nanoparticles formed by in situ UV-induced dispersion polymerization.

In this work, composite nanoparticles containing polypyrrole, silver and attapulgite (PPy/Ag/ATP) were prepared via UV-induced dispersion polymerization of pyrrole using ATP clay as a templet and silver nitrate as photoinitiator. The effects of ATP concentration on morphology, structure and electrical conductivity were studied. The obtained composite nanoparticles with an interesting beads-on-a-string morphology can be obtained in a short time (10 min), which indicates the preparation method is facile and feasible. To explore the potential applications of the prepared PPy/Ag/ATP composite nanoparticles, they were served as multifunctional filler and blended with poly(butylene succinate) (PBS) matrix to prepare biodegradable composite material. The distribution of fillers in polymer matrix and the interfacial interaction between fillers and PBS were confirmed by scanning electron microscope, elemental mapping and dynamic mechanical analysis. The well dispersed fillers in PBS matrix impart outstanding antibacterial property to the biodegradable composite material as well as enhanced storage modulus due to Ag nanoparticles and ATP clay. The biodegradable composite material also possesses modest surface resistivity (10(6)~ 10(9) Ω/◻).

Fundus autofluorescence and optical coherence tomography findings in branch retinal vein occlusion.

Purpose. To describe the findings of fundus autofluorescence (FAF) and optical coherence tomography (OCT) in patients with branch retinal vein occlusion (BRVO). Methods. In this institutional, retrospective, observational case series, FAF was evaluated in 65 eyes with BRVO in 64 consecutive patients and compared with visual acuity, OCT findings, and other clinical observations. Results. Five types of autofluorescence appeared during the course of BRVO: (1) petaloid-shaped hyperautofluorescence in the area of macular edema and (2) hyperautofluorescence coincident with yellow subretinal deposits. (3) Diffuse hyperautofluorescence appeared within the area of serous retinal detachment (SRD) and OCT showed precipitates on the undersurface of the retina in 5/5 of these eyes (100%). (4) The area of vein occlusion showed diffuse hyperautofluorescence after resolution of the retinal bleeding. (5) Hard exudates exhibited hyper- or hypoautofluorescence. OCT indicated that most of the hard exudates with hyperautofluorescence were located on the retinal pigment epithelium. Conclusions. Hyperautofluorescence associated with subretinal fluid or hard exudate appeared in the subretinal space. This type of hyperautofluorescence may be attributed to blood cell or macrophages. FAF and OCT are noninvasive modalities that provide additional information regarding macular edema due to BRVO.

Directional bias of neurons in V1 and V2 of strabismic monkeys: temporal-to-nasal asymmetry?

PURPOSE: Strabismus that develops shortly after birth is known to cause temporal-to-nasal eye movement asymmetries under monocular viewing. The neural mechanisms underlying this deficit are not well understood. In the current study, the hypothesis that this eye movement anomaly reflects a similar asymmetry in the directional response properties of neurons in the early stages of cortical processing was examined. METHODS: Strabismus was simulated with optical methods in infant monkeys between 4 and 14 weeks of age. When the monkeys were mature, microelectrode recording experiments were conducted in the primary visual cortex (V1) and visual area 2 (V2). After the spatial frequency of sine wave-grating stimuli for each neuron was optimized, each neuron's responsiveness to 24 directions of stimulus movement was measured. The preferred direction and the strength of directional bias were determined by a vector summation method: RESULTS: There was not an overabundance of neurons in V1 or V2 of strabismic monkeys preferring the temporal-to-nasal direction of stimulus movement. However, the average directional bias was significantly reduced in these strabismic monkeys. Interocular suppression was highly prevalent, and this suppression was stronger and more common in neurons dominated by the ipsilateral eye. CONCLUSIONS: The results suggest that the eye movement asymmetries in strabismic subjects do not result from similar asymmetries in the directional properties of V1 or V2 neurons, but rather reflect impoverished cortical signals to the brain stem nuclei that control eye movements.

Rapid plasticity of binocular connections in developing monkey visual cortex (V1).

The basic sets of cortical connections are present at birth in the primate visual system. The maintenance and refinement of these innate connections are highly dependent on normal visual experience, and prolonged exposure to binocularly uncorrelated signals early in life severely disrupts the normal development of binocular functions. However, very little is known about how rapidly these changes in the functional organization of primate visual cortex emerge or what are the sequence and the nature of the abnormal neural events that occur immediately after experiencing binocular decorrelation. In this study, we investigated how brief periods of ocular misalignment (strabismus) at the height of the critical period alter the cortical circuits that support binocular vision. After only 3 days of optically imposed strabismus, there was a striking increase in the prevalence of V1 neurons that exhibited binocular suppression, i.e., binocular responses were weaker than monocular responses. However, the sensitivity of these neurons to interocular spatial phase disparity was not significantly altered. These contrasting results suggest that the first significant change in V1 caused by early binocular decorrelation is binocular suppression, and that this suppression originates at a site(s) beyond where binocular signals are initially combined.

Comparison between in situ hybridization and real-time PCR technique as a means of detecting the integrated form of human papillomavirus 16 in cervical neoplasia.

Integration of the human papillomavirus (HPV) genome is thought to be one of the causes of cancer progression. However, there is controversy concerning the physical status of HPV 16 in premalignant cervical lesions, and there have been no reports on the concordance between detection of the integrated form of HPV16 by real-time PCR and by in situ hybridization. We investigated specimens of cervical intraepithelial neoplasia (CIN) and invasive carcinomas for the physical status of HPV 16 by real-time PCR and in situ hybridization. The presence of the integrated form was detected by both real-time PCR and in situ hybridization in zero of four cases of CIN1, three of six cases of CIN2, nine of 27 cases of CIN3, and two of six cases of invasive carcinomas. Integrated HPV 16 was present in some premalignant lesions but was not always present in carcinomas. The concordance rate between the two methods for the detection of the presence of the integrated form was 37 of 43 (86%) cases. Real-time PCR and in situ hybridization were found to be complementary and convenient techniques for determining the physical status of the HPV genome. We conclude that a combination of both methods is a more reliable means of assessing the physical status of the HPV genome in cervical neoplasia.

Dihydropyrimidine dehydrogenase in normal and malignant endometrium: relationship with cell proliferation and thymidine phosphorylase.

Dihydropyrimidine dehydrogenase (DPD) is a pyrimidine salvage enzyme responsible for degradation of thymine, which is produced from thymidine by thymidine phosphorylase (TP). Our purpose was to determine the relationship between DPD, cell proliferation and TP expression in human endometrium. We examined DPD gene expression using reverse transcription-polymerase chain reaction, DPD protein levels using enzyme-linked immunosorbent assay, and DPD protein localization using immunohistochemistry in 58 normal endometria and 28 endometrial cancers. DPD gene expression was then related to the proliferating cell nuclear antigen index and to TP gene expression. DPD gene expression, which was correlated with DPD protein level, was relatively stable throughout various menstrual phases but was significantly elevated in postmenopausal status. It was significantly lower in endometrial cancer than in normal endometrium. Localization analysis revealed that DPD protein was located primarily in epithelial cells, but was also present in stromal cells. DPD gene expression correlated inversely with the PCNA index. TP gene expression pattern contrasted with that of DPD in postmenopausal and malignant endometrium. A high ratio of TP to DPD gene expression was significantly more frequent in endometrial cancer than in normal endometrium in any menstrual phase. DPD may act cooperatively with TP to affect cell function by maintaining the pyrimidine nucleotide pool balance in normal and malignant endometrium.

Thymidine kinase in epithelial ovarian cancer: relationship with the other pyrimidine pathway enzymes.

TK is a pyrimidine metabolic pathway enzyme involved in salvage DNA synthesis. What roles TK may play in epithelial ovarian cancer and the relationships between TK and the other pyrimidine pathway enzymes remain unclear. We examined TK1 gene expression by RT-PCR and related it to gene expression of TS, TP and DPD in 69 samples from epithelial ovarian cancer, 8 low-malignant-potential tumors, 16 benign ovarian tumors and 34 normal ovaries. Additionally, cytosolic and serum TK activities were determined by radioenzymatic assay. TK1 gene expression, the ratio of TK1 to TS gene expression, that of TK1 to TP and that of TK1 to DPD were significantly higher in epithelial ovarian cancer than in normal ovaries. In epithelial ovarian cancer, TK1 gene expression correlated with cytosolic and serum TK activities, TS and TP gene expression and the ratio of TP to DPD gene expression. Patients with high-TK1 gene expression had a significantly poorer survival than those with low TK1 gene expression. Combined analysis demonstrated that the relative risk of cancer death for tumors with high TK1, high TS and high TP gene expression was greater than that for tumors with high TK1 gene expression alone. TK1 gene expression together with TS, TP and DPD gene expression may play important roles in influencing the malignant behavior of epithelial ovarian cancer. Combination therapy including TK inhibitor is a possible therapeutic intervention in patients with epithelial ovarian cancer.