Thermodynamic and structural investigation of oily wastewater treatment using peach kernel and walnut shell based activated carbon.

Despite the many articles about activated carbon with different precursors in adsorption process, no in-depth research has been carried out to understand the causes of the difference in surface adsorption characteristics of activated carbon with different precursors and different activation processes. In this work, the ability of two active carbon adsorbents made of walnut shell and peach kernel by two chemical and physical methods (totally 4 different types of activated carbon) in treatment of oily wastewater including diesel, gasoline, used oil or engine lubricant has been compared. The results show that the chemical activated peach carbon active with 97% hardness has provided the highest hardness and physical activated walnut carbon active has obtained the lowest hardness value (87%). It is also found that peach activated carbon has a higher iodine number than walnut activated carbon, and this amount can be increased using chemical methods; Therefore, the highest amount of Iodine Number is related to Peach activated carbon that is made by chemical method (1230 mg/g), and the lowest amount of iodine number is seen in walnut activated carbon that is made by physical method (1020 mg/g). moreover, the pore diameter of physical activated carbon is lower than chemical activated carbon in all cases. So that the pore diameter of chemical activated peach carbon active is equal to 22.08 µm and the measured pore diameter of physical activated peach carbon active is equal to 20.42 µm. These values for walnut are obtained as 22.74 µm and 21.86 µm, respectively. Furthermore, the temperature and pH effects on the adsorption of different synthesized oily wastewater was studied and it was found that a decrease in adsorption can be seen with an increase in temperature or decreasing the pH value, which can be referred to this fact that the process of adsorption is an exothermic process. Finally, to analyze the compatibility of adsorption isotherms with experimental data and to predict the adsorption process, three different isotherms named Langmuir, Temkin, and Freundlich isotherms were applied and their parameters were correlated. The correlation results show that the Langmuir isotherm had the best correlation in all cases compared to the Freundlich and Temkin isotherms, based on the correlation coefficient, and the calculated R2 values which was greater than 0.99 in all the studied cases.

Daily scale air quality index forecasting using bidirectional recurrent neural networks: Case study of Delhi, India.

This research was established to accurately forecast daily scale air quality index (AQI) which is an essential environmental index for decision-making. Researchers have projected different types of models and methodologies for AQI forecasting, such as statistical techniques, machine learning (ML), and most recently deep learning (DL) models. The modelling development was adopted for Delhi city, India which is a major city with air pollution issues simialir to entire urban cities of India especially during winter seasons. This research was predicted AQI using different versions of DL models including Long-Short Term Memory (LSTM), Bidirectional LSTM (Bi-LSTM) and Bidirectional Recurrent Neural Networks (Bi-RNN) in addition to Kernel Ridge Regression (KRR). Results indicated that Bi-RNN model consistently outperformed the other models in both training and testing phases, while the KRR model consistently displayed the weakest performance. The outstanding performance of the models development displayed the requirement of adequate data to train the models. The outcomes of the models showed that LSTM, BI-LSTM, KRR had lower performance compared with Bi-RNN models. Statistically, Bi-RNN model attained maximum cofficient of determination (R2 = 0.954) and minimum root mean square error (RMSE = 25.755). The proposed model in this research revealed the robust predictable to provide a valuable base for decision-making in the expansion of combined air pollution anticipation and control policies targeted at addressing composite air pollution problems in the Delhi city.

Heatwaves in Peninsular Malaysia: a spatiotemporal analysis.

One of the direct and unavoidable consequences of global warming-induced rising temperatures is the more recurrent and severe heatwaves. In recent years, even countries like Malaysia seldom had some mild to severe heatwaves. As the Earth's average temperature continues to rise, heatwaves in Malaysia will undoubtedly worsen in the future. It is crucial to characterize and monitor heat events across time to effectively prepare for and implement preventative actions to lessen heatwave's social and economic effects. This study proposes heatwave-related indices that take into account both daily maximum (Tmax) and daily lowest (Tmin) temperatures to evaluate shifts in heatwave features in Peninsular Malaysia (PM). Daily ERA5 temperature dataset with a geographical resolution of 0.25° for the period 1950-2022 was used to analyze the changes in the frequency and severity of heat waves across PM, while the LandScan gridded population data from 2000 to 2020 was used to calculate the affected population to the heatwaves. This study also utilized Sen's slope for trend analysis of heatwave characteristics, which separates multi-decadal oscillatory fluctuations from secular trends. The findings demonstrated that the geographical pattern of heatwaves in PM could be reconstructed if daily Tmax is more than the 95th percentile for 3 or more days. The data indicated that the southwest was more prone to severe heatwaves. The PM experienced more heatwaves after 2000 than before. Overall, the heatwave-affected area in PM has increased by 8.98 km2/decade and its duration by 1.54 days/decade. The highest population affected was located in the central south region of PM. These findings provide valuable insights into the heatwaves pattern and impact.

Isotherms, kinetics and thermodynamic mechanism of methylene blue dye adsorption on synthesized activated carbon.

The treatment of methylene blue (MB) dye wastewater through the adsorption process has been a subject of extensive research. However, a comprehensive understanding of the thermodynamic aspects of dye solution adsorption is lacking. Previous studies have primarily focused on enhancing the adsorption capacity of methylene blue dye. This study aimed to develop an environmentally friendly and cost-effective method for treating methylene blue dye wastewater and to gain insights into the thermodynamics and kinetics of the adsorption process for optimization. An adsorbent with selective methylene blue dye adsorption capabilities was synthesized using rice straw as the precursor. Experimental studies were conducted to investigate the adsorption isotherms and models under various process conditions, aiming to bridge gaps in previous research and enhance the understanding of adsorption mechanisms. Several adsorption isotherm models, including Langmuir, Temkin, Freundlich, and Langmuir-Freundlich, were applied to theoretically describe the adsorption mechanism. Equilibrium thermodynamic results demonstrated that the calculated equilibrium adsorption capacity (qe) aligned well with the experimentally obtained data. These findings of the study provide valuable insights into the thermodynamics and kinetics of methylene blue dye adsorption, with potential applications beyond this specific dye type. The utilization of rice straw as an adsorbent material presents a novel and cost-effective approach for MB dye removal from wastewater.

Optimization of oil industry wastewater treatment system and proposing empirical correlations for chemical oxygen demand removal using electrocoagulation and predicting the system's performance by artificial neural network.

The alarming pace of environmental degradation necessitates the treatment of wastewater from the oil industry in order to ensure the long-term sustainability of human civilization. Electrocoagulation has emerged as a promising method for optimizing the removal of chemical oxygen demand (COD) from wastewater obtained from oil refineries. Therefore, in this study, electrocoagulation was experimentally investigated, and a single-factorial approach was employed to identify the optimal conditions, taking into account various parameters such as current density, pH, COD concentration, electrode surface area, and NaCl concentration. The experimental findings revealed that the most favorable conditions for COD removal were determined to be 24 mA/cm2 for current density, pH 8, a COD concentration of 500 mg/l, an electrode surface area of 25.26 cm2, and a NaCl concentration of 0.5 g/l. Correlation equations were proposed to describe the relationship between COD removal and the aforementioned parameters, and double-factorial models were examined to analyze the impact of COD removal over time. The most favorable outcomes were observed after a reaction time of 20 min. Furthermore, an artificial neural network model was developed based on the experimental data to predict COD removal from wastewater generated by the oil industry. The model exhibited a mean absolute error (MAE) of 1.12% and a coefficient of determination (R2) of 0.99, indicating its high accuracy. These findings suggest that machine learning-based models have the potential to effectively predict COD removal and may even serve as viable alternatives to traditional experimental and numerical techniques.

Using Machine Learning Models to Predict Hydroponically Grown Lettuce Yield.

Prediction of crop yield is an essential task for maximizing the global food supply, particularly in developing countries. This study investigated lettuce yield (fresh weight) prediction using four machine learning (ML) models, namely, support vector regressor (SVR), extreme gradient boosting (XGB), random forest (RF), and deep neural network (DNN). It was cultivated in three hydroponics systems (i.e., suspended nutrient film technique system, pyramidal aeroponic system, and tower aeroponic system), which interacted with three different magnetic unit strengths under a controlled greenhouse environment during the growing season in 2018 and 2019. Three scenarios consisting of the combinations of input variables (i.e., leaf number, water consumption, dry weight, stem length, and stem diameter) were assessed. The XGB model with scenario 3 (all input variables) yielded the lowest root mean square error (RMSE) of 8.88 g followed by SVR with the same scenario that achieved 9.55 g, and the highest result was by RF with scenario 1 (i.e., leaf number and water consumption) that achieved 12.89 g. All model scenarios having Scatter Index (SI) (i.e., RMSE divided by the average values of the observed yield) values less than 0.1 were classified as excellent in predicting fresh lettuce yield. Based on all of the performance statistics, the two best models were SVR with scenario 3 and DNN with scenario 2 (i.e., leaf number, water consumption, and dry weight). However, DNN with scenario 2 requiring less input variables is preferred. The potential of the DNN model to predict fresh lettuce yield is promising, and it can be applied on a large scale as a rapid tool for decision-makers to manage crop yield.

Selection of the gridded temperature dataset for assessment of thermal bioclimatic environmental changes in Amu Darya River basin.

Assessment of the thermal bioclimatic environmental changes is important to understand ongoing climate change implications on agriculture, ecology, and human health. This is particularly important for the climatologically diverse transboundary Amy Darya River basin, a major source of water and livelihood for millions in Central Asia. However, the absence of longer period observed temperature data is a major obstacle for such analysis. This study employed a novel approach by integrating compromise programming and multicriteria group decision-making methods to evaluate the efficiency of four global gridded temperature datasets based on observation data at 44 stations. The performance of the proposed method was evaluated by comparing the results obtained using symmetrical uncertainty, a machine learning similarity assessment method. The most reliable gridded data was used to assess the spatial distribution of global warming-induced unidirectional trends in thermal bioclimatic indicators (TBI) using a modified Mann-Kendall test. Ranking of the products revealed Climate Prediction Center (CPC) temperature as most efficient in reconstruction observed temperature, followed by TerraClimate and Climate Research Unit. The ranking of the product was consistent with that obtained using SU. Assessment of TBI trends using CPC data revealed an increase in the Tmin in the coldest month over the whole basin at a rate of 0.03-0.08 °C per decade, except in the east. Besides, an increase in diurnal temperature range and isothermally increased in the east up to 0.2 °C and 0.6% per decade, respectively. The results revealed negative implications of thermal bioclimatic change on water, ecology, and public health in the eastern mountainous region and positive impacts on vegetation in the west and northwest. Supplementary Information: The online version contains supplementary material available at 10.1007/s00477-022-02172-8.

Assessment of Soft Computing Techniques for the Prediction of Compressive Strength of Bacterial Concrete.

In this investigation, the potential of M5P, Random Tree (RT), Reduced Error Pruning Tree (REP Tree), Random Forest (RF), and Support Vector Regression (SVR) techniques have been evaluated and compared with the multiple linear regression-based model (MLR) to be used for prediction of the compressive strength of bacterial concrete. For this purpose, 128 experimental observations have been collected. The total data set has been divided into two segments such as training (87 observations) and testing (41 observations). The process of data set separation was arbitrary. Cement, Aggregate, Sand, Water to Cement Ratio, Curing time, Percentage of Bacteria, and type of sand were the input variables, whereas the compressive strength of bacterial concrete has been considered as the final target. Seven performance evaluation indices such as Correlation Coefficient (CC), Coefficient of determination (R2), Mean Absolute Error (MAE), Root Mean Square Error (RMSE), Bias, Nash-Sutcliffe Efficiency (NSE), and Scatter Index (SI) have been used to evaluate the performance of the developed models. Outcomes of performance evaluation indices recommend that the Polynomial kernel function based SVR model works better than other developed models with CC values as 0.9919, 0.9901, R2 values as 0.9839, 0.9803, NSE values as 0.9832, 0.9800, and lower values of RMSE are 1.5680, 1.9384, MAE is 0.7854, 1.5155, Bias are 0.2353, 0.1350 and SI are 0.0347, 0.0414 for training and testing stages, respectively. The sensitivity investigation shows that the curing time (T) is the vital input variable affecting the prediction of the compressive strength of bacterial concrete, using this data set.

A hybrid novel SVM model for predicting CO2 emissions using Multiobjective Seagull Optimization.

The agricultural sector is one of the most important sources of CO2 emissions. Thus, the current study predicted CO2 emissions based on data from the agricultural sectors of 25 provinces in Iran. The gross domestic product (GDP), the square of the GDP (GDP2), energy use, and income inequality (Gini index) were used as the inputs. The study used support vector machine (SVM) models to predict CO2 emissions. Multiobjective algorithms (MOAs), such as the seagull optimization algorithm (MOSOA), salp swarm algorithm (MOSSA), bat algorithm (MOBA), and particle swarm optimization (MOPSO) algorithm, were used to perform three important tasks for improving the SVM models. Additionally, an inclusive multiple model (IMM) used the outputs of the MOSOA, MOSSA, MOBA, and MOPSO algorithms as the inputs for predicting CO2 emissions. It was observed that the best kernel function based on the SVM-MOSOA was the radial function. Additionally, the best input combination used all the gross domestic product (GDP), squared GDP (GDP2), energy use, and income inequality (Gini index) inputs. The results indicated that the quality of the obtained Pareto front based on the MOSOA was better than those of the other algorithms. Regarding the obtained results, the IMM model decreased the mean absolute errors of the SVM-MOSOA, SVM-MOSSA, SVM-MOBA, and SVM-PSO models by 24, 31, 69, and 76%, respectively, during the training stage. The current study showed that the IMM model was the best model for predicting CO2 emissions.

A new hybrid model based on relevance vector machine with flower pollination algorithm for phycocyanin pigment concentration estimation.

Precise monitoring of cyanobacteria concentration in water resources is a daunting task. The development of reliable tools to monitor this contamination is an important research topic in water resources management. Indirect methods such as chlorophyll-a determination, cell counting, and toxin measurement of the cyanobacteria are tedious, cumbersome, and often lead to inaccurate results. The quantity of phycocyanin (PC) pigment is considered more appropriate for cyanobacteria monitoring. Traditional approaches for PC estimation are time-consuming, expensive, and require high expertise. Recently, some studies have proposed the application of artificial intelligence (AI) techniques to predict the amount of PC concentration. Nonetheless, most of these researches are limited to standalone modeling schemas such as artificial neural network (ANN), multilayer perceptron (MLP), and support vector machine (SVM). The independent schema provides imprecise results when faced with highly nonlinear systems and data uncertainties resulting from environmental disturbances. To alleviate the limitations of the existing models, this study proposes the first application of a hybrid AI model that integrates the potentials of relevance vector machine (RVM) and flower pollination algorithm (RVM-FPA) to predict the PC concentration in water resources. The performance of the hybrid model is compared with the standalone RVM model. The prediction performance of the proposed models was evaluated at two stations (stations 508 and 478) using different statistical and graphical performance evaluation methods. The results showed that the hybrid models exhibited higher performance at both stations compared to the standalone RVM model. The proposed hybrid RVM-FPA can therefore serve as a reliable predictive tool for PC concentration in water resources.

Application of soft computing to predict water quality in wetland.

Prediction of water quality is a critical issue because of its significant impact on human and ecosystem health. This research aims to predict water quality index (WQI) for the free surface wetland using three soft computing techniques namely, adaptive neuro-fuzzy system (ANFIS), artificial neural networks (ANNs), and group method of data handling (GMDH). Seventeen wetland points for a period of 14 months were considered for monitoring water quality parameters including conductivity, suspended solid (SS), biochemical oxygen demand (BOD), ammoniacal nitrogen (AN), chemical oxygen demand (COD), dissolved oxygen (DO), temperature, pH, phosphate nitrite, and nitrate. The sensitivity analysis performed by ANFIS indicates that the significant parameters to predict WQI are pH, COD, AN, and SS. The results indicated that ANFIS with Nash-Sutcliffe Efficiency (NSE = 0.9634) and mean absolute error (MAE = 0.0219) has better performance to predict the WQI comparing with ANNs (NSE = 0.9617 and MAE = 0.0222) and GMDH (NSE = 0.9594 and MAE = 0.0245) models. However, ANNs provided a comparable prediction and the GMDH can be considered as a technique with an acceptable prediction for practical purposes. The findings of this study could be used as an effective reference for policy makers in the field of water resource management. Decreasing variables, reduction of running time, and high speed of these approaches are the most important reasons to employ them in any aquatic environment worldwide.