ORMOCHALCs: organically modified chalcogenide polymers for infrared optics.

A novel method combining elemental sulfur and selenium was developed, yielding crystalline sulfur-selenium compounds. The compounds were melted, and an organic comonomer added. Once the organic comonomer was consumed, the viscous compound was vitrified and allowed to cool yielding organic-inorganic hybrid polymers that are termed Organically Modified Chalcogenide (ORMOCHALC) polymers.

Optimized moth-eye anti-reflective structures for As2S3 chalcogenide optical fibers.

We computationally investigate moth-eye anti-reflective nanostructures imprinted on the endfaces of As2S3 chalcogenide optical fibers. With a goal of maximizing the transmission through the endfaces, we investigate the effect of changing the parameters of the structure, including the height, width, period, shape, and angle-of-incidence. Using these results, we design two different moth-eye structures that can theoretically achieve almost 99.9% average transmisison through an As2S3 surface.

Angle-of-incidence performance of random anti-reflection structures on curved surfaces.

Random anti-reflection structured surfaces (rARSS) have been reported to improve transmittance of optical-grade fused silica planar substrates to values greater than 99%. These textures are fabricated directly on the substrates using reactive-ion etching techniques, and often result in transmitted spectra with no measurable interference effects (fringes) for a wide range of wavelengths. The inductively coupled reactive-ion plasma (ICP-RIE) used in the fabrication process to etch the rARSS is anisotropic and thus well suited for planar components. The improvement in spectral transmission has been found to be independent of optical incidence angles for values from 0° to ±30°. Qualifying and quantifying the rARSS performance on curved substrates, such as convex lenses, is required to optimize the fabrication of the desired AR effect on optical-power elements. In this work, rARSS was fabricated on fused silica plano-convex lenses using a planar-substrate optimized ICP-RIE process to maximize optical transmission in the range from 500 to 1100 nm. Results are presented from optical transmission tests of rARSS lenses for both TE and TM incident polarizations at a wavelength of 633 nm and over a 70° full field of view. These results suggest optimization of the fabrication process to account for anisotropy is not required, mainly due to the wide angle-of-incidence AR tolerance performance of the rARSS lenses.

Desorption electrospray ionization-mass spectrometric analysis of low vapor pressure chemical particulates collected from a surface.

The collection of a low vapor pressure chemical simulant triethyl phosphate sorbed onto silica gel (TEP/SG) from a surface with subsequent analysis of the TEP/SG particulates using desorption electrospray ionization-mass spectrometry (DESI-MS) is described. Collection of TEP/SG particulates on a surface was accomplished using a sticky screen sampler composed of a stainless steel screen coated with partially polymerized polydimethylsiloxane (PDMS). DESI-MS analysis of TEP/SG particulates containing different percentages of TEP sorbed onto silica gel enabled the generation of response curves for the TEP ions m/z 155 and m/z 127. Using the response curves the calculation of the mass of TEP in a 25 wt% sample of TEP/SG was calculated, results show that the calculated mass of TEP was 14% different from the actual mass of TEP in the sample using the m/z 127 TEP ion response curve. Detection limits for the TEP vapor and TEP/SG particulates were calculated to be 4 µg and 6 particles, respectively.

Calculation of the expected output spectrum for a mid-infrared supercontinuum source based on As 2 S3 chalcogenide photonic crystal fibers.

We computationally investigate supercontinuum generation in an As 2 S3 solid core photonic crystal fiber (PCF) with a hexagonal cladding of air holes. With a goal of obtaining a supercontinuum output spectrum that can predict what might be seen in an experiment, we investigate the spectral and statistical behavior of a mid-infrared supercontinuum source using a large ensemble average of 106 realizations, in which the input pulse duration and energy vary. The output spectrum is sensitive to small changes (0.1%) in these pulse parameters. We show that the spectrum can be divided into three regions with distinct characteristics: a short-wavelength region with high correlation, a middle-wavelength region with minimal correlation, and a long-wavelength region where the behavior is dominated by a few rare large-bandwidth events. We show that statistically significant fluctuations exist in the experimentally expected output spectrum and that we can reproduce an excellent match to that spectrum with a converged shape and bandwidth using 5000 realizations.

Efficient inscription of Bragg gratings in As2S3 fibers using near bandgap light.

Efficient inscription of Fiber Bragg gratings (FBGs) in single-mode, thin cladding As(2)S(3) fibers is demonstrated by using near bandgap light at 532 nm. The FBGs with the reflectivity of over 80% can be induced in only 80-90 s, substantially faster than in previous reports. The dynamics of the grating growth are investigated in the photosensitivity process, showing a fast blue shift of the Bragg wavelength and then a somewhat slower red shift. The aging of the grating after fabrication is also reported, indicating a 37% decay of the grating strength.

Sampler for collection and analysis of low vapor pressure chemical (LVPC) particulates/aerosols.

Detection of low vapor pressure chemicals (LVPCs) such as pesticides and other toxic/hazardous materials on various environmental surfaces as well as LVPC aerosols is a significant challenge for current vapor phase detectors. We describe a novel sampling device which utilizes stainless steel screens coated with a sticky polydimethylsiloxane coating for collecting LVPCs aerosolized off of a surface. Results are presented for the collection and detection of a pesticide simulant, dimethyl methylphosphonate sorbed onto silica gel (DMMP/SG), using direct analysis in real time-cylindrical ion trap mass spectrometry (DART-CITMS).

Collection method for chemical particulates on surfaces with detection using thermal desorption-ion trap mass spectrometry.

Successful analysis of particulate/low vapor pressure analytes such as explosives and toxic chemicals, and commercial pesticides require new sampling tools that enable detection of these analytes using current vapor phase detection instruments. We describe a sampling approach that uses stainless steel screens coated with a sticky polydimethyl siloxane (PDMS) coating to capture particulates from surfaces. Preliminary results for the collection of dimethyl methylphosphonate (DMMP) sorbed onto silica gel (SG) particulates (DMMP/SG) from a surface with subsequent analysis by thermal desorption-cylindrical ion trap mass spectrometry (TD-CITMS) are reported.

Low-temperature deposition of BaCuSF, a visible through mid-infrared p-type transparent conductor.

Barium copper sulfur fluoride (BaCuSF) is a p-type transparent conductor (p-TC) that, when doped with potassium, exhibits exceptionally high conductivity. The results of a detailed optical and electronic characterization of BaCuSF thin films deposited at a substrate temperature of 100 °C are presented. X-ray diffractometry shows the presence of a cubic BaCuSF phase. Spectroscopic measurements demonstrate that the films transmit from the visible through the mid-infrared with a band gap of 1.8 eV. Hall measurements indicate that the material is a degenerate semiconductor. As deposited, the films exhibit conductivity at room temperature of approximately 260 S/cm - among the highest reported room temperature conductivities for p-TCs. After post-deposition treatment in water, their conductivity increases to as high as 800 S/cm, and their band gap is reduced to 1.5 eV. The potential for low temperature deposition of p-type films with high conductivity and optical transmittance makes BaCuSF promising for several applications including flexible electronics and photovoltaics.

Octave spanning supercontinuum in an As2S3 taper using ultralow pump pulse energy.

An octave spanning spectrum is generated in an As2S3 taper via 77 pJ pulses from an ultrafast fiber laser. Using a previously developed tapering method, we construct a 1.3 µm taper that has a zero-dispersion wavelength around 1.4 µm. The low two-photon absorption of sulfide-based chalcogenide fiber allows for higher input powers than previous efforts in selenium-based chalcogenide tapered fibers. This higher power handling capability combined with input pulse chirp compensation allows an octave spanning spectrum to be generated directly from the taper using the unamplified laser output.

Characterization of picosecond pulse nonlinear propagation in chalcogenide As(2)S(3) fiber.

We characterize the nonlinear propagation of picosecond pulses in chalcogenide As(2)S(3) single-mode fiber using a pump-probe technique. The cross-phase modulation (XPM)-induced sideband broadening and stimulated Raman scattering (SRS)-induced sideband amplification are measured in order to map out the Raman gain spectrum of this glass across the C-band. We extract the Raman response function from the Raman gain spectrum and determine the power and polarization dependence of the SRS. In contrast to previous work using As(2)Se(3) fiber, we find that the As(2)S(3) fiber does not suffer from large two-photon absorption (TPA) in the wavelength range of the telecommunications band. We achieved a 20 dB peak Raman gain at a Stokes shift of 350 cm(-1) in a 205 mm length of As(2)S(3) single-mode fiber. The Raman gain coefficient is estimated to be 4.3x10(-12) m/W and the threshold pump peak power is estimated to be 16.2 W for the 205 mm As(2)S(3) fiber. We also demonstrate that we can infer the dispersion of the As(2)S(3) fiber and justify the Raman response function by comparing simulation and experimental results.

High bit rate all-optical signal processing in a fiber photonic wire.

We report the first demonstration of high bit rate signal processing by a fiber-based photonic wire. We achieve 160 Gb/s demultiplexing via four wave mixing in a 1.9 microm diameter photonic wire tapered from As(2)S(3) chalcogenide glass single mode fibre, with very low pump power requirements ( < 20 mW average power, 0.45 W peak power), enabled by a very high nonlinearity (gamma approximately 7850 W(-1) km (-1) ) and greatly reduced dispersion.

Low-frequency electromagnetic field effects on functional groups in human skin keratinocytes cells revealed by IR-SNOM.

Human HaCaT cells, exposed for 24 h to a 1 mT (rms) 50 Hz sinusoidal magnetic field in a temperature-regulated solenoid, suffer detectable changes in their biochemical properties and shapes. By using infrared wavelength-selective scanning near-field optical microscopy, we observed changes in the distribution of the inner chemical functional groups and in the cell morphology with a resolution of 80-100 nm.

Infrared scanning near-field optical microscopy investigates order and clusters in model membranes.

Due to its surface sensitivity and high spatial resolution, scanning near-field optical microscopy (SNOM) has a significant potential to study the lateral organization of membrane domains and clusters. Compared to other techniques, infrared near-field microscopy in the spectroscopic mode has the advantage to be sensitive to specific chemical bonds. In fact, spectroscopic SNOM in the infrared spectral range (IR-SNOM) reveals the chemical content of the sample with a lateral resolution around 100 nm (Cricenti et al., 1998a, 1998b, 2003). Model lipid membranes were studied by IR-SNOM at several wavelengths. Topographical micrographs reveal the presence of islands at the surface and the optical images indicate the formation of locally ordered multiple bilayers - both critically important features for biotechnology and medical applications.

Characterization of mid-infrared single mode fibers as modal filters.

We present a technique for measuring the modal filtering ability of single mode fibers. The ideal modal filter rejects all input field components that have no overlap with the fundamental mode of the filter and does not attenuate the fundamental mode. We define the quality of a nonideal modal filter Q(f) as the ratio of transmittance for the fundamental mode to the transmittance for an input field that has no overlap with the fundamental mode. We demonstrate the technique on a 20 cm long mid-infrared fiber that was produced by the U.S. Naval Research Laboratory. The filter quality Q(f) for this fiber at 10.5 microm wavelength is 1000+/-300. The absorption and scattering losses in the fundamental mode are approximately 8 dB/m. The total transmittance for the fundamental mode, including Fresnel reflections, is 0.428+/-0.002. The application of interest is the search for extrasolar Earthlike planets using nulling interferometry. It requires high rejection ratios to suppress the light of a bright star, so that the faint planet becomes visible. The use of modal filters increases the rejection ratio (or, equivalently, relaxes requirements on the wavefront quality) by reducing the sensitivity to small wavefront errors. We show theoretically that, exclusive of coupling losses, the use of a modal filter leads to the improvement of the rejection ratio in a two-beam interferometer by a factor of Q(f).

Waveguide amplifiers in sputtered films of Er3+-doped gallium lanthanum sulfide glass.

Waveguide amplifiers fabricated in Er3+-doped gallium lanthanum sulfide (GLS) glass are demonstrated. GLS is deposited onto fused silica substrates by RF magnetron sputtering, and waveguides are patterned by use of the lift-off technique. The waveguides exhibit a total internal gain of 6.7 dB (2.8 dB/cm) for a signal with a wavelength of 1.55 mum. This experiment is, to the best of our knowledge, the first demonstration of gain in an Er3+-doped chalcogenide glass waveguide. The fabrication methods we apply, if used with other rare earth dopants, could potentially be employed to produce sources operating in the mid-IR.

Small-core As-Se fiber for Raman amplification.

We have demonstrated Raman small-core As-Se fiber. More than 20-dB of gain was observed in a 1.1-m length of fiber pumped by a nanosecond pulse of approximately 10.8-W peak power at 1.50 microm. The peak of the Raman gain occurred at a shift of approximately 240 cm(-1). The Raman gain coefficient is estimated to be approximately 2.3 x 10(-11) m/W, which is more than 300 times greater than that of silica. The large Raman gain coefficient coupled with the large IR transparency window of these fibers shows promise for development of As-Se Raman fiber lasers and amplifiers in the near-, mid-, and long-IR spectral regions.

Modeling of a mid-IR chalcogenide fiber Raman laser.

A computer model using a finite element technique was written to model the behavior of a chalcogenide fiber Raman laser. The model demonstrates the feasibility of a middle infrared fiber Raman laser pumped at 5.59-microm by a carbon monoxide laser and operating at a wavelength of 6.46-microm. This wavelength may be of interest in surgical applications since it corresponds to the amide II absorption. Calculations show slope efficiencies can approach 80% with moderate threshold powers.

Integrin-linked kinase, a promising cancer therapeutic target: biochemical and biological properties.

Integrin-linked kinase (ILK) is an ankyrin repeat-containing Ser/Thr kinase that interacts with the cytoplasmic domains of beta(1) and beta(3) integrins. ILK is widely expressed in tissues throughout the body, and, as might be expected, appears to mediate a diversity of functions relating to its role in coupling integrins and growth factor receptors to downstream signaling pathways. Through its downstream targets protein kinase B/Akt and glycogen synthase kinase-3beta, ILK appears to be involved in several oncogenesis-related events, including suppression of apoptosis and promotion of cell survival, as well as cell migration and invasion. Over-expression of ILK in epithelial cells results in anchorage-independent cell growth with increased cell cycle progression. Inoculation of nude mice with ILK over-expressing cells leads to tumor formation. Furthermore, increased ILK expression and activity have been correlated with malignancy in several human tumor types, including breast, prostate, brain, and colon carcinomas. Based on these findings, ILK represents an excellent therapeutic target for the prevention of tumor progression. Here, we provide an overview of the physical and biochemical properties of ILK, and present data describing the impact of small-molecule ILK inhibitors on several ILK-mediated cellular functions.

Treatments for secondary postpartum haemorrhage.

BACKGROUND: Secondary postpartum haemorrhage is any abnormal or excessive bleeding from the birth canal occurring between 24 hours and 12 weeks postnatally. In developed countries, two per cent of postnatal women are admitted to hospital with this condition, half of them undergoing uterine surgical evacuation; in developing countries it is a major contributor to maternal death. OBJECTIVES: To evaluate the relative effectiveness and safety of the treatments used for secondary postpartum haemorrhage. SEARCH STRATEGY: We searched the Cochrane Pregnancy and Childbirth Group trials register (May 2001), the Cochrane Controlled Trials Register (The Cochrane Library, issue 2, 2001), MEDLINE (back to 1966) and EMBASE (back to 1988). The National Research Register was also searched. The reference lists of trial reports and reviews were searched by hand. Where possible, further sources were sought from the first named authors of the papers identified. SELECTION CRITERIA: All randomised or quasi randomised comparisons between drug therapies, surgical therapies and placebo or no treatment for the management of secondary postpartum haemorrhage occurring between 24 hours and three months following a pregnancy of at least 24 weeks gestation. DATA COLLECTION AND ANALYSIS: Reports of possibly eligible studies were scrutinised by two investigators. The third investigator acted as an advisor/arbitrator. MAIN RESULTS: Of the 45 papers identified, none met the inclusion criteria. REVIEWER'S CONCLUSIONS: No information is available from randomised controlled trials to inform the management of women with secondary postpartum haemorrhage. This topic may have received little attention because it is perceived as being associated with maternal morbidity rather than mortality in developed countries; it is only recently that the extent and importance of postnatal maternal morbidity has been recognised. A well designed randomised controlled trial comparing the various drug therapies for women with secondary postpartum haemorrhage against each other and against placebo or no treatment groups is needed.