RESUMEN
In the present work, the tribological experiments on sliding the electron beam composite M2+WC coating have been carried out with characterization of the sample microstructures and phases both before and after the testing using metallography, SEM, EDS, and XRD. The sliding in the speed range 0.8-3.6 m/s resulted in simultaneous reduction in both wear rate and coefficient of friction with the sliding speed. Investigations showed that such a tribological adaptation was due to the tribochemical generation of lubricative FeWO4 and Fe2WO6 mixed oxides and the generation of a mechanically mixed composite layer on the worn surfaces that consisted of carbide fragments, an oxidized metal matrix, and was lubricated by in-situ formed mixed iron-tungsten oxides.
RESUMEN
In the presented work, the effect of friction stir processing admixing the zirconium tungstate ZrW2O8 powder on the microstructure, mechanical and tribological properties of the AA5056 Al-Mg alloy stir zone has been studied. The FSP resulted in obtaining dense composite stir zones where α-ZrW2O8 underwent the following changes: (i) high-temperature transformation into metastable ß'-ZrW2O8 and (ii) decomposition into WO3 and ZrO2 oxides followed by the formation of intermetallic compounds WAl12 and ZrAl3. These precipitates served as reinforcing phases to improve mechanical and tribological characteristics of the obtained fine-grained composites. The reduced values of wear rate and friction coefficient are due to the combined action the Hall-Petch mechanism and reinforcement by the decomposition products, including Al2O3, ZrO2, ß'-ZrW2O8 and intermetallic compounds such as WAl12 and ZrAl3. Potential applications of the above-discussed composites maybe related to their improved tribological characteristics, for example in aerospace and vehicle-building industries.
RESUMEN
Multi-pass friction stir processing (FSP) was used to obtain a titanium alloy/copper hybrid composite layer by intermixing copper powder with a Ti6Al4V alloy. A macrostructurally inhomogeneous stir zone was obtained with both its top and middle parts composed of fine dynamically recrystallized α- and ß-Ti grains, as well as coarse intermetallic compounds (IMCs) of Ti2Cu and TiCu2, respectively. Some ß grains experienced ß â α decomposition with the formation of acicular α-Ti microstructures either inside the former ß-Ti grains or at their grain boundaries. Both types of ß â α decomposition were especially clearly manifested in the vicinity of the Ti2Cu grains, i.e., in the copper-lean regions. The middle part of the stir zone additionally contained large dislocation-free ß-Ti grains that resulted from static recrystallization. Spinodal decomposition, as well as solid-state amorphization of copper-rich ß-Ti grains, were discovered. The FSPed stir zone possessed hardness that was enhanced by 25% as compared to that of the base metal, as well as higher strength, ductility, and wear resistance than those obtained using four-pass FSPed Ti6Al4V.
RESUMEN
Dissimilar friction stir processing on CuZn37/AA5056 was performed to study structural and phase evolution of a friction stir zone. Formation of 5-10 µm intermetallic compounds (IMCs) such as Al2Cu was the main type of diffusion reaction between copper and aluminum. Other alloying elements such as Mg and Zn were forced out of the forming Al2Cu grains and dissolved in the melt formed due to exothermic effect of the Al2Cu formation. When solidified, these Zn-enriched zones were represented by α-Al+Al2Cu+Zn phases or α-Al+Al2Cu+Zn+MgZn regions. Eutectic Zn+MgZn was undoubtedly formed the melt after stirring had stopped. These zones were proven to be weak ones with respect to pull-off test since MgZn was detected on the fracture surface. Tensile strength of the stirred zone metal was achieved at the level of that of AA5056.
RESUMEN
Evaporation of paraffin and ultra-high-molecular-weight polyethylene admixed with alumina powder for the slip casting and sintering process allowed the obtainment of segmented porous alumina ceramics with 50% total porosity, whose deformation behavior we studied. Structurally, these ceramic materials were composed of large and small pores, and a system of discontinuities subdividing the samples into segments. Using digital image correlation (DIC), strain distribution maps were obtained that allowed the observation of strain localization zones, where primary cracks propagated along the interblock discontinuities. Two stages were revealed to be responsible for different mechanisms that provided the sample with damage tolerance under compression loading: the first stage was crack propagation along the block boundaries, which was followed by the second stage of microcracking and fragmentation, consisting of filling of the free spaces with fragments, compaction band generation, and stabilization of the crack. Both stages comprise a cycle that is repeated again and again until the full volume of the sample is occupied by the compaction bands.
