RESUMEN
In this study, substochiometric hole-selective molybdenum oxide (MoOx) contacts in crystalline silicon (c-Si) solar cells were investigated by a combination of transmission electron microscopy (TEM) and spatially resolved electron energy-loss spectroscopy (SR-EELS). It was observed that a ≈ 4 nm SiOx interlayer grows at the MoOx/c-Si interface during the evaporation of MoOx over a c-Si substrate. SR-EELS analyses revealed the presence of a 1.5 nm diffused MoOx/indium tin oxide (ITO) interface in both as-deposited and annealed samples. Moreover, the presence of a 1 nm thin layer with a lower oxidation state of Mo was detected at the SiOx/MoOx interface in an as-deposited state, which disappears upon annealing. Overall, it was evident that no hole-blocking interlayer is formed at the MoOx/ITO interface during annealing and homogenization of the MoOx layer takes place during the annealing process. Furthermore, device simulations revealed that efficient hole collection is dependent on MoOx work function and that reduction in the work function of MoOx results in loss of band bending and negatively impacts hole selectivity.
RESUMEN
We report on tin gallium oxide ((SnxGa1-x)2O3) solar-blind metal-semiconductor-metal (MSM) photodetectors grown by plasma-assisted molecular beam epitaxy on c-plane sapphire substrates with varying tin content up to XSn=10%. Incorporation of Sn into Ga2O3 was found to shift the optical bandgap of the epilayers from 5.0 eV (248 nm) for 0% Sn to 4.6 eV (270 nm) for 10% Sn content. Varying of the Sn concentration was also found to enable controlled tuning of the peak responsivity and cutoff wavelengths of MSM devices fabricated from the epilayers, with peak responsivity ranging from 0.75 A/W to nearly 16 A/W as the Sn concentration was increased from 0% to 10%. The high responsivity is attributed to photoconductive gain that increases for higher Sn concentrations and is accompanied by a slowing of the temporal response of the MSM detectors.
RESUMEN
In this study, the cross-section of electron-selective titanium oxide (TiO2) contacts for n-type crystalline silicon solar cells were investigated by transmission electron microscopy. It was revealed that the excellent cell efficiency of 21.6% obtained on n-type cells, featuring SiO2/TiO2/Al rear contacts and after forming gas annealing (FGA) at 350°C, is due to strong surface passivation of SiO2/TiO2 stack as well as low contact resistivity at the Si/SiO2/TiO2 heterojunction. This can be attributed to the transformation of amorphous TiO2 to a conducting TiO2-x phase. Conversely, the low efficiency (9.8%) obtained on cells featuring an a-Si:H/TiO2/Al rear contact is due to severe degradation of passivation of the a-Si:H upon FGA.
RESUMEN
Thin TiO2 films are demonstrated to be an excellent electron-selective contact for crystalline silicon solar cells. An efficiency of 21.6% is achieved for crystalline silicon solar cells featuring a full-area TiO2 -based electron-selective contact.
RESUMEN
We present a practical method to determine femtosecond laser induced refractive index changes in transparent materials. Based on an iterative Fourier transform algorithm, this technique spatially resolves the refractive index of complex structures by combining the dimensions of the modified region with the corresponding phase change extracted from far-field intensity measurements. This approach is used to characterize optical waveguides written by a femtosecond laser in borosilicate glass.
RESUMEN
We report on magneto-photoluminescence studies of InAs/GaAs quantum dots (QDs) of considerably different densities, from dense ensembles down to individual dots. It is found that a magnetic field applied in Faraday geometry decreases the photoluminescence (PL) intensity of QD ensembles, which is not accompanied by the corresponding increase of PL signal of the wetting layer on which QDs are grown. The model suggested to explain these data assumes considerably different strengths of suppression of electron and hole fluxes by a magnetic field. This idea has been successfully checked in experiments on individual QDs, where the PL spectra allow to directly monitor the charge state of a QD and, hence, to conclude about relative magnitudes of electron and hole fluxes toward the QD. Comparative studies of different individual QDs have revealed that the internal electric field in the sample (which was altered in the experiments in a controllable way) together with an external magnetic field will determine the charge state and emission intensity of the QDs.
Asunto(s)
Arsenicales/química , Cristalización/métodos , Indio/química , Mediciones Luminiscentes/métodos , Modelos Químicos , Nanoestructuras/química , Nanotecnología/métodos , Puntos Cuánticos , Simulación por Computador , Magnetismo , Nanoestructuras/ultraestructura , Tamaño de la PartículaRESUMEN
InAs/GaAs quantum dots have been subjected to a lateral external electric field in low-temperature microphotoluminescence measurements. It is demonstrated that the dot PL signal could be increased several times depending on the magnitude of the external field and the strength of the internal (built-in) electric field, which could be altered by an additional infrared illumination of the sample. The observed effects are explained by a model that accounts for the essentially faster lateral transport of the photoexcited carriers achieved in an electric field.
Asunto(s)
Arsenicales/química , Campos Electromagnéticos , Galio/química , Indio/química , Teoría Cuántica , LuminiscenciaRESUMEN
Individual quantum dots have been studied by means of microphotoluminescence with dual-laser excitation. The additional infrared laser influences the dot charge configuration and increases the dot luminescence intensity. This is explained in terms of separate generation of excess electrons and holes into the dot from the two lasers. With increasing dot density and/or sample temperature, the increase of the luminescence intensity vanishes progressively, while the possibility to control the dot charge remains.